Kenmore Washer 110.27062602 (11027062602, 110 27062602) Parts

The Washer Lid Screw is an OEM part for Whirlpool washing machines. This 6-32 x .340 screw secures the washer lid to the hinge assembly, ensuring the lid opens and closes smoothly and stays securely in place during operation.

Causes of a bad washer lid screw can include wear and tear from frequent use, corrosion due to exposure to moisture, or damage from over-tightening or mishandling. A compromised screw can lead to issues with the lid's stability and functionality.

Symptoms of a bad washer lid screw include:

• The washer lid feeling loose or wobbling
• Difficulty in opening or closing the lid
• Visible rust or corrosion on the screw
• The lid not staying securely in place

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This is a clear plastic hose that runs from the water level switch to the bottom of the tub.

The Water Level Pressure Switch Hose is an OEM part for Whirlpool washers, playing a critical role in the accurate measurement of water levels within the machine.  

Causes of damage to the Water Level Pressure Switch Hose can stem from natural wear and tear over time, leading to cracks or holes in the hose. 

Symptoms of a bad Water Level Pressure Switch Hose include:

• The washer overfills or underfills, indicating a problem with water level detection.
• Unusual noises during the fill cycle, which may suggest air leaks in the hose.
• Error codes related to water level or filling issues displayed on the washer.
• The machine stops mid-cycle due to incorrect water level readings.

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

The Tub to Circulation Pump Hose is an OEM replacement part for Whirlpool washing machines. This hose provides a direct connection between the tub and circulation pump during wash cycles. The hose is responsible for transporting water from the tub to the circulation pump and spinning basket assembly.

Causes of a bad tub to circulation pump hose can include cracking, kinking or collapse of the inner lining. Wear and environmental factors like mineral buildup can weaken it over time.

Symptoms of a bad hose include:

• Water leaks within or around the washing machine
• The washer fails to fill or drain properly
• Reduced water pressure impacting cleaning performance

This genuine OEM Whirlpool part is compatible with brands like Maytag, KitchenAid, and more, it ensures long-lasting performance.

This 8-18 x 5/8-inch screw secures appliance panels, brackets, and covers. Replacing a missing or stripped fastener restores a tight fit and helps prevent vibration or loosening where this exact size is specified.

• Fastens sheet-metal or plastic components where a #8-18 x 5/8 screw is called for
• Helps maintain alignment and reduce rattling or vibration
• Replaces stripped, corroded, or missing screws of the same size
• Common symptoms: loose panels, gaps/poor fit, rattling noises, or visible missing hardware

• Disconnect power and shut off gas/water (as applicable) before service
• Match thread and length to the original; replace screws one at a time to keep parts aligned
• Start threads by hand to avoid cross-threading; tighten snugly without overtightening
• If the receiving threads are damaged, additional repair (clip, insert, or new nut) may be needed

Size: 5 foot long. Rubber fill hose used on most automatic washing machines. Two hoses used per machine.

This replacement screw secures panels, brackets, and other components in your appliance to keep them aligned and rattle-free. Replacing worn, stripped, or missing hardware restores a tight fit and helps maintain safe, quiet operation.

• Fastens panels, brackets, or internal parts to the cabinet/frame
• Helps maintain alignment to reduce vibration and rattling
• Replaces lost, stripped, or corroded screws
• Common symptoms: loose panels/trim, rattles, or a screw that won't tighten

• Disconnect power; shut off water or gas if applicable
• Match thread and length to the original; replace one at a time to keep alignment
• Start threads by hand to avoid cross-threading; use the correct driver
• Tighten snugly—do not overtighten, especially into plastic or thin sheet metal

Specs: 10-16 x 1/2 inch.

When replacing this part, if you see that your motor stator is broken, search by your model number to make sure you get the right stator for your model. NOTE: Also includes Rotor Bolt. The bolt is not available separately.

This fresh-water nozzle assembly directs a controlled stream into the appliance during fill/dispense. Replacing a cracked or clogged nozzle restores proper flow and helps reduce splashing, misdirected spray, or dripping at the opening. What it does:

• Shapes and directs fresh water into the tub/dispenser area
• Helps prevent spray, backflow, and mess around the opening
• Common symptoms: weak or misdirected stream, dripping after fill/dispense, leaks near the opening, visible cracks or mineral buildup on the nozzle
• A kinked or brittle attached tube can restrict flow or leak

• One fresh-water nozzle assembly

• Disconnect power and shut off the water supply before servicing
• Access the nozzle area; remove necessary panels or trim
• Release retaining clip(s), disconnect tubing, and note routing before removal
• Install the new assembly fully seated; restore water/power, check for leaks, and run a test fill to flush air/debris

This washer impeller mounts at the bottom of the tub to generate the water currents that move and roll garments during the wash cycle. Replacing a cracked or stripped impeller restores proper turnover and cleaning performance.

