Kenmore Washer 110.20862991 (11020862991, 110 20862991) Parts
Genuine Whirlpool part
By: Whirlpool
Part Number: WP3400516
Secures panels or brackets in your laundry center to prevent vibration noise. Replace missing, stripped, or worn screws to restore a tight fit.
Do-It-Yourself Stories from Customers like You
Gearbox replacement Dennis M. • Comer , GA • October 21, 2018
Followed online video. It was easy
Read more
More
$5.95
- Compare At:
-
$7.14
- You Save:
-
$1.19
Genuine Whirlpool part
By: Whirlpool
Part Number: WP357213
Push-in.
Do-It-Yourself Stories from Customers like You
Agitator wasnt sloshing Paige B. • Clarksville , TN • January 30, 2015
I looked inside and saw the teeth were worn off the "dogs" so I purchased the Cam Agitator repair kit and a new bolt. Getting the old bolt out was the hardest part since it was worn and rusted. I ended up having to buy a set of socket extensions and a set of stripped bolt sockets so $45 in tools and it took me an hour to get the old bolt out but putting everything back together was a breeze. I was very proud of myself, as a woman, that I fixed this problem myself and didnt have to pay a repair...
Read more
More
$5.95
- Compare At:
-
$7.14
- You Save:
-
$1.19
Genuine Whirlpool part
By: Whirlpool
Part Number: WP3360824
Fix a slipping or freely spinning top agitator with this upper auger. Restores the ratcheting motion that pulls clothes down. Quick 3-minute repair.
Do-It-Yourself Stories from Customers like You
Top agitator would not spin Daniel C. • Woodbine , MD • January 14, 2017
I have a 25 year old Kenmore washer that works well and didn't want to get a new washer as they don't make them like they used to. Upon removing the top cap of the agitator and doing an inspection, the agitator dogs were completely broken into pieces. Due to age we decided to replace the lower and upper agitator along with the agitator auger dogs repair kit. All new parts and works fine. On inspection of old parts, we probably could have gotten away with just a $5 repair for the plastic...
Read more
More
$92.25
- Compare At:
-
$108.85
- You Save:
-
$16.60
Genuine Whirlpool part
By: Whirlpool
Part Number: WP616099
This hose clamp secures a hose connection to prevent leaks and keep your appliance running smoothly. It provides a tight, reliable hold on the hose fitting so water or air stays contained during operation.
- Tightens around a hose and fitting to maintain a secure seal
- Helps stop drips, seepage, or loose connections
- Common fix when you see moisture around a hose joint
- Useful if a clamp is rusted, stretched, or no longer holding tension
What's included: One hose clamp. Install notes:
- Unplug power and shut off water (if applicable) before servicing
- Note clamp position/orientation before removal
- Use appropriate screwdriver or nut driver to tighten evenly
- Do not overtighten—ensure a snug, leak-free seal without damaging the hose
Do-It-Yourself Stories from Customers like You
Water leak Steven K. • New City , NY • August 10, 2018
Took off cover, installed new parts.
Read more
More
$9.95
- Compare At:
-
$11.59
- You Save:
-
$1.64
Genuine Whirlpool part
By: Whirlpool
Part Number: 285727
Fix a washer that won't agitate or has stripped agitator teeth. This central wash-motion component mounts to the drive hub. DIY-friendly repair.
Do-It-Yourself Stories from Customers like You
Stripped agitator neck from overloading machine John P. • Fort Myers , FL • April 30, 2016
Replaced agitator.
Read more
More
$159.54
- Compare At:
-
$188.26
- You Save:
-
$28.72
Genuine Whirlpool part
By: Whirlpool
Part Number: W11033823
Secures the door boot gasket to the front tub on front-load washers. Replace if the seal is loose or leaking during wash cycles. Confirm fit with model.
More
$8.95
- Compare At:
-
$10.65
- You Save:
-
$1.70
Genuine Whirlpool part
By: Whirlpool
Part Number: WP3356311
This screw and washer is an OEM replacement part used for Whirlpool washers. It is used to secure the lid switch. Each screw is sold individually. The screw measures approximately 1 inch.
Do-It-Yourself Stories from Customers like You
Lid safety switch had been removed and bypassed. Dale M. • Torrance , CA • June 22, 2019
Installed a new safety switch and strike. It was a very simple repair and the video described the necessary steps beautifully.
Read more
More
$5.95
- Compare At:
-
$7.08
- You Save:
-
$1.13
Genuine Whirlpool part
By: Whirlpool
Part Number: WP389386
This is the central wash-action component in select top-load washers. Replacing a worn or damaged agitator restores proper agitation so clothes circulate through water and detergent for consistent cleaning performance. What it does:
- Converts drive motion into the back-and-forth action that moves laundry
- Circulates clothes to improve soil removal and reduce tangling
- Replaces cracked, stripped, or loose agitators that cause weak or no agitation
- Common symptoms include poor cleaning, clothes not moving during wash, or an agitator that wobbles or spins freely by hand
What's included:
Install notes:
- Disconnect power and turn off water supply before servicing
- Remove the fabric softener dispenser and inner cap to access the center bolt
- Remove the bolt, lift off the old agitator, seat the new agitator on the splined shaft, and secure the bolt
- Reinstall the cap/dispenser; reuse original hardware as applicable and check for a secure fit before testing
Do-It-Yourself Stories from Customers like You
Top agitator would not spin Daniel C. • Woodbine , MD • January 14, 2017
I have a 25 year old Kenmore washer that works well and didn't want to get a new washer as they don't make them like they used to. Upon removing the top cap of the agitator and doing an inspection, the agitator dogs were completely broken into pieces. Due to age we decided to replace the lower and upper agitator along with the agitator auger dogs repair kit. All new parts and works fine. On inspection of old parts, we probably could have gotten away with just a $5 repair for the plastic...
