Kenmore Refrigerator 106.57786701 (10657786701, 106 57786701) Parts
Genuine Whirlpool part
By: Whirlpool
Part Number: W11512417
The Refrigerator Drain Connector is an OEM part for Whirlpool refrigerators. It is responsible for directing water and condensation from the evaporator fan coil and defrost into the drain pan.
Causes of a bad drain connector can include cracks, breaks or deformations caused by repeated thermal cycling or impact damage. Mineral or lime buildup inside the connector over many years can also restrict water flow.
Symptoms of a bad drain connector include:
- Water or condensation leaks around the connector area
- Puddles or watermarks on the floor behind the fridge
- Slow drainage of water from the evaporator fan coil
- Mold or mildew growth near the connector or drain area
This replacement part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.
Do-It-Yourself Stories from Customers like You
The problem was ice buildup on the floor of the freezer William B. • Pahoa , HI • January 15, 2016
A YouTube video: https://www.youtube.com/watch?v=jIdtNdDXFDk , by a professional appliance repair company described replacement of the freezer drain pipe with Kenmore's (by Whirlpool) revised drain pipe. Ice buildup inside the freezer was caused by warm air beneath the freezer contacting cold air from inside the freezer the resulting condensation freezing and blocking the drain, causing the ice buildup inside. The revised drain tube functions as a p-trap to prevent cold/warm air interaction....
Read more
More
$25.95
- Compare At:
-
$31.14
- You Save:
-
$5.19
Genuine Whirlpool part
By: Whirlpool
Part Number: WP2203771
The Top Hinge is an OEM part for Whirlpool refrigerators. This hinge ensures the proper alignment and smooth operation of the refrigerator door, allowing it to open and close securely. It supports the weight of the door and helps maintain an airtight seal.
Causes of a bad top hinge can include general wear and tear, heavy use, or accidental damage.
Symptoms of a bad top hinge include:
- Refrigerator door sagging or misaligned
- Difficulty in opening or closing the door
- Door not sealing properly, leading to temperature fluctuations
- Unusual noises when the door is operated
This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.
Do-It-Yourself Stories from Customers like You
Needed hinges for doors William H. • Niles , MI • September 22, 2015
Put the new hinges on the doors fyi you need to tell what size the screws are for the hinge kits would help a lot
Read more
More
$51.26
- Compare At:
-
$61.00
- You Save:
-
$9.74
Genuine Whirlpool part
By: Whirlpool
Part Number: WP2198608
The Whirlpool latch spring is an OEM replacement part responsible for securing the ice container or bin in place on a refrigerator. Its main function is to provide tension and support to the ice container latch, allowing it to engage and disengage properly. When the ice container is inserted into the refrigerator's ice compartment, the latch spring ensures that it securely locks in place, preventing accidental spillage of ice.
Causes of a bad latch spring can include metal fatigue from repeated use, rust or corrosion from exposure to moisture, or physical damage from accidental impacts.
Symptoms of a bad latch spring include:
- The ice container not staying in place and sliding out of position
- Difficulty in properly attaching or detaching the ice container from the refrigerator
- The ice container feeling loose or wobbly when inside the ice compartment
- The ice container not aligning correctly with the ice dispenser or auger
This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.
Do-It-Yourself Stories from Customers like You
Lower ice bin broken Dennis B. • Wichita Falls , TX • March 30, 2020
Easy to remove the metal parts from the old bin. The only problem was that the screw that holds the adapter has red thread locker and screwdriver rounded off the head of the screw. Drilled the screw and heated the screw to loosen the thread locker and used an ease out to remove the screw.
Read more
More
$5.95
- Compare At:
-
$7.14
- You Save:
-
$1.19
Genuine Whirlpool part
By: Whirlpool
Part Number: WP489478
Size: 8 x 1/2 ab.
