Kenmore Washer 110.6205307 (1106205307, 110 6205307) Parts
Genuine Whirlpool part
By: Whirlpool
Part Number: WP21258
The lid hinge bearing is used for the lid hinges on washers and dryers. When functioning properly, it allows the lid to open and close properly. If this is a problem with the bearing, it could make the lid difficult to move. In some cases, when the lid will not close, it means that the machine will not function correctly. Damaged lid hinge bearings should be replaced as soon as possible.The lid hinge bearings see a lot of work since they are in use whenever the lid of the washer or dryer opens and closes. They could become cracked and broken over time. Replacing the bearings is a relatively simple repair that owners can make on their own.This lid hinge bearing is for use with many models of washers and dryers from Whirlpool, KitchenAid, Roper, Estate, Inglis, Maytag, Admiral, Amana, Crosley, and Magic Chef. This is a genuine OEM replacement part that has been sourced from the manufacturer. The piece is sold individually, so if owners need to replace more than one hinge, they will need to buy multiples.
Do-It-Yourself Stories from Customers like You
Whirlpool washer David L. • Linn , MO • August 31, 2015
With the parts supplied from your company. The lady that took my order was good at her job. All the parts were correct and fit. I thank you for the service that recieved.
Read more
More
$5.95
- Compare At:
-
$7.08
- You Save:
-
$1.13
Genuine Whirlpool part
By: Whirlpool
Part Number: WP3400516
Secures panels or brackets in your laundry center to prevent vibration noise. Replace missing, stripped, or worn screws to restore a tight fit.
Do-It-Yourself Stories from Customers like You
No spin on spin cycle Richard S. • Beaumont , CA • August 28, 2015
Replaced clutch assembly which was a little tricky, but very doable. Just make sure to take your time. I do have to say that I am very impressed with AppliancePartsPro customer service when the replacement part also failed. A new clutch assembly was at my door step a few days later. I now has a working washer again. Thanks Again Appliance Parts Pro.
Read more
More
$7.56
- Compare At:
-
$8.32
- You Save:
-
$0.76
Genuine Whirlpool part
By: Whirlpool
Part Number: W11033823
Secures the door boot gasket to the front tub on front-load washers. Replace if the seal is loose or leaking during wash cycles. Confirm fit with model.
More
$8.95
- Compare At:
-
$10.74
- You Save:
-
$1.79
Genuine Whirlpool part
By: Whirlpool
Part Number: WP8546455
Supports the spin basket on the center post for smooth, quiet rotation. Replace if your washer is noisy, vibrating excessively, or has poor spin performance.
More
$18.26
- Compare At:
-
$21.91
- You Save:
-
$3.65
Genuine Whirlpool part
By: Whirlpool
Part Number: WP95405
Drive belt transfers motor power to spin the washer drum. Replace if you hear squealing, slipping, or complete spin failure. Verify fit with your model.
This part fixes the following symptoms
-
Burning smell
-
Will not drain
-
Pumps but will not spin
See more...
Do-It-Yourself Stories from Customers like You
Broken washer belt whirlpool imperial 70 Michael M. • Mesquite , TX • April 03, 2015
Very difficult fix even though I had done it once before about 15 years ago. Problem for me was getting the transmission down far enough to get clearance to install the belt. Model LA780P from the mid 80s. It started leaking transmission fluid and that worried and hurried me.
I bought a newer washer but went back to this older style because they are repairable. New ones are disposable and I like the old porcelin.
The only two parts that ever break are the belt and the pump, the pump being...
Read more
More
$25.95
- Compare At:
-
$31.14
- You Save:
-
$5.19
Genuine Whirlpool part
By: Whirlpool
Part Number: W11693756
Type AB #8-18 x 5/8 inch thread-forming screw secures panels and components in appliances. Replace missing, stripped, or corroded fasteners.
Do-It-Yourself Stories from Customers like You
Door switch on dryer. James A. • Middleburg , FL • January 20, 2020
It was very easy to fix after watching your video..
Read more
More
$12.54
- Compare At:
-
$12.92
- You Save:
-
$0.38
Genuine Whirlpool part
By: Whirlpool
Part Number: WP21097
Cushioning pad that installs between the washer lid hinge and cabinet. Replace if cracked, worn, or missing to reduce squeaks and prevent metal wear.
Do-It-Yourself Stories from Customers like You
Cracked lid on a whirlpool cabrio washer Doug P. • Kansas City , MO • September 05, 2015
Removed the screws, lifted the old lid out of the hinges. Replaced the hinges, set new lid in the hinges and replaced screws.
Read more
More
$5.95
- Compare At:
-
$7.08
- You Save:
-
$1.13
Genuine Whirlpool part
By: Whirlpool
Part Number: WP16123
Rubber washer gasket for washer fill hose connections. Replace if worn or leaking at coupler adapter. Measures 1-1/16 x 5/8 inch. Verify fit with model.
Do-It-Yourself Stories from Customers like You
Water inlet valve was corroded and broken washer Sandra H. • Belton , MO • June 26, 2015
Replaced with new part ordered from store
Read more
More
$5.95
- Compare At:
-
$7.02
- You Save:
-
$1.07
Genuine Whirlpool part
By: Whirlpool
Part Number: WP91770
Right hand side
Do-It-Yourself Stories from Customers like You
Lid was rusted bad Mike S. • San Lorenzo , CA • December 06, 2016
New parts easy fix
Read more
More
$17.95
- Compare At:
-
$21.18
- You Save:
-
$3.23
Genuine Whirlpool part
By: Whirlpool
Part Number: WP21365
Small metal spacer washer that distributes load and maintains alignment in washer assemblies. Replace when worn, missing, or damaged to restore secure fit.