Read more
More
$91.24
- Compare At:
-
$107.66
- You Save:
-
$16.42
Genuine Whirlpool part
By: Whirlpool
Part Number: WP62889
Used for lid switch.
Do-It-Yourself Stories from Customers like You
Washer was "dead" with a partially washed load and would not do anything Jimmy M. • Hopewell , VA • September 19, 2014
Researched this kenmore washer on-line and found the problem to be the lid switch. Saw a diagram on how to jump this switch by connecting a wire to both outside wires on the harness and voila! It worked! This is not a fix but it allowed me to finish the load of unwashed clothes and told me which part was bad (do not run washer jumped like this.......fire hazard!)
Ordered the lid switch and it was an easy repair. A $14.00 switch was a lot cheaper than a $450.00 washer. Thanks appliance parts...
Read more
More
$16.77
- Compare At:
-
$19.79
- You Save:
-
$3.02
Genuine Whirlpool part
By: Whirlpool
Part Number: WP8546455
Supports the spin basket on the center post for smooth, quiet rotation. Replace if your washer is noisy, vibrating excessively, or has poor spin performance.
More
$18.26
- Compare At:
-
$21.73
- You Save:
-
$3.47
Genuine Whirlpool part
By: Whirlpool
Part Number: WP21097
Cushioning pad that installs between the washer lid hinge and cabinet. Replace if cracked, worn, or missing to reduce squeaks and prevent metal wear.
Do-It-Yourself Stories from Customers like You
Cracked lid on a whirlpool cabrio washer Doug P. • Kansas City , MO • September 05, 2015
Removed the screws, lifted the old lid out of the hinges. Replaced the hinges, set new lid in the hinges and replaced screws.
Read more
More
$5.95
- Compare At:
-
$7.02
- You Save:
-
$1.07
Genuine Whirlpool part
By: Whirlpool
Part Number: WP3950715
White plastic insert that snaps into your washer's control knob. Restores a clean, finished appearance when the original is cracked, discolored, or missing.
More
$49.40
- Compare At:
-
$59.28
- You Save:
-
$9.88
Genuine Whirlpool part
By: Whirlpool
Part Number: WP3355454
Replace your washer's anti-rattle clip to eliminate vibration noise and buzzing during cycles. Secures components with light spring tension. Confirm fit with your model number before ordering.
Do-It-Yourself Stories from Customers like You
My washer wouldn't go into a spin cycle. Joshua P. • Cohutta , GA • April 18, 2021
I bought a clutch liner kit installed it in 5 minutes now it spins faster than ever.
Read more
More
$5.95
- Compare At:
-
$7.08
- You Save:
-
$1.13
Genuine Whirlpool part
By: Whirlpool
Part Number: WP3357319
Hose used from Valve to thermistor.
More
$18.42
- Compare At:
-
$21.92
- You Save:
-
$3.50
Genuine Whirlpool part
By: Whirlpool
Part Number: WP16123
Rubber washer gasket for washer fill hose connections. Replace if worn or leaking at coupler adapter. Measures 1-1/16 x 5/8 inch. Verify fit with model.
Do-It-Yourself Stories from Customers like You
Water inlet valve was corroded and broken washer Sandra H. • Belton , MO • June 26, 2015
Replaced with new part ordered from store
Read more
More
$5.95
- Compare At:
-
$7.02
- You Save:
-
$1.07
Genuine Whirlpool part
By: Whirlpool
Part Number: W10846509
The Screw is an OEM component compatible with Whirlpool washing machines. This screw secures the rear bulkhead to the tub, ensuring vibrations are reduced through solid mounting points. Properly installed screws dampen oscillating movement.
Causes of a bad screw include damage from water exposure like corrosion or breakage from stress concentrations if the tub bangs around during imbalanced loads.
Symptoms of a bad screw include:
- Loose or detached rear bulkhead allowing side-to-side play
- Excessive noise and shaking felt through the surrounding walls
- Development of micro-cracks around screw holes over time
- Potential leak paths if holes are no longer sealed
This Whirlpool replacement screw restores a stable suspension system. It is compatible with additional brands like Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.
Do-It-Yourself Stories from Customers like You
The drum was off center and tilted forward right and water was pouring on the floor William T. • Farmingdale , NY • December 22, 2015
Springs were broken and back bracket was bent I replaced the bracket and all four Springs including the vertical one. I removed the cabinet as shown in the video. Then with a pair of vise grips's removed the springs one by one and replace them. The bracket was rusted And bent i used a quarter inch socket with a quarter inch ratchet to remove the screw. Due to the rust i used penetrating oil the screw.
Read more
More
$5.95
- Compare At:
-
$7.02
- You Save:
-
$1.07