Kenmore Washer 110.28322700 (11028322700, 110 28322700) Parts
Genuine Whirlpool part
By: Whirlpool
Part Number: WP89503
Size: 5 foot long. Rubber fill hose used on most automatic washing machines. Two hoses used per machine.
Do-It-Yourself Stories from Customers like You
Low water flow and fabric softener would dispense immediately when cycle started Bob G. • Sylacauga , AL • January 19, 2019
Replaced flow meter and control valve
Read more
More
$18.59
- Compare At:
-
$22.12
- You Save:
-
$3.53
Genuine Whirlpool part
By: Whirlpool
Part Number: WP62750
The Whirlpool spacer is an OEM replacement part responsible for maintaining the proper spacing and alignment between the washer cabinet and the top panel. The spacer provides stability and support to the appliance. It ensures that the top panel is securely attached and evenly distributed, preventing any misalignment or instability during operation.
Causes of a bad spacer can include wear and tear over time, physical damage due to accidental impacts, or deformation from prolonged use under stress. These issues can lead to misalignment and operational inefficiencies in the appliance.
Symptoms of a bad spacer include:
- Misalignment of components
- Unusual noises during operation
- Difficulty in assembling or disassembling parts
- Reduced efficiency of the appliance
This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.
Sold individually, four are needed to replace all parts. Screw part number WP3390631.
More
$5.95
- Compare At:
-
$7.08
- You Save:
-
$1.13
Genuine Whirlpool part
By: Whirlpool
Part Number: WP3359452
This locking nut is used for many purposes on a range of machines including household appliances. This nut is often used for leg leveling for machines. It will help with vibrations from washers and dryers. If the nut is used for this purpose and goes missing or becomes damaged, it could cause the machine to vibrate more and seem louder.Nuts are made from metal and are built to last a long time. However, there can still be issues that arise. In some cases, the nuts might go missing if they become loose and the machine is moved. They could also corrode over time and need to be replaced. The replacement of the nut is typically a fast and simple repair.The nut is a genuine OEM replacement part sourced from the manufacturer. It can work with washers, dryers, and combo machines, and is compatible with models from Whirlpool, Kenmore, Maytag, and Roper. The part is sold individually. Owners may want to have several on hand.
Do-It-Yourself Stories from Customers like You
Whirlpool washer was shaking and moving in spin cycle Charles B. • Sioux Falls , SD • September 25, 2018
Replaced 2 springs and brackets. Also replace rear legs and front legs and re leveled. Works fine.
Read more
More
$5.95
- Compare At:
-
$7.14
- You Save:
-
$1.19
Genuine Whirlpool part
By: Whirlpool
Part Number: WP3390631
10 - 16 x 1/2
Do-It-Yourself Stories from Customers like You
Agitator wasnt sloshing Paige B. • Clarksville , TN • January 30, 2015
I looked inside and saw the teeth were worn off the "dogs" so I purchased the Cam Agitator repair kit and a new bolt. Getting the old bolt out was the hardest part since it was worn and rusted. I ended up having to buy a set of socket extensions and a set of stripped bolt sockets so $45 in tools and it took me an hour to get the old bolt out but putting everything back together was a breeze. I was very proud of myself, as a woman, that I fixed this problem myself and didnt have to pay a repair...
Read more
More
$7.31
- Compare At:
-
$8.70
- You Save:
-
$1.39
Genuine Whirlpool part
By: Whirlpool
Part Number: WP62691
Rubber grommet for motor mount stud.
Do-It-Yourself Stories from Customers like You
Washer did not agitate Gary S. • Kimberling City , MO • December 26, 2016
Replaced dog ears.
Read more
More
$8.95
- Compare At:
-
$10.56
- You Save:
-
$1.61
Genuine Whirlpool part
By: Whirlpool
Part Number: WP62658
Washer thrust ring acts as a bearing spacer between the outer tub and basket drive, controlling end-play and reducing friction. Replace when worn to restore smooth, quiet operation and prevent premature wear.
