Kenmore Refrigerator 106.55122700 (10655122700, 106 55122700) Parts
Genuine Whirlpool part
By: Whirlpool
Part Number: WPW10224328
For the complete ice door kit order W10823377.
Do-It-Yourself Stories from Customers like You
Ice dispenser chute door was not closing or sealing Robert H. • West Palm Bch , FL • July 23, 2025
The ice dispenser chute door had not been sealing for years. The ice cubes on the lower portion of the ice bin would melt enough eventually to then freeze up into a big, amalgamated blob of ice due to ambient air coming up the chute. This melt-then-freeze would happen, to the extent the chute froze to its own closure. Despite service technician visits over a period of six years nothing they did resolved the issue. I opened the freezer door to reach into the bin from the top to extract usable...
Read more
More
$48.95
- Compare At:
-
$57.76
- You Save:
-
$8.81
Genuine Whirlpool part
By: Whirlpool
Part Number: WP2203771
The Top Hinge is an OEM part for Whirlpool refrigerators. This hinge ensures the proper alignment and smooth operation of the refrigerator door, allowing it to open and close securely. It supports the weight of the door and helps maintain an airtight seal.
Causes of a bad top hinge can include general wear and tear, heavy use, or accidental damage.
Symptoms of a bad top hinge include:
- Refrigerator door sagging or misaligned
- Difficulty in opening or closing the door
- Door not sealing properly, leading to temperature fluctuations
- Unusual noises when the door is operated
This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.
Do-It-Yourself Stories from Customers like You
Needed hinges for doors William H. • Niles , MI • September 22, 2015
Put the new hinges on the doors fyi you need to tell what size the screws are for the hinge kits would help a lot
Read more
More
$51.26
- Compare At:
-
$61.00
- You Save:
-
$9.74
Genuine Whirlpool part
By: Whirlpool
Part Number: W10852691
This baffle sits in the ice bin and supports the auger so ice feeds smoothly to the dispenser. Replace a cracked or worn baffle to restore reliable dispensing and reduce jams or grinding from the ice bucket.
- Supports and aligns the ice auger inside the bin
- Guides cubes/crushed ice toward the crusher/dispenser
- Helps prevent auger wobble, binding, or excessive noise
- Failure can show as weak/no ice dispensing or intermittent jams
What's included: 1 baffle Install notes:
- Disconnect power; remove the ice bin from the freezer/door
- Empty the bin and remove any screws/clips securing the baffle
- Transfer any reusable hardware; orient the baffle correctly around the auger
- Tighten fasteners without overtightening; reinstall bin and test dispense
Do-It-Yourself Stories from Customers like You
The ice crusher mechanism on my ice maker wasn't working properly i was getting bits of white plastic in my ice so obviously something was broken in there Tawna M. • Orem , UT • July 27, 2015
I found a video/tutorial on how to take it apart to see what was pieces were broken, then ordered the replacement parts and watched the video to put it back together again.
Read more
More
$25.95
- Compare At:
-
$30.62
- You Save:
-
$4.67
Genuine Whirlpool part
By: Whirlpool
Part Number: WP2206671B
Color: black. Measures about 9 inches wide by 2-1/2 inches deep.
Do-It-Yourself Stories from Customers like You
Stopped dispensing water Cristopher C. • Santa Rosa , CA • July 15, 2016
Ordered the parts. Watched a great video on this web site. Installed. Fixed. Easy peesey.
Read more
More
$55.38
- Compare At:
-
$65.35
- You Save:
-
$9.97
Genuine Whirlpool part
By: Whirlpool
Part Number: WP489478
Size: 8 x 1/2 ab.
Do-It-Yourself Stories from Customers like You
Wanted to update wood paneled compactor Julie S. • San Antonio , TX • December 09, 2014
Removed the handle with two screws on the inside front and pulled out the custom wood panel. Pulled the compactor out from under cabinet. Tipped it over on back of unit, supporting it with a little foot stool. Unscrewed two lower screws at bottom of unit holding black trim panel (that held wood panel in place) and lower black rubber flap. Removed two screws on lower outside side of unit that held the foot pedal. Slid off black U shaped metal frame from top of compactor towards bottom. Slid on...
Read more
More
$5.95
- Compare At:
-
$7.02
- You Save:
-
$1.07
Genuine Whirlpool part
By: Whirlpool
Part Number: W11233072
This factory screw secures appliance components to their mounting points. Replace missing, worn, or stripped hardware to restore a tight fit, proper alignment, and quieter operation across the affected assembly.
- Fastens panels, brackets, covers, or internal parts to the chassis or frame
- Helps maintain alignment and support, reducing rattle, vibration, or looseness
- Replaces missing or damaged screws that have backed out, broken, or stripped
- Restores secure mounting after service when original hardware is lost
What's included: 1 screw Install notes:
- Disconnect power; shut off water or gas supplies before servicing
- Use the correct driver; start threads by hand to avoid cross-threading
- Match length and thread to the original location; do not substitute with longer hardware
- Tighten snugly; do not overtighten into plastic or thin metal
Do-It-Yourself Stories from Customers like You
Bake element broken on jenn air model s125 downdraft slide in range Patricia D. • Raleigh , NC • May 02, 2015
Ordered Bake Element, Y04100019 (Whirlpool AP4283614) to replace a broken bake element on my 30-year old Jenn-Air Model S125 Downdraft Slide-in electric range. Received the element very quickly but it had been damaged in shipping. Called AppliancePartsPros to report this and they quickly shipped another element - very easy process.
