Kenmore Dryer 110.87566602 (11087566602, 110 87566602) Parts

Size: 6 - 20 x 1 1/16 inch.

Small replacement clip that secures panels or small internal components to restore a snug fit and reduce rattling or misalignment. Use this clip when a worn or broken retainer lets trim or parts sit loose. What it does:

• Holds trim, panels or other small appliance components in place to maintain correct alignment.
• Helps eliminate rattling, vibration noise or gaps caused by a missing or damaged clip.
• Restores secure fit where a broken clip allows parts to shift or separate.
• Simple, low-profile replacement part used in affected Whirlpool appliances.

• Disconnect power (unplug or shut off breaker) before servicing any appliance.
• Small part; keep track of screws and retainers during disassembly.
• Basic hand tools may be required; trim or panel removal might be necessary to access the clip.

Dryer Vent Test Kit ensures your dryer's vent system is operating properly. Kit includes two tests depending on the location of your dryer's lint screen: One for the lint screen in the top of your dryer, and one for the lint screen in the front of your dryer. Instructions included.

This door seal is the refrigerator door gasket that helps maintain a tight seal to keep cold air in and reduce energy loss. Replacing a worn or torn gasket helps the appliance cool efficiently and protect stored food. What it does

• Forms an airtight barrier around the refrigerator door to prevent warm air from entering
• Helps maintain consistent internal temperature and efficient operation
• Reduces frost buildup and cycling caused by a leaking seal
• Commonly shows symptoms like visible cracks, tears, flattening, or a door that won't close snugly

• One refrigerator door gasket

• Inspect the door frame and strike surfaces; clean mounting channel before installing the new gasket
• Warm the gasket slightly or use recommended installation tools to ease fitting into the channel
• Check alignment and closure after installation; replace if mounting clips or retainer are damaged
• Disconnect power only if required by your model and follow all safety precautions

This multi-vent plug seals an unused vent opening to stop unwanted airflow and keep the appliance interior protected. It's a direct-fit replacement designed to restore proper venting and help prevent drafts, debris, and pests. What it does:

• Plugs an unused multi-vent opening to prevent air leakage and drafts
• Helps keep dust, lint, and small debris out of the appliance vent path
• Reduces the chance of pest entry through an open vent
• Restores the intended vent configuration after service or part removal

• Disconnect power or gas to the appliance before servicing for safety
• Install by aligning and pressing the plug firmly into the vent opening until seated
• Do not force if resistance is excessive; inspect for obstructions or damage
• Replace damaged parts before installing the plug

Color: White

This control knob replaces a worn or broken range/oven front knob to restore tactile control and clear temperature/setting selection. It gives a secure fit so you can safely set burners or oven functions. What it does:

• Replaces a damaged or missing control knob to restore manual control of burners or oven settings
• Provides a clear pointer for accurate selection of heat levels and functions
• Snaps on to the stove/range control shaft for reliable operation
• Helps eliminate slipping, stripped splines, or loose turning caused by a worn knob

• One control knob as shown

• Turn power and gas supply off before servicing; follow appliance safety guidance
• Pull off the old knob straight from the control shaft and push the replacement fully onto the shaft until it seats
• If knob does not fit, do not hammer or modify the shaft

This housing slot heater melts ice and prevents frost buildup inside the appliance housing, helping restore normal airflow and component operation. It's a direct replacement heater element used where ice forms around the housing slot. What it does:

• Provides targeted heat to the housing slot to reduce ice accumulation
• Helps restore proper airflow and circulation by clearing frost/ice blockages
• Commonly replaced when the housing develops repeated ice buildup or intermittent heating
• Works as part of the defrost/anti-ice system to protect internal components

• Disconnect power to the appliance before servicing to avoid electrical shock
• Access typically requires removing exterior panels or trim; keep fasteners organized
• Handle the heater element and wiring with care to avoid damage to the element or connector

This replacement dryer drum restores the rotating drum that holds and tumbles clothes during drying, helping ensure proper airflow and even drying. It's a direct-fit exterior rotating drum used in compatible Whirlpool-family dryers. What it does:

• Replaces a cracked, dented or warped drum that can catch or damage clothing
• Restores smooth tumbling to reduce noise and fabric snags
• Maintains proper airflow path for efficient drying performance
• Works with existing rollers, bearings and seals when those components are serviceable

• High-level task: remove cabinet and front bulkhead to access and swap the drum; follow your model-specific service manual
• Disconnect power (and gas supply for gas dryers) before starting any repair
• Inspect and replace worn rollers, glides, seals or bearings as needed—this drum typically does not include those components

Outer door glass that restores the oven door viewing window and replaces cracked, chipped, or broken glass so the door functions safely and looks like new. What it does

• Replaces damaged or shattered outer door glass to restore a clear viewing window.
• Stops rattling or loose glass caused by broken mounting points or cracks.
• Helps maintain proper door appearance and user visibility into the oven cavity.
• Useful when glass has visible chips, cracks, or safety concerns.

• One outer door glass

• Disconnect power to the appliance before beginning any repair.
• Handle glass with heavy-duty gloves and eye protection; glass can break unexpectedly.
• Replacing this part typically requires removing the oven door and disassembling panels—follow the OEM service manual or instructions.
• Inspect and replace any worn clips, screws, or seals as needed; do not overtighten fasteners.