• Creates the wash action by circulating water and moving fabrics through the load
• Secures to the drive hub; worn splines or a damaged center can cause slippage
• Common symptoms: poor cleaning, clothes not moving during wash, clicking/grinding from the wash plate area, visible cracks or looseness
• Direct replacement for the low-profile agitator "wash plate" style

• Disconnect power and turn off water supply before servicing
• Remove the center cap and retaining screw/bolt; lift the old impeller straight up
• Clean the hub splines; seat the new impeller fully and tighten the fastener securely
• Avoid prying against the tub; test on a short cycle to ensure proper wash action

Small but essential, this drain hose retainer is a clip that secures the hose in place during use or storage. It keeps the hose properly routed to help prevent kinks, pull-outs, and leaks. What it does:

• Holds the drain hose to the cabinet/frame for correct routing or stowage
• Helps prevent kinks, abrasion, and strain that can cause poor draining or leaks
• Replaces a broken, warped, or missing retainer so the hose stays put
• Common symptoms: hose won't stay clipped, falls during operation, visible damage, water near hose path

• 1 drain hose retainer

• Disconnect power and turn off the water supply before servicing
• Access the hose routing area and remove the damaged retainer
• Position and fasten the new retainer in the same location; route the hose through it
• Run a brief test to ensure secure routing and no leaks

This recirculation hose routes wash water back through the tub during the cycle. A fresh, intact hose helps maintain proper water flow and prevents leaks, supporting consistent cleaning performance.

• Directs water from the pump back into the tub for continued circulation
• A cracked, kinked, or leaking hose can cause water leaks or poor wash performance
• Can help resolve issues like low recirculation flow or visible water drips during operation
• Restores correct internal water routing as designed

• Disconnect power and water supply before servicing
• Have towels or a shallow pan ready to catch residual water
• Note hose routing and clamp positions before removal; reuse or replace clamps as needed
• After installation, run a quick cycle to check for leaks and proper flow

This lid hinge pad fits between the washer lid hinge and the cabinet. It cushions the joint to reduce squeaks and metal wear, helping keep the lid aligned and operating smoothly.

• Provides a protective wear surface between the hinge and cabinet/lid
• Reduces squeaks, creaks, and rattling when opening or closing the lid
• Helps maintain proper lid alignment and smooth movement
• Common signs it's worn or missing: squeaking lid, rubbing/scuff marks at the hinge, loose or wobbly lid

• Disconnect power to the washer before servicing
• Support the lid to relieve hinge tension and access the hinge area per your model
• Remove the worn pad and press the new pad fully into the hinge location
• Test lid operation; inspect the opposite hinge and replace its pad as needed if your model uses two

Size: 1/4 inch hex head, 10-12 x 1/2 inch.

This hose clamp secures a flexible hose to its fitting to help prevent leaks and hose blow-offs during operation. Replace a rusted, stripped, or distorted clamp to restore a tight, reliable seal at the connection point.

• Applies clamping force around a hose to hold it on a barb or stub fitting
• Commonly used on washer drain and tub-to-pump hose connections
• Helps stop drips at the joint and prevents the hose from slipping off
• Typical failure signs: leaking at the connection, clamp won't tighten, visible rust, broken/warped band

• Unplug the appliance and turn off water supply; expect some residual water
• Seat the hose fully on the fitting; place the clamp just behind the bead/barb
• Tighten until snug and secure; do not overtighten to avoid damaging the hose
• Run a short test cycle and recheck for leaks at the connection

This hose clamp secures dishwasher hoses to fittings and ports to maintain a tight, leak-resistant seal. Replacing a worn clamp helps prevent drips and loose connections that can cause water under the unit.

• Secures drain or circulation hose to the pump, sump, or other dishwasher fittings
• Helps maintain a watertight seal at hose connection points
• Can help resolve water dripping from a hose joint or a loose hose
• Replace if corroded, deformed, cracked, or no longer holds tension

• Disconnect power and turn off the water supply before servicing
• Place a towel or shallow pan to catch residual water when removing hoses
• Fully seat the hose on the fitting, position the clamp over the barb/connection, and secure firmly
• After reassembly, run a brief fill/drain and check all connections for leaks