To install the element, I turned off the power to the range, put on rubber gloves (just in case) and removed the two sheet metal crews at the rear of the oven -...
Read more
More
$20.95
- Compare At:
-
$24.93
- You Save:
-
$3.98
Genuine Whirlpool part
By: Whirlpool
Part Number: WPW10250570
This cabinet roller assembly supports the refrigerator at the base and lets you roll the unit forward for cleaning or service. Replace a cracked or seized roller to restore smooth movement and a stable, level stance. What it does:
- Supports the refrigerator cabinet and helps maintain proper leveling
- Allows the unit to roll for easier cleaning and servicing
- Replaces worn, cracked, or seized rollers and damaged brackets
- Helps resolve wobbling, uneven stance, scraping noises, or difficulty moving the fridge
What's included:
- One complete cabinet roller assembly
Install notes:
- Disconnect power and turn off the water supply before servicing
- Protect flooring and use a second person or an appliance dolly to safely tilt or move the unit
- Remove mounting fasteners, swap the assembly in the original position, and reuse hardware if applicable
- After installation, level the refrigerator and verify doors close and seal properly
Do-It-Yourself Stories from Customers like You
The plastic left rear wheel was coming apart and needed replacing Gary H. • San Antonio , TX • June 11, 2016
I decided if one needed replacing I might as well both two--made sense to me. None were available locally so I ordered them on-line. Surprisingly they came sooner than I expected. I also found a video on the internet that clearly showed the procedure. The actual repairs took 15 minutes or less. One good suggestion from the video was to run the screw in and out of the wheel bracket before final mounting. The video also suggested putting something under the corner to eliminate tipping. The...
Read more
More
$27.95
- Compare At:
-
$33.26
- You Save:
-
$5.31
Genuine Whirlpool part
By: Whirlpool
Part Number: WP2323197
This defrost heater warms the evaporator during automatic defrost to melt built-up frost so air can move freely and temperatures stay consistent. Replace a failed heater to restore normal cooling and end recurring frost on the freezer panel.
- Melts ice from the evaporator coil during the defrost cycle
- Prevents frost buildup that restricts airflow and causes warm spots
- Helps maintain stable refrigerator and freezer temperatures
- Typical failure signs: heavy frost on the back wall, reduced cooling, fan noise from ice contact, frequent manual defrosting
Includes: 1 defrost heater
- Disconnect power before servicing; wear cut-resistant gloves
- Access through the freezer compartment; remove shelves/ice bin and rear panel to reach the evaporator
- Match wire connections and route leads exactly as original; keep wiring clear of the fan and sharp edges
- After reassembly, restore power and monitor a defrost cycle; if frost quickly returns, also evaluate the defrost thermostat and control
Do-It-Yourself Stories from Customers like You
Coil freezing and icing up Bob J. • Mchenry , IL • April 30, 2016
I replaced the defrost control and heater just to be sure. I usedmthe helpful video and though it took me 2 hours i gotmit done and saved hundreds
Read more
More
$61.75
- Compare At:
-
$74.10
- You Save:
-
$12.35
Genuine Whirlpool part
By: Whirlpool
Part Number: WPW10152859
Color: Black
Do-It-Yourself Stories from Customers like You
Refrigerator water dispenser stopped working Carlos R. • Houston , TX • September 19, 2014
The water dispenser stopped working on my Sears Kenmore (Whirlpool) side-by-side refrigerator and after much research on the web I purchased the parts that commonly failed for this condition. I should have first taken the dispenser assembly apart but I didn't--it looked a little too intimidating to do twice. As it turns out, what actually broke was the plastic assembly that holds the water actuator switch in place so the dispenser lever could not strike it. I was able to secure it in place...
Read more
More
$51.28
- Compare At:
-
$61.02
- You Save:
-
$9.74
Genuine Whirlpool part
By: Whirlpool
Part Number: WP2196483
The Shelf Stud is an OEM part for Whirlpool refrigerators. It serves as a support peg that holds the refrigerator shelves in place, ensuring they remain stable and properly positioned.
Causes of a bad shelf stud can include wear and tear from regular use, accidental impact that causes the stud to break, or repeated removal and reinstallation of shelves leading to loosening or damage.
Symptoms of a bad shelf stud include:
- Shelves not staying securely in place
- Shelves tilting or collapsing
- Visible cracks or damage to the stud
- Difficulty in inserting or removing shelves
This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.
This is a rear stud with a screw. For the front stud with screw use part number W11223328. For studs with no screw use kit part number 4388538.
