Kenmore Washer 110.7304622 (1107304622, 110 7304622) Parts
Genuine Whirlpool part
By: Whirlpool
Part Number: WP21258
The lid hinge bearing is used for the lid hinges on washers and dryers. When functioning properly, it allows the lid to open and close properly. If this is a problem with the bearing, it could make the lid difficult to move. In some cases, when the lid will not close, it means that the machine will not function correctly. Damaged lid hinge bearings should be replaced as soon as possible.The lid hinge bearings see a lot of work since they are in use whenever the lid of the washer or dryer opens and closes. They could become cracked and broken over time. Replacing the bearings is a relatively simple repair that owners can make on their own.This lid hinge bearing is for use with many models of washers and dryers from Whirlpool, KitchenAid, Roper, Estate, Inglis, Maytag, Admiral, Amana, Crosley, and Magic Chef. This is a genuine OEM replacement part that has been sourced from the manufacturer. The piece is sold individually, so if owners need to replace more than one hinge, they will need to buy multiples.
Do-It-Yourself Stories from Customers like You
Whirlpool washer David L. • Linn , MO • August 31, 2015
With the parts supplied from your company. The lady that took my order was good at her job. All the parts were correct and fit. I thank you for the service that recieved.
Read more
More
$11.95
- Compare At:
-
$13.33
- You Save:
-
$1.38
Genuine Whirlpool part
By: Whirlpool
Part Number: WPW10109200
This replacement screw secures panels, brackets, and other components in your appliance to keep them aligned and rattle-free. Replacing worn, stripped, or missing hardware restores a tight fit and helps maintain safe, quiet operation.
- Fastens panels, brackets, or internal parts to the cabinet/frame
- Helps maintain alignment to reduce vibration and rattling
- Replaces lost, stripped, or corroded screws
- Common symptoms: loose panels/trim, rattles, or a screw that won't tighten
What's included: One screw. Install notes:
- Disconnect power; shut off water or gas if applicable
- Match thread and length to the original; replace one at a time to keep alignment
- Start threads by hand to avoid cross-threading; use the correct driver
- Tighten snugly—do not overtighten, especially into plastic or thin sheet metal
Do-It-Yourself Stories from Customers like You
Missing baffles Anna S. • Shoreview , MN • January 31, 2016
I ordered two replacement baffles and screws, then lifted the top of the dryer to access the drum and installed the two new baffles.
Read more
More
$5.95
- Compare At:
-
$7.14
- You Save:
-
$1.19
Genuine Whirlpool part
By: Whirlpool
Part Number: WP3400516
Secures panels or brackets in your laundry center to prevent vibration noise. Replace missing, stripped, or worn screws to restore a tight fit.
Do-It-Yourself Stories from Customers like You
Gearbox replacement Dennis M. • Comer , GA • October 21, 2018
Followed online video. It was easy
Read more
More
$5.95
- Compare At:
-
$7.02
- You Save:
-
$1.07
Genuine Whirlpool part
By: Whirlpool
Part Number: WP616099
This hose clamp secures a hose connection to prevent leaks and keep your appliance running smoothly. It provides a tight, reliable hold on the hose fitting so water or air stays contained during operation.
- Tightens around a hose and fitting to maintain a secure seal
- Helps stop drips, seepage, or loose connections
- Common fix when you see moisture around a hose joint
- Useful if a clamp is rusted, stretched, or no longer holding tension
What's included: One hose clamp. Install notes:
- Unplug power and shut off water (if applicable) before servicing
- Note clamp position/orientation before removal
- Use appropriate screwdriver or nut driver to tighten evenly
- Do not overtighten—ensure a snug, leak-free seal without damaging the hose
Do-It-Yourself Stories from Customers like You
Water leak Steven K. • New City , NY • August 10, 2018
Took off cover, installed new parts.
Read more
More
$9.95
- Compare At:
-
$11.59
- You Save:
-
$1.64
Genuine Whirlpool part
By: Whirlpool
Part Number: WP8546455
Supports the spin basket on the center post for smooth, quiet rotation. Replace if your washer is noisy, vibrating excessively, or has poor spin performance.
More
$18.26
- Compare At:
-
$21.55
- You Save:
-
$3.29
Genuine Whirlpool part
By: Whirlpool
Part Number: W11033823
Secures the door boot gasket to the front tub on front-load washers. Replace if the seal is loose or leaking during wash cycles. Confirm fit with model.
More
$8.95
- Compare At:
-
$10.65
- You Save:
-
$1.70
Genuine Whirlpool part
By: Whirlpool
Part Number: WP95405
Drive belt transfers motor power to spin the washer drum. Replace if you hear squealing, slipping, or complete spin failure. Verify fit with your model.
This part fixes the following symptoms
-
Burning smell
-
Will not drain
-
Pumps but will not spin
See more...
Do-It-Yourself Stories from Customers like You
Broken washer belt whirlpool imperial 70 Michael M. • Mesquite , TX • April 03, 2015
Very difficult fix even though I had done it once before about 15 years ago. Problem for me was getting the transmission down far enough to get clearance to install the belt. Model LA780P from the mid 80s. It started leaking transmission fluid and that worried and hurried me.
I bought a newer washer but went back to this older style because they are repairable. New ones are disposable and I like the old porcelin.
The only two parts that ever break are the belt and the pump, the pump being...
Read more
More
$21.56
- Compare At:
-
$28.39
- You Save:
-
$6.83
Genuine Whirlpool part
By: Whirlpool
Part Number: WP21097
Cushioning pad that installs between the washer lid hinge and cabinet. Replace if cracked, worn, or missing to reduce squeaks and prevent metal wear.