Do-It-Yourself Stories from Customers like You
Washer driver block was worn out Melissa J. • Battle Creek , MI • March 15, 2015
Purchased parts from your site and did a self repair. Excellent quality , speedy delivery and easy to install. Now our 13 year old washer works as good as new.
Read more
More
$8.95
- Compare At:
-
$10.65
- You Save:
-
$1.70
Genuine Whirlpool part
By: Whirlpool
Part Number: W10880720
Replaces the upper tub ring that mounts on top of the outer tub as a splash guard. Order a new ring if yours is cracked, broken, or no longer securely attached.
Do-It-Yourself Stories from Customers like You
Excessive vibration during spin cycle Jackie H. • Dunbar , WV • September 10, 2018
This was the second attempt at fixing this problem. The first repair and parts were generated by listing the problem and reviewing the potential corrections, listed on the web site. From making repairs on other clothes washers, I was confident that some of those potential causes could have been the cause. Unfortunately the counterbalance spring and suspension springs were not the cause as they were attached as intended and in good condition.
I reached out for Appliance Parts Pros input...
Read more
More
$94.95
- Compare At:
-
$112.99
- You Save:
-
$18.04
Genuine Whirlpool part
By: Whirlpool
Part Number: 63849
Replace your washer's cracked or leaking outer tub. This housing holds the inner basket and prevents water from leaking into the machine's interior.
Do-It-Yourself Stories from Customers like You
Outer tub cracked Brian H. • North Tonawanda , NY • February 06, 2015
Replaced tub and center post seal
Read more
More
$230.95
- Compare At:
-
$256.32
- You Save:
-
$25.37
Genuine Whirlpool part
By: Whirlpool
Part Number: W10820044
Replacement power cord that connects your washer to the wall outlet. Includes strain relief for cable protection. Needed when original cord is damaged, pinched, shorted, or worn. Direct plug-in installation.
Do-It-Yourself Stories from Customers like You
Power cord got pinched and shorted out Gary D. • Kentwood , MI • July 27, 2014
Bought a new cord and removed the back of the washer and unclipped the old and clipped in the new. 5 minutes tops.
Read more
More
$78.95
- Compare At:
-
$93.95
- You Save:
-
$15.00
Genuine Whirlpool part
By: Whirlpool
Part Number: WP358912
Cap seal creates a tight barrier between cap and mating surface to prevent leaks. Replace when worn or damaged to restore secure fit. Confirm compatibility.
Do-It-Yourself Stories from Customers like You
Not spinning Jerry A. • Bohemia , NY • October 11, 2016
Thank you for your video on web site , had no problem replacing clutch
Read more
More
$15.95
- Compare At:
-
$17.14
- You Save:
-
$1.19
Genuine Whirlpool part
By: Whirlpool
Part Number: 285353
This retainer ring is a genuine OEM replacement part sourced directly from the manufacturer for use on front load washing machines to hold the boot seal in place. The boot seal is the gasket that seals the washing machine when the door is closed to prevent water from leaking. The retainer ring is located flush against the boot seal and has either a spring clamp or screw clamp that secures it. Over time, this ring may become damaged due to the washing machine's normal use and age. If the ring is not tight, the washing machine could leak when in use. If water is coming from the door, it is a good idea to inspect and replace the retainer ring and possibly the boot as well.Unplug the washing machine to prevent electrocution. Remove the front panel, the detergent dispenser, and the kickplate to access the retainer ring. Locate the clamp on the ring and loosen it. Remove the retainer ring and set it to the side. Inspect the boot and then install the new retainer ring. Tighten the clamp and reassemble the washing machine. This retainer ring is sold as an individual unit. It is designed specifically for washing machines manufactured by Whirlpool.
Do-It-Yourself Stories from Customers like You
Washer would agitate but would not go into high spin sounded like spin was working though Mario M. • Corona , CA • January 03, 2015
Im not a repairman, so all my knowledge to fix my washer came from either youtube or online chats. I posted this to help the next dad trying to save a few bucks.
Door sensor...
