Kenmore Washer 110.24722300 (11024722300, 110 24722300) Parts
Genuine Whirlpool part
By: Whirlpool
Part Number: WP3400516
Secures panels or brackets in your laundry center to prevent vibration noise. Replace missing, stripped, or worn screws to restore a tight fit.
Do-It-Yourself Stories from Customers like You
No spin on spin cycle Richard S. • Beaumont , CA • August 28, 2015
Replaced clutch assembly which was a little tricky, but very doable. Just make sure to take your time. I do have to say that I am very impressed with AppliancePartsPro customer service when the replacement part also failed. A new clutch assembly was at my door step a few days later. I now has a working washer again. Thanks Again Appliance Parts Pro.
Read more
More
Genuine Whirlpool part
By: Whirlpool
Part Number: WP8542050
Fix a washer that won't advance cycles or spin with a new timer. Controls wash, rinse, and spin phases. Common DIY repair with clear instructions.
Do-It-Yourself Stories from Customers like You
We diagnosed it as failure in the timer Barbara S. • Columbia , MO • February 16, 2015
Ordered the timer. Amazed in arrived in less that 24 hours. Reviewed the video with instructions twice and removed the old timer and replaced with the new. Working fine now. Only problem encountered was the washer used in the repair video was somewhat difference from ours. Easy to adapt to it and could identify the differences.
Read more
More
Genuine Whirlpool part
By: Whirlpool
Part Number: WP616099
This hose clamp secures a hose connection to prevent leaks and keep your appliance running smoothly. It provides a tight, reliable hold on the hose fitting so water or air stays contained during operation.
- Tightens around a hose and fitting to maintain a secure seal
- Helps stop drips, seepage, or loose connections
- Common fix when you see moisture around a hose joint
- Useful if a clamp is rusted, stretched, or no longer holding tension
What's included: One hose clamp. Install notes:
- Unplug power and shut off water (if applicable) before servicing
- Note clamp position/orientation before removal
- Use appropriate screwdriver or nut driver to tighten evenly
- Do not overtighten—ensure a snug, leak-free seal without damaging the hose
Do-It-Yourself Stories from Customers like You
Water leak Steven K. • New City , NY • August 10, 2018
Took off cover, installed new parts.
Read more
More
Genuine Whirlpool part
By: Whirlpool
Part Number: WP389387
Agitator won't move or slips during wash? A worn drive shaft causes weak agitation. This shaft transfers motion from the gearcase to restore firm engagement.
Do-It-Yourself Stories from Customers like You
Agitator was not turning Edward M. • Glen Allen , VA • March 10, 2019
I had to replace the drive shaft and the lower agitator. The motor coupling was also worn out. The repair was challenging because I had to rebuild the gear box. This step was really messy and I had to wait for the liquid gasket to set prior to completing the repair. Cleaning and prep of all of the parts tripled the repair time.
Read more
More
Genuine Whirlpool part
By: Whirlpool
Part Number: WP357213
Push-in.
Do-It-Yourself Stories from Customers like You
Agitator wasnt sloshing Paige B. • Clarksville , TN • January 30, 2015
I looked inside and saw the teeth were worn off the "dogs" so I purchased the Cam Agitator repair kit and a new bolt. Getting the old bolt out was the hardest part since it was worn and rusted. I ended up having to buy a set of socket extensions and a set of stripped bolt sockets so $45 in tools and it took me an hour to get the old bolt out but putting everything back together was a breeze. I was very proud of myself, as a woman, that I fixed this problem myself and didnt have to pay a repair...
Read more
More
Genuine Whirlpool part
By: Whirlpool
Part Number: WP8055141
Supports the driven cam in your washer's drive assembly, reducing friction for smooth operation. Replace if you notice grinding noises or cycle issues.
Do-It-Yourself Stories from Customers like You
Shaking / very unbalanced during spin cycle Dale B. • Geneseo , IL • June 11, 2017
Watched your videos on repairing different parts of the washer such as, the tub, agitator, tub balance springs. The problem was found when I removed the agitator. The neck of the tub was almost totally rusted through. Had I had a spanner wrench it would have been a lot easier. Several sprays with GP Blaster penetrating oil helped loosen the nut but punch and hammer damaged the nut to where I didn't want to reuse it. Next problem was getting the basket drive block and tub loose from the gearbox...
Read more
More
Genuine Whirlpool part
By: Whirlpool
Part Number: W11033823
Secures the door boot gasket to the front tub on front-load washers. Replace if the seal is loose or leaking during wash cycles. Confirm fit with model.