Do-It-Yourself Stories from Customers like You
Wanted to update wood paneled compactor Julie S. • San Antonio , TX • December 09, 2014
Removed the handle with two screws on the inside front and pulled out the custom wood panel. Pulled the compactor out from under cabinet. Tipped it over on back of unit, supporting it with a little foot stool. Unscrewed two lower screws at bottom of unit holding black trim panel (that held wood panel in place) and lower black rubber flap. Removed two screws on lower outside side of unit that held the foot pedal. Slid off black U shaped metal frame from top of compactor towards bottom. Slid on...
Read more
More
$5.95
- Compare At:
-
$7.02
- You Save:
-
$1.07
Genuine Whirlpool part
By: Whirlpool
Part Number: WP2305258
The Door Chute is an OEM part for Whirlpool refrigerators. This part directs ice from the ice maker into the ice bucket or dispenser chute. The door chute ensures a smooth and controlled flow of ice, preventing spills and maintaining the efficiency of the ice dispensing system.
Common issues include cracks, warping, or blockages that can obstruct the flow of ice and affect the dispenser's performance.
Symptoms of a bad door chute include:
- Ice not dispensing properly
- Ice jamming or clogging in the chute
- Leaks or drips around the ice dispenser area
- The door chute not sealing correctly
This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.
Do-It-Yourself Stories from Customers like You
Ice maker door wouldn’t open Mickey W. • Ponca City , OK • April 20, 2020
Talked to a service rep. and he helped me diagnose what was needed.
Read more
More
$15.47
- Compare At:
-
$18.41
- You Save:
-
$2.94
Genuine Whirlpool part
By: Whirlpool
Part Number: WP2196483
The Shelf Stud is an OEM part for Whirlpool refrigerators. It serves as a support peg that holds the refrigerator shelves in place, ensuring they remain stable and properly positioned.
Causes of a bad shelf stud can include wear and tear from regular use, accidental impact that causes the stud to break, or repeated removal and reinstallation of shelves leading to loosening or damage.
Symptoms of a bad shelf stud include:
- Shelves not staying securely in place
- Shelves tilting or collapsing
- Visible cracks or damage to the stud
- Difficulty in inserting or removing shelves
This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.
This is a rear stud with a screw. For the front stud with screw use part number W11223328. For studs with no screw use kit part number 4388538.
Do-It-Yourself Stories from Customers like You
Broken shelf and drawer. Regina M. • Yardley , PA • November 10, 2017
Myself
Read more
More
$10.95
- Compare At:
-
$13.03
- You Save:
-
$2.08
Genuine Whirlpool part
By: Whirlpool
Part Number: W11778262
This cam-door is the small pivoting cam that helps a washer/dryer or laundry door latch and swing smoothly. Replacing a worn or broken cam restores proper door movement and helps the door close and seal reliably. What it does:
- Acts as the pivot/latch cam that guides the appliance door during opening and closing.
- Helps the door engage the latch and maintain correct alignment.
- Commonly used to stop a door from hanging, binding, or failing to stay closed.
- Can reduce door noise or catching caused by a damaged cam.
What's included: Includes: One cam-door. Install notes:
- Disconnect power (unplug or switch off breaker) before starting any repair.
- Support the door or cabinet panel during removal to prevent dropping or damage.
- Remove the door or access panel and replace the cam using basic hand tools; keep track of fasteners.
- After reassembly, check door operation and latch engagement before returning the appliance to service.
Do-It-Yourself Stories from Customers like You
Door clicking, door not closing easily Mike K. • Broadview Heights , OH • January 27, 2020
Replaced both sets of door cams on my Kenmore Elite Refrigerator. The most important thing to know is that you DO NOT have to remove the doors from the refrigerator to replace BOTH sets of cams. You just have to remove the lower grill which is a snap fit (I also turned off the water and unplugged the unit). My fridge has an ice and water dispenser where the water and electrical lines go through the cams on the left side. Be sure to order the correct parts as the cam holes on the freezer side...
Read more
More
$6.89
- Compare At:
-
$7.50
- You Save:
-
$0.61
Genuine Whirlpool part
By: Whirlpool
Part Number: WP2155013
Clip for bottom grill. If your original clip is riveted, order screw WP489478.