Since door sensor worked correctly, verified that by starting washer with door open, and agitate cycle would not start until door was closed. Meaning door sensor worked correctly.
Timer...
In high spin cycle washer sounded correcltly spinning, but when opening door, drum was was not moving. So timer was triggering...
Read more
More
$5.95
- Compare At:
-
$7.02
- You Save:
-
$1.07
Genuine Whirlpool part
By: Whirlpool
Part Number: WP8578340
This water inlet valve controls the flow of household water into the dishwasher at the start of a cycle. Replacing a weak, stuck, or leaking valve restores proper filling performance and helps prevent fill-related errors and leaks. What it does:
- Opens and closes electrically to regulate water entering the dishwasher
- Helps ensure correct fill level and timing for each cycle
- Common failure symptoms: won't fill or slow fill, water seeping into tub when off, external leak at valve connections, loud buzzing/chattering during fill
- May set fill or water supply-related error codes on some models
What's included:
- 1 water inlet valve assembly
Install notes:
- Disconnect power and turn off the water supply before servicing
- Have a towel or shallow pan ready for residual water when removing lines
- Transfer any original mounting hardware or fittings from the old valve as needed
- Inspect/clean the inlet screen and flush the supply line; check all connections for leaks after installation
This part fixes the following symptoms
-
No hot or cold water
-
Will not stop filling with water
-
Will not fill with water
See more...
Do-It-Yourself Stories from Customers like You
Water would not stop running into washer. Gary M. • Ionia , MI • March 17, 2014
Ordered this part and just changed it out. Not hard once I figured out how to get in to it.
Read more
More
$131.49
- Compare At:
-
$156.47
- You Save:
-
$24.98
Genuine Whirlpool part
By: Whirlpool
Part Number: WPW10086010
Secures the motor to its mounting point in your laundry center. Replace if the retainer is worn, broken, or has lost tension to prevent motor misalignment.
Do-It-Yourself Stories from Customers like You
The drive coupler was wore out upon fixing noticed clips were rusty and lost tension and start capacitor was badly corroded James H. • Waterloo , IA • February 03, 2017
Replaced with new retainer clips and new capacitor to fix future problems
Read more
More
$5.95
- Compare At:
-
$7.08
- You Save:
-
$1.13
Genuine Whirlpool part
By: Whirlpool
Part Number: WP3400516
Secures panels or brackets in your laundry center to prevent vibration noise. Replace missing, stripped, or worn screws to restore a tight fit.
Do-It-Yourself Stories from Customers like You
Gearbox replacement Dennis M. • Comer , GA • October 21, 2018
Followed online video. It was easy
Read more
More
$5.95
- Compare At:
-
$7.14
- You Save:
-
$1.19
Genuine Whirlpool part
By: Whirlpool
Part Number: WP3360824
Fix a slipping or freely spinning top agitator with this upper auger. Restores the ratcheting motion that pulls clothes down. Quick 3-minute repair.
Do-It-Yourself Stories from Customers like You
Top agitator would not spin Daniel C. • Woodbine , MD • January 14, 2017
I have a 25 year old Kenmore washer that works well and didn't want to get a new washer as they don't make them like they used to. Upon removing the top cap of the agitator and doing an inspection, the agitator dogs were completely broken into pieces. Due to age we decided to replace the lower and upper agitator along with the agitator auger dogs repair kit. All new parts and works fine. On inspection of old parts, we probably could have gotten away with just a $5 repair for the plastic...
Read more
More
$92.25
- Compare At:
-
$108.85
- You Save:
-
$16.60
Genuine Whirlpool part
By: Whirlpool
Part Number: WP8546681
Washer won't advance cycles or stops mid-cycle? This timer sequences fill, wash, drain, and spin stages. Moderate DIY repair restores cycle control.
Do-It-Yourself Stories from Customers like You
Wouldn't complete cycle, finish rinsing David H. • Corpus Christie , TX • April 08, 2014
Watched instructional viedeos on how to replace timer.
Read more
More
$184.77
- Compare At:
-
$221.72
- You Save:
-
$36.95