Kenmore Refrigerator 106.58943803 (10658943803, 106 58943803) Parts

It was not looking good. I could not order the part I needed as it was part of the door - eve though it had screws att Hong it to the freezer door. At one web site it was a replacement of the whole freezer door!/? Luckily I ventured further and found this repair kit and video instructions. My order arrived in 3 days, and the install (thanks to the video) was easy. A whole lot better than buying a new freezer door - not! BTW - Whitlpool should not have made the tabs out of plastic, the metal... Read more

Undid a handful of screws, put the new panel in place and screwed them back in. Read more

Was stuck finding the correct parts, as the numbers on the Whirlpool website did not match exactly. But your rep was very patient and helpful with measurements and descriptions to help me find the exact parts I needed. Everything was perfect! Thanks ever so much. Read more

I found a video/tutorial on how to take it apart to see what was pieces were broken, then ordered the replacement parts and watched the video to put it back together again. Read more

Removed the handle with two screws on the inside front and pulled out the custom wood panel. Pulled the compactor out from under cabinet. Tipped it over on back of unit, supporting it with a little foot stool. Unscrewed two lower screws at bottom of unit holding black trim panel (that held wood panel in place) and lower black rubber flap. Removed two screws on lower outside side of unit that held the foot pedal. Slid off black U shaped metal frame from top of compactor towards bottom. Slid on... Read more

Watched the video on how to replace. Ordered new roller, which was delivered in just a couple of days. Since the roller had broke, I was unable to roll out the refrigerator, so I tilted the refrigerator back and placed a small furniture slider under the roller frame to prevent gouging the wood floor. Then it was easy to slide out the refrigerator and replaced the roller as explained on the video. I had ordered a pin and bolt, just in case I would need to replace, but didn't need them. ... Read more

The water dispenser stopped working on my Sears Kenmore (Whirlpool) side-by-side refrigerator and after much research on the web I purchased the parts that commonly failed for this condition. I should have first taken the dispenser assembly apart but I didn't--it looked a little too intimidating to do twice. As it turns out, what actually broke was the plastic assembly that holds the water actuator switch in place so the dispenser lever could not strike it. I was able to secure it in place... Read more

Replaced the ice maker. The kit came with everything I needed to replace the ice maker. Parts that did not come with the kit were re-used from the old one. My Whirlpool refrig/freezer is an older model so the wiring harness that came with the kit was different from my existing. So instead of disconnecting the ice maker wiring harness from the freezer, I had to disconnect the harness at the ice maker. That was a b..... Anyway after about 20 minutes, finally unhooked the connector. I had... Read more

A YouTube video: https://www.youtube.com/watch?v=jIdtNdDXFDk , by a professional appliance repair company described replacement of the freezer drain pipe with Kenmore's (by Whirlpool) revised drain pipe. Ice buildup inside the freezer was caused by warm air beneath the freezer contacting cold air from inside the freezer the resulting condensation freezing and blocking the drain, causing the ice buildup inside. The revised drain tube functions as a p-trap to prevent cold/warm air interaction.... Read more

Replaced drawers with authentic parts...a perfect fit! Read more

Installed, easy peasy... Read more

Ordered a couple of shelves for our freezer and now we have room for much more in the freezer. The shelves fit as per the diagram on the appliance part pros site. Read more

Ordered Bake Element, Y04100019 (Whirlpool AP4283614) to replace a broken bake element on my 30-year old Jenn-Air Model S125 Downdraft Slide-in electric range. Received the element very quickly but it had been damaged in shipping. Called AppliancePartsPros to report this and they quickly shipped another element - very easy process. To install the element, I turned off the power to the range, put on rubber gloves (just in case) and removed the two sheet metal crews at the rear of the oven -... Read more

Lifted refrigerator in front and back. Removed roller pin holding assembly. Removed defective assembly and replaced with new. Read more

Did research on line and figured it was valve inlet part. The helpful video you provide made me realize that it was an easy job to complete. Yes it was easy because of the video and the part was exactly what was needed. We saved money by doing it ourselves. So while we were on the order site we ordered the brackets for the front grill. The old ones snapped off a long time ago. Again helpful video on your site on how to do the replacement ourselves. We now have water pressure back and that... Read more