Do-It-Yourself Stories from Customers like You
Cracked lid on a whirlpool cabrio washer Doug P. • Kansas City , MO • September 05, 2015
Removed the screws, lifted the old lid out of the hinges. Replaced the hinges, set new lid in the hinges and replaced screws.
Read more
More
$9.63
- Compare At:
-
$11.46
- You Save:
-
$1.83
Genuine Whirlpool part
By: Whirlpool
Part Number: WP16123
Rubber washer gasket for washer fill hose connections. Replace if worn or leaking at coupler adapter. Measures 1-1/16 x 5/8 inch. Verify fit with model.
Do-It-Yourself Stories from Customers like You
Water inlet valve was corroded and broken washer Sandra H. • Belton , MO • June 26, 2015
Replaced with new part ordered from store
Read more
More
$5.95
- Compare At:
-
$7.08
- You Save:
-
$1.13
Genuine Whirlpool part
By: Whirlpool
Part Number: WP273556
Size: 10-16 x 5/8 inch.
Do-It-Yourself Stories from Customers like You
Console screws were rusty and the other screw was broken. Denis C. • Baltimore , MD • June 20, 2018
I used a screwdriver and removed all three screws and replaced them with ones I ordered from you. The job took less than ten minutes to complete.
Read more
More
$5.95
- Compare At:
-
$7.14
- You Save:
-
$1.19
Genuine Whirlpool part
By: Whirlpool
Part Number: WP90016
Used from harness to top.
Do-It-Yourself Stories from Customers like You
A broken lid switch on my whirlpool stackable twin washer Joseph P. • Indialantic , FL • October 25, 2016
Fixing the problem was quite simple. First, I removed the lid assembly (thanks to the diagrams supplied by AppliancePartsPros.com!). Getting the back two screws out was very difficult because I couldn't see them from the front and I could not move the unit out of the enclosed space. After some trial and error, I located the screws which were 5/16 hex head screws and removed them with a MAGNETIC nut driver. (The magnet assures that the screw will not drop down into the mechanism). Second, I...
Read more
More
$7.44
- Compare At:
-
$8.85
- You Save:
-
$1.41
Genuine Whirlpool part
By: Whirlpool
Part Number: WP354255
A small rubber bumper that cushions and protects appliance doors, drawers or panels to reduce noise and prevent hard contact. Replaces worn or missing bumpers to restore a snug, quiet close. What it does:
- Provides a soft buffer to stop doors or drawers from banging into the cabinet or frame
- Reduces vibration and rattling during operation
- Helps doors and panels sit properly when closed
- Simple, non-electrical part — no wiring or adjustment required
What's included:
Install notes:
- Inspect the mounting hole or surface; clean debris before installing
- Press the bumper into the hole or onto the surface until fully seated; use a blunt tool if needed for tight fits
- Disconnect power to the appliance first and follow OEM instructions
- Remove old adhesive before installing the new bumper
Do-It-Yourself Stories from Customers like You
Needed water pump and lid switch Joe N. • Palmdale , CA • November 16, 2019
I utilized your videos. The pump video implied if the leak was ignored? You would have to cut the pump off, which was what I did. The impeller also had to be cut down to the plastic collar on the motor shaft, which I used a handheld chop grinder to get through the plastic collar without damaging the shaft, because of the neglect on the leak the motor shaft had to be filed and sandpapered to accept the new pump. The harness clips on the lid switch were difficult to get to but I managed without...
Read more
More
$5.95
- Compare At:
-
$7.08
- You Save:
-
$1.13
Genuine Whirlpool part
By: Whirlpool
Part Number: WP91770
Right hand side
Do-It-Yourself Stories from Customers like You
Lid was rusted bad Mike S. • San Lorenzo , CA • December 06, 2016
New parts easy fix
Read more
More
$20.27
- Compare At:
-
$21.36
- You Save:
-
$1.09
Genuine Whirlpool part
By: Whirlpool
Part Number: 350365
Fix a washer that won't drain or spin with this drain pump. Common repair for water remaining in tub after cycle. Moderate DIY repair effort.
Do-It-Yourself Stories from Customers like You
Water drain pump would not turn any more Robert T. • Belleville , IL • January 20, 2016
Ordered a replacement. Had to tip washer toward the back to provide access underneath to the
pump. Had some difficulty removing the two hose clamps. Pliers were not the best tool. Had to ensure the drive belt was properly engaged with the pulley of the pump.
Read more
More
$96.59
- Compare At:
-
$115.91
- You Save:
-
$19.32
Genuine Whirlpool part
By: Whirlpool
Part Number: WP359231
Washer won't start or stops mid-cycle? A damaged lid switch shield can expose wiring to moisture, causing safety interlock failures. Simple fix.
More
Genuine Whirlpool part
By: Whirlpool
Part Number: 358277
Washer won't fill, overfills, or leaks? A faulty water inlet valve is often the cause. DIYers report 10-20 minute fixes for this common washer repair.
This part fixes the following symptoms
-
No hot or cold water
-
Will not fill with water
-
Will not stop filling with water
See more...
Do-It-Yourself Stories from Customers like You
Washing machine took 30 minutes to fill because the inlet valve was failing Chris G. • Dunedin , FL • June 13, 2016
I ordered the replacement inlet valve from your site, installed it in 20 minutes. the washing machine now fills to extra large capacity in 3 minutes. The machine is an old Kenmore bought new in 1985, this inlet valve is the only component to fail in the over 30 years we have had it.
Read more
More
$93.72
- Compare At:
-
$111.53
- You Save:
-
$17.81