More
Genuine Whirlpool part
By: Whirlpool
Part Number: WP3356311
This screw and washer is an OEM replacement part used for Whirlpool washers. It is used to secure the lid switch. Each screw is sold individually. The screw measures approximately 1 inch.
Do-It-Yourself Stories from Customers like You
Replaced lid switch needed screws Niema S. • Sykesville , MD • March 16, 2017
Replaced lid switch with new part.
Read more
More
Genuine Whirlpool part
By: Whirlpool
Part Number: WP8546455
Supports the spin basket on the center post for smooth, quiet rotation. Replace if your washer is noisy, vibrating excessively, or has poor spin performance.
More
Genuine Whirlpool part
By: Whirlpool
Part Number: WP62889
Used for lid switch.
Do-It-Yourself Stories from Customers like You
Washer was "dead" with a partially washed load and would not do anything Jimmy M. • Hopewell , VA • September 19, 2014
Researched this kenmore washer on-line and found the problem to be the lid switch. Saw a diagram on how to jump this switch by connecting a wire to both outside wires on the harness and voila! It worked! This is not a fix but it allowed me to finish the load of unwashed clothes and told me which part was bad (do not run washer jumped like this.......fire hazard!)
Ordered the lid switch and it was an easy repair. A $14.00 switch was a lot cheaper than a $450.00 washer. Thanks appliance parts...
Read more
More
Genuine Whirlpool part
By: Whirlpool
Part Number: WP3950715
White plastic insert that snaps into your washer's control knob. Restores a clean, finished appearance when the original is cracked, discolored, or missing.
More
Genuine Whirlpool part
By: Whirlpool
Part Number: WP3947517
If your washer agitator spins freely or clothes aren't agitating properly, this assembly restores the back-and-forth motion. DIY repair in 10-30 minutes.
Do-It-Yourself Stories from Customers like You
The agitator wasn't spinning Gerald B. • Anaheim Hills , CA • December 22, 2018
The bolt that holds the agitator and the agitator cam was rusted in place so it made the project way more difficult than it should have been. Had to cut the agitator off the shaft and cut the head of the frozen bolt off. Thankfully, Appliance Pros had all three parts I needed. Once the parts arrived it only took ten minutes to fix. Since the house was going to be full for Christmas, the fast shipping really, really helped. Was able to get it done before the guests arrived.
Read more
More
Genuine Whirlpool part
By: Whirlpool
Part Number: WP3355454
Replace your washer's anti-rattle clip to eliminate vibration noise and buzzing during cycles. Secures components with light spring tension. Confirm fit with your model number before ordering.
Do-It-Yourself Stories from Customers like You
My washer wouldn't go into a spin cycle. Joshua P. • Cohutta , GA • April 18, 2021
I bought a clutch liner kit installed it in 5 minutes now it spins faster than ever.
Read more
More
Genuine Whirlpool part
By: Whirlpool
Part Number: WP2172937
This three-circuit connector housing organizes and protects terminals in an appliance wiring harness. It provides a secure, insulated plug connection to help prevent loose contacts, heat damage, and intermittent operation when the original housing is cracked or melted. What it does:
- Holds three wiring terminals in the correct orientation for a mating connector
- Insulates and locks terminals to reduce arcing and overheating at the plug
- Replaces cracked, brittle, or heat-damaged connector housings
- Symptoms can include intermittent power, burnt odor near the connector, discoloration/melting, or a plug that won't stay latched
What's included:
- 1 three-circuit connector housing
Install notes:
- Disconnect power before servicing the appliance
- Note wire/terminal positions and transfer them one at a time into the new housing
- Inspect terminals; replace any that are discolored, loose, or damaged. Use the correct crimp tool/terminals specified for your model
- Fully seat each terminal until it locks and the connector latch engages securely
More
Genuine Whirlpool part
By: Whirlpool
Part Number: WP16123
Rubber washer gasket for washer fill hose connections. Replace if worn or leaking at coupler adapter. Measures 1-1/16 x 5/8 inch. Verify fit with model.
Do-It-Yourself Stories from Customers like You
Water inlet valve was corroded and broken washer Sandra H. • Belton , MO • June 26, 2015
Replaced with new part ordered from store
Read more
More
Genuine Whirlpool part
By: Whirlpool
Part Number: WP54583
Right hand side. For screws use WPW10119828.
Do-It-Yourself Stories from Customers like You
Whirlpool washer David L. • Linn , MO • August 31, 2015
With the parts supplied from your company. The lady that took my order was good at her job. All the parts were correct and fit. I thank you for the service that recieved.
Read more
More