Kenmore Refrigerator 106.54789801 (10654789801, 106 54789801) Parts

Put the new hinges on the doors fyi you need to tell what size the screws are for the hinge kits would help a lot Read more

Easy to remove the metal parts from the old bin. The only problem was that the screw that holds the adapter has red thread locker and screwdriver rounded off the head of the screw. Drilled the screw and heated the screw to loosen the thread locker and used an ease out to remove the screw. Read more

Removed the handle with two screws on the inside front and pulled out the custom wood panel. Pulled the compactor out from under cabinet. Tipped it over on back of unit, supporting it with a little foot stool. Unscrewed two lower screws at bottom of unit holding black trim panel (that held wood panel in place) and lower black rubber flap. Removed two screws on lower outside side of unit that held the foot pedal. Slid off black U shaped metal frame from top of compactor towards bottom. Slid on... Read more

I decided if one needed replacing I might as well both two--made sense to me. None were available locally so I ordered them on-line. Surprisingly they came sooner than I expected. I also found a video on the internet that clearly showed the procedure. The actual repairs took 15 minutes or less. One good suggestion from the video was to run the screw in and out of the wheel bracket before final mounting. The video also suggested putting something under the corner to eliminate tipping. The... Read more

Replaced tired motor and chute door seal plate... Through outside of unit door - I have worked in the appliance repair field for years Read more

Rather than fighting the set screw, I ordered a new handle and extra parts to fix it. My father taught me to use anti seize which I used on all the threaded materials. Appliance parts and all the parts listed easy to see and Order Read more

Myself Read more

Replaced both sets of door cams on my Kenmore Elite Refrigerator. The most important thing to know is that you DO NOT have to remove the doors from the refrigerator to replace BOTH sets of cams. You just have to remove the lower grill which is a snap fit (I also turned off the water and unplugged the unit). My fridge has an ice and water dispenser where the water and electrical lines go through the cams on the left side. Be sure to order the correct parts as the cam holes on the freezer side... Read more

Removed broken crisper drawer , had to remove a sliding humidity control slider that was snapped in, and another slide attatched to handle of drawer , my grandon did both for me and the new crisper pan was put in place Delivery was 3 days , could of been quicker if I choose but it was not an emergency repair . It was package well also and best part the price was 25% lower than Sears ! Read more

I watched the helpful viedo and the job was easy. Read more

So easy to replace the Diffuser, in less than 5 minutes. Read more

• Light not working

We actually were able to determine that one of the freezer switches was bad and taped it down for about 3 days. The beeping stopped. Our fridge has two freezer switches and one fridge side switch. I ordered all three from these guys. They were cheaper than Whirlpool by about $20 for parts and about $15 for shipping. The part numbers had superseded too many times to count, usually that doesn't matter but in this case it did. The new parts were just slightly bigger than the old parts AND... Read more

Replaced bad condenser motor Read more

Replaced It With New One Read more

The video was great - followed the instructions - replaced the parts - icemaker is working like new now. Read more

Replaced the 2 parts that had broken (due to the wrong plastic selection by Kenmore IMO. The motor needed to be re-clocked but this video https://youtu.be/QK8C8rxbkhc gave the information needed. Between AppliancePartsPros.com and youtube I have rebuilt this fridge (water valve, Ice maker, Auger gearbox and ice shute door) Probably could do the job in about 30 minutes now that I know how and exactly what needs to be done. Only needed the pliers to turn the motor shaft Read more