Do-It-Yourself Stories from Customers like You
Broken shelf and drawer. Regina M. • Yardley , PA • November 10, 2017
Myself
Read more
More
$10.95
- Compare At:
-
$13.03
- You Save:
-
$2.08
Genuine Whirlpool part
By: Whirlpool
Part Number: WP2155013
Clip for bottom grill. If your original clip is riveted, order screw WP489478.
Do-It-Yourself Stories from Customers like You
Leaking refrigerator no ice or water from dispensers Thomas H. • Arlington , VA • October 09, 2016
I had to remove a metal panel at the bottom back of the freezer as well as a couple of shelf slides in order to get at a drain pan in the back. It was frozen solid, so I stabbed at it with an ice pick until I broke through, followed up by poking a coat hanger in the drain hole to clear as much as I could, then poured a little boiling water over it to follow up. After screwing it all back together, the ice maker surprisingly was working again in less than 20 minutes. I also replaced a broken...
Read more
More
$5.95
- Compare At:
-
$7.08
- You Save:
-
$1.13
Genuine Whirlpool part
By: Whirlpool
Part Number: WP2206629B
Color: Black
Do-It-Yourself Stories from Customers like You
Broken can Rayniero S. • Rockledge , FL • July 10, 2016
Ordered the parts, took door off the refrigerator. Removed all parts and replace with new parts. Took me about 15 minutes to complete.
Read more
More
$26.95
- Compare At:
-
$32.34
- You Save:
-
$5.39
Genuine Whirlpool part
By: Whirlpool
Part Number: WP2206671W
Color: white. Measures about 9 inches wide by 2-1/2 inches deep.
Do-It-Yourself Stories from Customers like You
No filtered water Donald H. • Elk River , MN • July 19, 2015
Gas insurance won't fix dispensing mechanism. Went to Youtube and watched video. Googled appliance parts, you looked reputable and took paypal. Ordered parts, repair took about 10 minutes. Thank you
Read more
More
$51.27
- Compare At:
-
$61.52
- You Save:
-
$10.25
Genuine Whirlpool part
By: Whirlpool
Part Number: WP2309758
This freezer bin replaces a cracked or missing bin to restore organized storage in your freezer. It mounts on existing tabs or rails to keep frozen items secure and easy to access.
- Provides storage and organization within the freezer compartment
- Replaces a broken, warped, or missing bin
- Helps prevent items from tipping or falling when the door opens
- Restores proper fit so the bin stays seated on its mounts
What's included: One freezer bin. Install notes:
- Power isn't required for this replacement; open the freezer and remove items from the affected area
- Lift the old bin straight up and out from the tabs/rails
- Align the new bin with the mounting points and slide or press down until fully seated
- Do not force into place; distribute weight evenly and avoid overloading
Do-It-Yourself Stories from Customers like You
Bin freezer broken Arthur H. • Miami , FL • May 16, 2016
I found the correct part and oredered. It was really great to receive that by next day in and I installed it.
I would recommend and use myself ApplianceParts Pro any time.
Arthur Hem
Read more
More
$73.95
- Compare At:
-
$88.00
- You Save:
-
$14.05
Genuine Whirlpool part
By: Whirlpool
Part Number: WPW10143759
Do-It-Yourself Stories from Customers like You
Failed to cool due to hole/s in evaporator leaking freon Gerald L. • Myrtle Beach , SC • August 17, 2017
Ordered new Evaporator part and Drier from Appliance Pros. The part arrived earlier than expected and was properly packaged. I had both parts installed by a professional as they required a level of expertise above my capabilities. Works perfectly.
Read more
More
$28.23
- Compare At:
-
$33.59
- You Save:
-
$5.36
Genuine Whirlpool part
By: Whirlpool
Part Number: WP3196557
This replacement screw secures appliance panels and components so they stay tight and aligned during use. Replacing a missing or damaged screw restores a solid fit and helps eliminate rattles, loose trim, or shifting parts.
- Fastens brackets, panels, trim, or components to the appliance chassis
- Helps correct loose or missing hardware after vibration or service
- Replaces stripped, rusted, or broken screws
- Can reduce rattling noises or misaligned parts caused by missing fasteners
What's included: One screw Install notes:
- Disconnect power; for gas appliances, also shut off the gas supply
- Support the part being fastened; start threads by hand to avoid cross-threading
- Use the correct driver size; tighten snugly without overtightening
- Replace hardware with the exact part number to ensure proper fit
Do-It-Yourself Stories from Customers like You
Water dispenser was no longer working Kelly W. • Houston , TX • January 24, 2017
After being told by a service repairman that it would cost me close to $200 to repair, I resolved to just not use the dispenser. After about a year, I had decided that I wanted to repair it and would look at the options myself. At the least, I could figure out which parts were needed to repair it and have them on hand for a service guy if I determined I could not do the job myself. The more I studied it, the more I felt confident that I could do it, and sure enough, when the part arrived - a...
Read more
More
$5.95
- Compare At:
-
$7.08
- You Save:
-
$1.13