Do-It-Yourself Stories from Customers like You
Leaking refrigerator no ice or water from dispensers Thomas H. • Arlington , VA • October 09, 2016
I had to remove a metal panel at the bottom back of the freezer as well as a couple of shelf slides in order to get at a drain pan in the back. It was frozen solid, so I stabbed at it with an ice pick until I broke through, followed up by poking a coat hanger in the drain hole to clear as much as I could, then poured a little boiling water over it to follow up. After screwing it all back together, the ice maker surprisingly was working again in less than 20 minutes. I also replaced a broken...
Read more
More
$5.95
- Compare At:
-
$7.08
- You Save:
-
$1.13
Genuine Whirlpool part
By: Whirlpool
Part Number: WP4387911
This push-button door switch senses when your refrigerator door opens and closes to control the interior light. Replace a worn or stuck switch to restore reliable lighting and proper on/off operation when the door moves. What it does:
- Turns the interior light on when the door opens and off when it closes
- Common fix for a light that won't turn on with the door open
- Resolves lights that stay on continuously with the door closed
- Addresses intermittent lighting from a sticking or damaged plunger
What's included:
Install notes:
- Disconnect power to the refrigerator before servicing
- Carefully pry the old switch from the liner; protect the surface to avoid damage
- Transfer wires to the new switch one at a time to maintain correct connections
- Press the new switch fully into place and restore power to test operation
Do-It-Yourself Stories from Customers like You
A failed freezer door switch was causing the fridge to display that the door was open when it was not this caused it to beep at random Kara H. • Charleston , SC • March 08, 2016
We actually were able to determine that one of the freezer switches was bad and taped it down for about 3 days. The beeping stopped. Our fridge has two freezer switches and one fridge side switch. I ordered all three from these guys. They were cheaper than Whirlpool by about $20 for parts and about $15 for shipping. The part numbers had superseded too many times to count, usually that doesn't matter but in this case it did. The new parts were just slightly bigger than the old parts AND...
Read more
More
$26.95
- Compare At:
-
$32.07
- You Save:
-
$5.12
Genuine Whirlpool part
By: Whirlpool
Part Number: WP2223752
Mounts on the bottom of the freezer door.
Do-It-Yourself Stories from Customers like You
Door clicking, door not closing easily Mike K. • Broadview Heights , OH • January 27, 2020
Replaced both sets of door cams on my Kenmore Elite Refrigerator. The most important thing to know is that you DO NOT have to remove the doors from the refrigerator to replace BOTH sets of cams. You just have to remove the lower grill which is a snap fit (I also turned off the water and unplugged the unit). My fridge has an ice and water dispenser where the water and electrical lines go through the cams on the left side. Be sure to order the correct parts as the cam holes on the freezer side...
Read more
More
$14.95
- Compare At:
-
$17.79
- You Save:
-
$2.84
Genuine Whirlpool part
By: Whirlpool
Part Number: 4210463RW
This flexible, narrow brush reaches under and behind the cabinet to sweep dust and lint from condenser coils and vents. Cleaning built-up debris helps restore airflow and support proper cooling performance.
- Sweeps dust, lint, and pet hair from condenser coils and ventilation areas
- Flexible reach helps access coils beneath or behind the appliance
- Aids proper heat dissipation by clearing airflow paths
- Helpful when coils are visibly dirty, cooling seems weak, or the unit runs longer than usual
What's included: 1 condenser coil cleaning brush
- Unplug or disconnect power before cleaning
- Remove the toe grille or rear access panel if needed to access coils
- Brush gently along the coil fins; avoid bending fins or damaging tubing
- Vacuum or wipe up loosened debris before replacing any panels and restoring power
Do-It-Yourself Stories from Customers like You
Failed condenser motor John F. • New Palestine , IN • February 29, 2016
Replaced bad condenser motor
Read more
More
$28.25
- Compare At:
-
$33.62
- You Save:
-
$5.37
Genuine Whirlpool part
By: Whirlpool
Part Number: WPW10311033
Color: Black
Do-It-Yourself Stories from Customers like You
Grill was mussing Jane R. • Ridgeland , MS • July 09, 2017
I was able to pop the new grill into place.
