Kenmore Dryer 110.60972990 (11060972990, 110 60972990) Parts

This door spring counterbalances your dishwasher door so it opens and closes smoothly without slamming. Replacing a fatigued or broken spring restores proper tension and helps protect the hinges and latch.

• Provides counterbalance tension to the door through the hinge mechanism
• Helps the door open and close with controlled movement and stay in position
• Symptoms of failure can include a door that drops quickly, feels heavy, or won't stay put
• May also cause popping/squeaking noises or uneven action on one side of the door

• Disconnect electrical power and turn off the water supply before servicing
• Remove the toe panel/kick plate to access springs near the hinges
• Carefully relieve and reattach spring tension; wear gloves and eye protection
• Ensure both sides are tensioned evenly after replacement

Restore smooth operation of your dryer's lint screen cover with this lint screen door spring. It provides the correct tension so the cover opens and closes properly and the lint screen seats securely for reliable lint collection.

• Applies spring tension to the lint screen door/cover hinge
• Helps the lint screen and cover stay properly positioned
• A worn or broken spring may cause the cover to feel loose, pop open, or not stay closed
• May make inserting or removing the lint screen difficult

• Disconnect power; for gas dryers, also shut off gas supply
• Access the lint screen door area per your model's service information
• Note the original spring orientation; transfer the new spring carefully using needle-nose pliers
• Check cover operation and lint screen seating before restoring power

Color: Almond

The lid switch lever connects the washer's lid hinge to the lid switch, signaling when the lid is closed so the cycle can run. A damaged lever can prevent the safety interlock from closing, leading to no-start or spin issues. What it does:

• Transfers lid movement at the hinge to the lid switch actuator
• A closed lid so the washer can operate
• Common symptoms of a failed lever: washer won't start; won't spin; cycle pauses because the lid-closed signal isn't detected

• 1 lid switch lever

• Disconnect power before servicing
• Lift or open the top to access the hinge/switch area; locate the lever near the lid switch
• Remove the old lever and install the new one in the same orientation; free movement
• Close the lid by hand and the switch clicks before reassembly and testing

This dryer blower cover encloses the blower wheel and seals the housing so air moves efficiently from the lint screen to the exhaust. Replacing a cracked or missing cover restores airflow for consistent drying performance and helps keep lint contained.

• Covers the blower wheel and seals the blower housing
• Directs air from the lint screen through the exhaust duct
• Helps maintain proper airflow and drying performance
• Damage or gaps may cause reduced airflow, longer dry times, vibration/noise, or lint leaking inside the cabinet

• Unplug dryer and let components cool before servicing
• Access the blower housing; front or rear access varies by model
• Clean lint from housing and ducts; inspect the blower wheel and any gasket/seal
• Seat cover squarely and tighten fasteners evenly; verify the blower turns freely and no air leaks are present

This trim piece finishes and protects an opening or edge on your appliance's cabinet or console. Replacing a cracked or missing trim restores a clean, factory look and helps nearby components sit and operate as intended. What it does:

• Provides a clean, finished edge and covers sharp cabinet/console edges
• Helps keep adjacent parts aligned and secured around the opening
• Restores appearance when original trim is cracked, warped, discolored, or missing
• Common symptoms: loose or rattling piece, cosmetic damage, snagging edges, or poor fit of nearby parts

• 1 trim piece

• Disconnect power; if applicable, shut off gas or water. Wear cut-resistant gloves.
• Remove the existing trim by releasing clips or removing screws; note orientation and retain hardware.
• Transfer any reusable clips/inserts from the old trim to the new part.
• Align and snap/screw the new trim into place; do not overtighten.

This out exhaust pipe directs a dryer's exhaust airflow from the appliance to the home vent, helping remove moisture and lint from the dryer cabinet. Durable replacement for worn or damaged exhaust tubing. What it does:

• Channels hot, moist air from the dryer to the external vent to prevent moisture buildup
• Helps maintain proper airflow for efficient drying and reduces lint accumulation inside the cabinet
• Replaces cracked, crushed, or disconnected exhaust connections that cause poor venting or air leaks
• Works as a direct-fit plumbing piece when original exhaust piping is damaged

• One out exhaust pipe

• Disconnect power to the appliance before installing; for gas dryers, turn off gas supply and pilot per manufacturer instructions
• Ensure the pipe fits securely to the dryer outlet and the wall vent; use manufacturer-recommended clamps or fasteners
• Inspect and clean the vent path and lint screen while replacing the pipe to ensure safe airflow

This motor connector housing is the molded body that holds the motor's wire terminals for a secure, insulated connection. Replacing a cracked or heat-damaged housing helps restore reliable motor operation and prevent intermittent power issues.

• Organizes and insulates the motor's wiring terminals
• Locks the harness to the motor for a firm electrical connection
• Helps reduce loose contacts, arcing, and heat damage at the plug
• If the housing is failing, you may see intermittent or no motor operation, the machine stopping mid-cycle, or visible melting/discoloration at the motor connector

• Disconnect power; also shut off gas supply
• Note wire positions; transfer terminals into the new housing one at a time to maintain orientation
• Inspect terminals and wiring; replace any burnt or loose terminals before reassembly
• Ensure the connector seats fully on the motor and the harness is secure; restore power and test

Replacement end cap that restores the appliance's finished edge and helps protect internal components from debris. A simple, low-cost repair to replace cracked, broken, or missing end caps and reduce trim wear. What it does:

• Covers and protects an exposed edge or end of the cabinet/trim.
• Helps prevent snagging, dirt buildup, and contact damage where the cap is missing or cracked.
• Restores the appearance and alignment of surrounding trim pieces.
• Common symptom: visible crack, loose or missing trim, rubbing or catching at the edge.

