Kenmore Refrigerator 106.53252202 (10653252202, 106 53252202) Parts

Ice crusher not working or producing inconsistent crushed ice? This rotating crusher blade restores proper ice crushing when worn, bent, or cracked.

This is a trim rail or retaining bar that attaches to the inside of a refrigerator or freezer door to hold a shelf bin in place. It clips onto the door liner and supports the shelf so items stay organized and secure. Replace this rail if it is cracked, broken, or no longer holds the door shelf securely, causing items to fall.

This thermostat retainer clip secures the defrost thermostat to the evaporator tubing in your refrigerator or freezer, maintaining firm contact for accurate temperature sensing and dependable defrost operation.

• Holds the thermostat firmly against the evaporator line for proper temperature feedback
• Helps prevent a loose or dangling thermostat that contribute to frost buildup and poor defrost performance
• Restores correct mounting when the original clip is cracked, bent, or missing
• Common signs include a broken clip or a thermostat not attached to the coil

• Disconnect power to the appliance before servicing; wear cut-resistant gloves
• Access the evaporator compartment; remove accumulated frost/ice as needed without prying on coil fins
• Position the thermostat body flat against the tubing and snap the retainer over it, avoiding pinched wires or damaged fins
• Confirm a secure fit and proper wire routing before reassembling and restoring power

Fix ice not dispensing properly with this ice crusher blade. Replaces free-wheeling or worn blades on the auger assembly. DIY-friendly repair.

White plastic hinge cover for refrigerator doors. Replaces cracked, broken, or missing hinge covers. Installs over door hinge mechanism for clean look.

Rubber grommet kit that mounts and cushions the compressor. Replace worn, cracked, or damaged grommets to restore proper support and isolation.

Fix ice that won't crush or dispense with this refrigerator crusher blade. Solves bent or damaged blades preventing ice from dispensing. Easy DIY repair.

Ice maker not dispensing cubes properly? This stripper arm guides ice through the maker. Common fix when tabs break. Takes about 15 minutes to install.

Replacement mounting screw for refrigerators. Secures panels, trim pieces, and small assemblies. Needed when original screw is missing or damaged.

White plastic hinge cover for refrigerator doors. Replaces cracked, broken, or missing hinge covers that expose door hardware. Snaps into place.

Black plastic hinge cover cap for side-by-side refrigerators. Replaces cracked, broken, or missing hinge covers that expose internal hardware.

This is a replacement 1/4-20 threaded screw used to secure appliance components and panels. It restores proper fastening where a matching screw is missing, loose, or stripped and helps stop rattling or misalignment. What it does:

• Secures panels, brackets, and assemblies to maintain proper alignment and reduce vibration
• Replaces missing or damaged fasteners that cause loose or rattling parts
• Works wherever a 1/4-20 threaded screw is specified by the manufacturer
• Simple mechanical fastener—no electrical or calibration changes required

• Disconnect power to the appliance before servicing to avoid injury
• Use the matching driver and thread engagement; do not overtighten to prevent stripping
• Verify screw length and head type match the original before installing
• If threads are damaged, repair or replace the mating component rather than forcing the screw

Directs chilled air through the fresh-food compartment to maintain even cooling. Replace if cracked, broken, or missing to restore proper airflow.

This small metal mounting clip secures the thermal fuse in place to maintain proper thermal contact and stable wiring. It helps keep the fuse positioned so the appliance can monitor temperature reliably and operate safely. What it does:

• Secures the thermal fuse to the appliance housing or duct to prevent movement
• Keeps the fuse in correct contact with temperature-sensing surfaces
• Helps prevent intermittent heating or thermal-sensor misreads caused by a loose fuse
• Useful when replacing a damaged or missing fuse retainer during fuse service

• One thermal fuse mounting clip

• Disconnect power to the appliance before servicing to avoid shock or injury
• Remove access panels per your model's service instructions to reach the fuse location
• Install clip in the same orientation as the original; use pliers if needed to seat it firmly
• Inspect the thermal fuse and wiring while installing; replace any damaged components per OEM guidance

This is an escutcheon assembly that mounts on the deli or meat pan drawer and houses the humidity or temperature control slide. It provides the frame and mechanism that lets you adjust airflow to keep deli meats and cheeses at the proper temperature. Replace this part if the slide is broken, the escutcheon is cracked, or you can no longer adjust the drawer's temperature setting.

Replace your refrigerator's damaged or frayed wire harness. Essential wiring component that connects electrical systems. Order now if yours is broken or worn.