Read more
More
$90.95
- Compare At:
-
$108.23
- You Save:
-
$17.28
Genuine Whirlpool part
By: Whirlpool
Part Number: 72032
Bottle with brush. Color: Black. Size: 0.6 fl.oz.
Do-It-Yourself Stories from Customers like You
Leaking diaphragm Herbert S. • Monroe Township , NJ • January 03, 2015
Replaced It With New One
Read more
More
$17.76
- Compare At:
-
$21.13
- You Save:
-
$3.37
Genuine Whirlpool part
By: Whirlpool
Part Number: WP2318736
This large refrigerator door shelf retainer bar secures items on the door shelf, keeping jars and bottles from sliding out during everyday use. Replace a broken or missing bar to restore safe, reliable door storage.
- Holds contents on the refrigerator door shelf; stabilizes items when the door opens or closes
- Replace when the bar is cracked, warped, or missing
- Common symptoms: items fall from the door shelf, bar won't stay attached, loose fit
- For the refrigerator compartment door in the large position
What's included: One large refrigerator door shelf retainer bar Installation notes:
- Remove items from the affected shelf; allow cold plastic to warm to room temperature before handling
- Release the old bar from the endcaps or slots and inspect mounting points for damage
- Align and snap the new bar fully into both ends; verify a secure fit before reloading
- No power is typically required; wear gloves and avoid excessive force to prevent cracking
Do-It-Yourself Stories from Customers like You
Bottom door shelf needed to be replaced Robert R. • Crandall , TX • May 21, 2021
Ordered new part and installed it myself.
Read more
More
$53.95
- Compare At:
-
$55.48
- You Save:
-
$1.53
Genuine Whirlpool part
By: Whirlpool
Part Number: WP2305204
This part is the dispenser ice door support. It mounts and aligns the ice chute flapper (ice door) in the freezer door so it pivots and seals correctly, helping reduce warm air leaks, frost, and ice clumping. What it does:
- Provides the pivot/mount for the dispenser ice chute door (flapper)
- Keeps the ice chute door aligned to help maintain a proper seal
- Wear or broken tabs may cause the flapper to stick open/closed
- May lead to frost in the chute, condensation, air leaks, or clumping ice
What's included:
Install notes:
- Unplug the refrigerator and remove the ice bin before servicing
- Remove dispenser trim/control to access the chute assembly
- Note spring and flapper orientation; transfer the door, seal, spring, and any hardware to the new support
- Verify smooth flapper movement and full seal before reassembly and restoring power
Do-It-Yourself Stories from Customers like You
Replaced 2 broken parts saved fridge. Roger M. • Ravenna , OH • June 17, 2023
Replaced the 2 parts that had broken (due to the wrong plastic selection by Kenmore IMO.
The motor needed to be re-clocked but this video https://youtu.be/QK8C8rxbkhc gave the information needed.
Between AppliancePartsPros.com and youtube I have rebuilt this fridge (water valve, Ice maker, Auger gearbox and ice shute door)
Probably could do the job in about 30 minutes now that I know how and exactly what needs to be done. Only needed the pliers to turn the motor shaft
Read more
More
$43.95
- Compare At:
-
$51.86
- You Save:
-
$7.91
Genuine Whirlpool part
By: Whirlpool
Part Number: WPW10143759
Do-It-Yourself Stories from Customers like You
Failed to cool due to hole/s in evaporator leaking freon Gerald L. • Myrtle Beach , SC • August 17, 2017
Ordered new Evaporator part and Drier from Appliance Pros. The part arrived earlier than expected and was properly packaged. I had both parts installed by a professional as they required a level of expertise above my capabilities. Works perfectly.
Read more
More
$28.23
- Compare At:
-
$33.59
- You Save:
-
$5.36