Do-It-Yourself Stories from Customers like You
Washing machine would not agitate or spin. Laurie W. • Webster , NH • March 25, 2017
We were a bit doubtful that we could find parts for this Whirlpool washing machine as it is 22 years old. We were SO pleased that not only could we find them ( with excellent customer service) but they were shipped in an appropriate time. My handy husband was then able to repair it himself :)
Read more
More
$7.40
- Compare At:
-
$8.81
- You Save:
-
$1.41
Genuine Whirlpool part
By: Whirlpool
Part Number: WP62837
Knurled pin secures knobs or dials to control shafts in washers. Replace if the original is missing, worn, or damaged to stop loose or spinning knobs.
Do-It-Yourself Stories from Customers like You
Whirlpool shaking Willy P. • Victorville , CA • May 19, 2019
Weekend laundry became very noisy, our 1987 Whirlpool washer began doing a dance across the floor and the drum was banging into the inner cabinet. After doing some research and watching a few videos on Appliance parts pros website. I inspected the washer and noticed one leg the rubber coating disintegrated, decided to change all four legs, springs and lid switch. Hardest part of the job is getting the cabinet together. Ops check good.
Read more
More
$7.47
- Compare At:
-
$8.96
- You Save:
-
$1.49
Genuine Whirlpool part
By: Whirlpool
Part Number: WP3351614
Size: 10-24 x 3/8 inch.
Do-It-Yourself Stories from Customers like You
Timer/control failed Gilbert G. • Lansing , IL • July 09, 2018
Replaced timer control unit, first time doing this.
Read more
More
$7.56
- Compare At:
-
$8.32
- You Save:
-
$0.76
Genuine Whirlpool part
By: Whirlpool
Part Number: WP358160
This lock nut secures appliance components and resists loosening from vibration. Replacing a stripped, rusted, or missing nut restores a firm, reliable connection to reduce noise and prevent parts from shifting or backing off.
- Secures brackets, shafts, pulleys, panels, or other hardware as designed by the manufacturer
- Helps prevent fasteners from loosening due to vibration and thermal cycling
- Common fix for rattling/vibration noises and components that work loose over time
- Replaces damaged, rounded, or missing original nut to restore proper fit
What's included: 1 lock nut Install notes:
- Disconnect power and shut off gas/water supplies before servicing
- Remove the worn nut with the appropriate wrench or socket
- Start the new nut by hand to avoid cross-threading; tighten securely—do not overtighten
- Inspect the mating bolt/stud and any washers; replace if worn or damaged
Do-It-Yourself Stories from Customers like You
Dryer drum was making one heck of a racket while running Michael R. • Closter , NJ • January 08, 2015
The cylinder roller that supports the dryer drum was worn and needed to be replaced. I ordered the idler pulley shaft and associated parts as well since I wasn't sure if these were worn too.
Watching the video on the web site gave me a good idea what was involved and where to look. It wasn't my exact model and make but provided sufficient information on what to look for. The parts were exact fits which was a great relief abd the dryer is running like new again!
Read more
More
$2.09
- Compare At:
-
$4.46
- You Save:
-
$2.37
Genuine Whirlpool part
By: Whirlpool
Part Number: 3184020
This ground wire provides a safe chassis connection to restore proper grounding and reduce shock and electrical-fault risk. It replaces a frayed, corroded or missing ground lead to help keep the appliance electrically safe. What it does
- Connects the appliance chassis to the grounding system to prevent stray voltage on metal surfaces
- Restores a secure ground path if the original wire is broken, loose, or corroded
- Helps stop intermittent power faults or nuisance tripping caused by a compromised ground
- Addresses symptoms like visible wire damage, loose ground connection points, or grounding-related electrical issues
What's included
Install notes
- Always disconnect power (unplug or shut off the circuit breaker) before starting work
- Attach the ring/terminal ends to the designated chassis ground screw and the equipment ground point
- Route the wire away from moving parts, heating elements, and sharp edges; secure with existing clips or fasteners
- If terminal hardware is missing or damaged, replace with equivalent OEM-style fasteners and torque to specification
More
$50.57
- Compare At:
-
$59.67
- You Save:
-
$9.10
Genuine Whirlpool part
By: Whirlpool
Part Number: 350920
This bearing supports the spin basket (inner tub) in top-load washers, allowing it to rotate smoothly during the spin cycle. It is mounted at the base of the spin basket and bears the load of the drum and its contents. Replace this bearing if the washer makes loud grinding or squealing noises during the spin cycle, if the basket wobbles excessively, or if you notice water leaking from beneath the tub.
More
$4.95
- Compare At:
-
$5.94
- You Save:
-
$0.99
Genuine Whirlpool part
By: Whirlpool
Part Number: WP95440
This connector hose links appliance plumbing components to restore a sealed water path and proper flow. It replaces a damaged or leaking hose section so the appliance can refill and drain as intended. What it does:
- Re-establishes a sealed hose connection between intake/drain plumbing points
- Prevents leaks caused by cracked, split, or worn hose fittings
- Helps restore normal water fill or drain behavior when the original connector fails
- Compatible with the factory connection points shown in the OEM parts diagram
What's included: One connector hose as pictured. Install notes:
- Turn off power and shut off the water supply before starting work
- Inspect adjacent clamps and fittings; replace any damaged hardware for a secure seal
- Use proper hose clamps and ensure connections are tight but not over-torqued
Do-It-Yourself Stories from Customers like You
Leaking washer. Nicholas R. • Lewistown , MT • January 09, 2023
Replaced the connector to the hose that sends water to the drain.
Read more
More
$8.95
- Compare At:
-
$10.56
- You Save:
-
$1.61