Kenmore Washer 110.46752701 (11046752701, 110 46752701) Parts

• Marks left on clothes

Searching for paddles or baffles led me to Appliance Parts. Discovered I didn't have to buy anything in order to view the video which is a pretty nice feature to see if my skills are up to it. "How in the world do I repair something without external screws?" "Take the top off the machine to see if there are any mounting screws and then just smack the baffles toward the rear of the machine with a mallet to loosen and remove?" Easy, really easy. My wife was missing an underwire to one of her bras... Read more

Prior to ordering parts I had pulled the pump strainer basket and cleaned it out. There was both soft and hard scale build up. The tub-to-pump hose was also pretty crusty/slimey. Still got warnings for SUDS and repeated F02 errors. Ordered parts and replaced the pump, tub-to-pump hose, interior drain hose and exterior drain hose (both hoses has some slime build up). The water standing in the tub when I emptied it the first time had very little suds but we kept getting the SUDS warning. ... Read more

• Won't start

Replace the water temperature sensor and still had the error code. While I had the back of the machine open I ran the washer. I traced the black wires from the temperature sensor and wiggled them as the washer was running. At one zip tie every time i moved the wires the washer would stop running and the error code would flash. Sure enough, like many others posted, the vibration from the machine had split the wire. I spiced the wire back together and have not had a problem since. Read more

Several months back, I checked the supply hoses and replaced the hot water hose because of corrosion. The cold water hose was fine. I replaced the water inlet valve and that seemed to fix the problem, but after about a week, the problem resurfaced. After searching various internet resources, I though the pressure switch which detects the water level could be bad. I order both the pressure switch and the hose that connects it to the air chamber. Before installing the new pressure switch, I... Read more

This was actually one of the easiest fixes I’ve done. All that was required was to remove 3 screws to remove the broken part. I used a pair of pliers to remove the moisture sensors from the broken part to the new one. Read more

• Leaking

We ordered parts from appliance parts pros and I fixed it. Read more

I pulled the unit away from the wall and noticed black dust on the floor. Unplugged the unit, turned off the water. Removed back panel (about 10 screws with Torx heads) and noticed the belt was off, the drive pulley was loose and wobbling on the shaft, black dust all over the inside. Belt was worn along one side. Some grooves/damage in the outer drum casing around the pulley where it appeared the belt had rubbed. Removed the lower crossbar (2 more screws) to get better access to the drive... Read more

Water became visible as it accumulated at the bottom rear part (the part that is tilted back) of the washer drum. I theorized that the valve controlling water flow into the machine was to blame. I began my troubleshooting by going to Appliance Pros website where I looked for a Water Inlet Valve. I easily found this on the exploded parts diagram. After identifying the part that seemed to be the issue, I began reading other reviews from folks who were experiencing the same problem and who solved... Read more

• Won't start

I was searching the web for solutions and came across two folks who had similar trouble code. One fixed his by removing the pump strainer from the pump to find coins blocking water flow, thus the analog water pressure sensor provided a failure response. My issue was solved by following the other hints I got. I ordered a new sensor (switch). It was expensive for what it is, but the washer will not run correctly without it! The part arrived in a very timely manner, and it was the right part.... Read more

After much reading on line regarding my problem. I decided to do any test that I could to try to diagnose and fix this myself if I could. This took a lot of time and patience to get the answers on how to go about this from "experts" as some of the info was contradictory. I was almost about to give up and buy a new washer with less electronic parts and buttons as advised by an honest appliance technician . I tried one more thing first which was to disconnect the lead wires connected to the MCU .... Read more

Prior to ordering parts I had pulled the pump strainer basket and cleaned it out. There was both soft and hard scale build up. The tub-to-pump hose was also pretty crusty/slimey. Still got warnings for SUDS and repeated F02 errors. Ordered parts and replaced the pump, tub-to-pump hose, interior drain hose and exterior drain hose (both hoses has some slime build up). The water standing in the tub when I emptied it the first time had very little suds but we kept getting the SUDS warning. ... Read more

Replaced flow meter and control valve Read more

The replaced hose from the dispenser and o-ring problem fixed. Read more

The shipping bolts came in 2 days!!! Wow ! So we watched a video on how to install them and moved the washer without messing it up.. Thank you so much for fast and friendly service :-) Read more

I ordered a stack kit according to the model numbers on the washer and dryer and the kit worked perfectly. My washer and dryer are now stacked and I am extremely satisfied with how easy it was to order from this website and the quick delivery of my part. Thank you! Read more