Kenmore Refrigerator 253.51693105 (25351693105, 253 51693105) Parts

If you can't pull out the displacement pins on the crisper cover support clips that allow the wall to carry the weight of the cover, slides and drawer, you may need to push those pins in (they fall down the wall) to remove the clip. During the replacement of both front clips, I had one I could remove and one I had attempted to drill a tiny hole in to be able to pull the pin. Ultimately it did not work and needed to be simply pushed in. Do not worry, there is nothing below which the plastic... Read more

Before we replaced the board, my wife tried to replace just the element. We had one we had ordered several years ago when this same thing happened. When that didn't work we replaced the board and could see where the old board was damaged so we figured this was the solution. It would have been except the bottom element my wife used to replace the old element (which was fine but had been thrown out figuring the new one was new so why keep the old one) was 1" shorter in the back than the old... Read more

Manufacturer no longer makes part, but found rough equivalent by searching AppliancePartsPros.com web site. Not exact fit, but excellent substitution. Simple replacement of shelf on existing bracket. Read more

• Noisy

1. After hearing a loud noise on the freezer side of unit about halfway up, I started investigating what it could be? My conclusion was evaporator motor or evaporator fan blade. One of the signs of this issue was a distinct change in sound when I opened the freezer door. I ordered a new motor and blade, not knowing exactly what it was. 2. I couldn't get water to dispense, so I changed the filter and that wasn't the problem. I ordered a water valve and crossed my fingers. These parts arrived... Read more

I wasn't sure if it was the door being warped, the spring return being worn, or the rotary damper failing, so I ordered all to update the door mechanism. I also ordered a new micro switch since one of the switches had started to require more and more pressure to actuate. Figured I'd fix it at the same time. Repair was very straightforward and the videos available on this and other repair sites were very helpful. I found a video that showed replacing the door mechanism on a nearly identical... Read more

Replaced the cold control. I have no experience working on appliances but went well. It took about 2 hours of work but I went slow and took pictures in case I needed to reference later. Saved $200 in labor by doing it myself. Read more

I wasn't sure if it was the door being warped, the spring return being worn, or the rotary damper failing, so I ordered all to update the door mechanism. I also ordered a new micro switch since one of the switches had started to require more and more pressure to actuate. Figured I'd fix it at the same time. Repair was very straightforward and the videos available on this and other repair sites were very helpful. I found a video that showed replacing the door mechanism on a nearly identical... Read more

Ordered left and right side supports and they arrived in two days! It took me longer to get stuff out of the way in the fridge so I could take the shelf out than it did to actually swap out the side supports. Parts fit perfectly and quick easy repair. Read more

Initially I noticed the crusher drum was cracked and broken so I replaced the drum the retaining nut on the end of the auger and the circlip and washer. it worked fine for a time and then the drum began free wheeling. upon further inspection I discovered the retain nubs on the auger had worn down allowing the blade to slip down the auger body. so I replaced the auger, drum, drive blade, and drive cam. I recommend if you gave a problem with the ice dispenser you break down and inspect the entire... Read more

• Door won't open or close
• Door sweating
• Clicking sound

I went to Appliance Parts Pros and watched a few videos. Ordered the door closer plate and door hinge bearing. Removed all of the door bins and contents. Removed four screws total. Lifted the door off of the hinge, replace the two parts on the bottom hinge. Put the door back on the hinge with a little silicone on the new parts. Replaced all of the screws and no more popping. It took more time to clean all of the door bins than to fix the hinge. The video was 100% accurate. No surprises. Read more

• Ice maker won't dispense ice
• Ice maker not making ice
• Leaking

After about three months of returning to my youth, filling ice cube trays, I decided to venture into the freezer and yank the old ice maker from its mounting. Since this was the third time this very ice maker had decided to stop functioning, it was time to get a replacement. I suspected the heating element was open and the motor was screaming trying to push the little frozen blocks of ice from their form, with distortion occurring. I ordered a replacement from this very company, received it... Read more

• Door sweating
• Door won't open or close

Replaced the lower hinge bearing and lower door cam on fridge side. Read more

• Ice maker dispenses too much ice

Replaced the housing Read more

Thanking APP ahead of time for expedient 1 day express parts & videos! I kept a LOG on this repair fix starting 6/21/20: started with cleaning out behind the Frigidaire /coils, fan blade, floor, walls, toe-plate, compressor. #1 Replaced just the Run Capacitor [from my local appl store]. Somewhat better but not a fix. Fridge controls need much higher settings than Factory Settings - which is recommended. Did some homework on several sites /kept coming back to yours / saw what parts are probably... Read more

Ordered part from appliancepartspros.com and got them within 2 days.that was great,refrigerator is like new again,am I am pleased with service and there swift delivery. If I need any thing else,there is only one place I will get them.from. Thanks! Read more

Used same tools as in your video. Read more