• Disconnect power and/or water supply to the appliance before beginning work when applicable.
• Inspect the mating surface and remove old adhesive or fasteners before installing the replacement cap.
• Install by aligning the cap and snapping or fastening into place; do not force—use correct fasteners if applicable.
• If surrounding trim is damaged, consider replacing affected pieces to ensure proper fit and finish.

Color: Gray. Size: 13 oz. can. Used for coating the dryer drum interior. Acrylic appliance paint.

Replacement dryer drum that holds and tumbles laundry so air circulates evenly for efficient drying. Restores a smooth rotating drum surface to prevent fabric damage and improve drying performance. What it does:

• Houses and tumbles clothes while allowing heated air to pass through the load.
• Replaces a dented, cracked or scored drum that can catch or abrade fabric.
• Stops metal-on-metal scraping or grinding noises caused by a damaged drum surface.
• Helps eliminate uneven drying caused by a misshapen or warped drum.

• One replacement drum.

• Disconnect power (and gas supply for gas models) before starting any repair.
• Drum removal usually requires loosening the front panel and supporting the drum; consider a second person—the drum is heavy and awkward.
• Inspect and replace related components if worn to prevent repeat failures.
• Test-run the dryer after installation to ensure smooth rotation and proper clearance.

This 5-position fabric selector switch controls the dryer's fabric-cycle selection and associated heat/timing signals, restoring correct cycle choice and reliable control response when the original switch is faulty. What it does:

• Routes user fabric-setting selections to the dryer control so the correct cycle and heat options run.
• Common symptoms: selector won't move or click, dryer stays on one setting, or changing fabric settings has no effect.
• Helps eliminate intermittent or no-response issues from a worn or broken selector.
• Matches the control interface functions so cycles correspond to the chosen fabric type.

• Disconnect power before starting; for gas dryers also shut off the gas supply.
• Take photos of existing wiring and knob placement to ensure correct reassembly.
• Handle electrical connectors gently; verify secure connections and operation before final reassembly.

This exhaust cover plate protects and finishes the dryer's exhaust outlet, helping direct airflow and keeping the vent opening sealed from debris. It provides a clean, durable surface where the exhaust connects to the dryer cabinet. What it does:

• Covers and seals the dryer exhaust opening to prevent dust and lint buildup around the vent
• Helps direct exhaust airflow into the duct for proper ventilation
• Restores a finished appearance to the exhaust area after repair or replacement
• Can reduce drafts and discourage pests entering through the vent opening

• Disconnect power to the appliance before starting any work.
• Use basic hand tools; handle edges carefully to avoid cuts.
• Verify proper alignment with the exhaust opening and secure with the original screws or hardware.
• Inspect the exhaust duct and surrounding seals for wear.

This motor mounting bracket secures the appliance motor to the cabinet, keeping the motor steady for reliable operation and reduced vibration. It's a direct-fit replacement designed to restore proper motor alignment and support. What it does:

• Holds the motor in the correct position to prevent movement during operation
• Reduces motor vibration and noise caused by loose or damaged mounting
• Helps maintain proper belt alignment and drivetrain performance
• Supports safe, stable motor operation under normal load conditions

• One motor mounting bracket

• Disconnect power to the appliance before beginning any repair
• Basic mechanical skills and common hand tools are usually required
• Inspect mounting hardware and adjacent components; replace any worn fasteners

This harness clip secures appliance wiring to the cabinet or components to prevent rubbing, pinching, and interference with moving parts. It keeps wiring routed neatly for reliable operation and reduced risk of abrasion-related failures. What it does:

• Holds wire harnesses in place to prevent chafing against sharp edges or moving parts
• Reduces vibration-related noise and intermittent connections caused by loose wiring
• Helps maintain proper wire routing around panels, motors, and heaters
• Supports safe operation by keeping wires away from heat sources and pinch points

• Disconnect power to the appliance before servicing to avoid electric shock
• Remove panels or access covers as needed to reach the original clip location
• Install by snapping or seating the clip into the original mounting point and securing the harness in the retainer; replace any broken mounts
• Inspect surrounding wiring and replace damaged wires or insulation before completing repair

This is a replacement mounting screw used to secure panels and components on compatible Whirlpool appliances, restoring loose or missing fasteners for safe, stable operation. What it does

• Fastens appliance panels, brackets, and small components in place
• Replaces stripped, rusted, or missing screws that cause rattling or loose parts
• Helps restore proper alignment and reduce vibration-related noise
• Matches OEM fit and function for straightforward replacement

• One replacement screw

• Use the matching screwdriver or nut driver to avoid stripping the head
• Tighten until snug; do not overtighten to prevent thread or panel damage
• Turn off and unplug the appliance before accessing internal components