Kenmore Washer Dryer Combo 417.97862791 (41797862791, 417 97862791) Parts

This genuine replacement spring restores proper tension and smooth movement in the affected mechanism, helping your appliance operate reliably. Replacing a weakened or broken spring can reduce noise and correct misalignment caused by lost tension.

• Maintains tension and provides return force for connected levers, brackets, or linkages
• Helps keep components in position and minimizes excess play or rattling
• A weakened, stretched, or broken spring can cause poor engagement or inconsistent operation
• Common signs include parts not returning to rest, excess slack, or new noises from the area

• Disconnect power; also shut off water supply
• Note the spring's hook orientation and routing; take a reference photo before removal
• Control the spring with pliers and wear gloves/eye protection to avoid snap-back injuries
• Inspect related brackets/retainers and replace any worn components to ensure proper tension

This replacement bolt secures internal components in your appliance. A stripped, rusted, or missing bolt can let parts loosen and vibrate; installing a new bolt restores a tight, stable connection for reliable operation.

• Provides a secure, threaded fastener for brackets, weights, or assemblies
• Helps maintain alignment and reduce movement during operation
• Typical issues: missing hardware, stripped threads, or visible corrosion
• Helps address rattling or excessive vibration caused by loose hardware

• Safety first: Disconnect power; for water- or gas-connected units, shut off supplies
• Support the component being secured before removing the old fastener
• Start threads by hand to avoid cross-threading; tighten evenly to manufacturer guidance—do not overtighten
• Reuse original washers/spacers and thread locker only if they were originally present

This burner orifice meters gas to a range/cooktop burner through a calibrated opening. Replacing a clogged, damaged, or incorrect-size orifice helps restore proper flame height and clean, consistent combustion for reliable cooking performance.

• Regulates fuel flow to the burner via the precisely sized orifice opening
• Helps address weak/uneven flame, yellow or sooty flame, or delayed ignition
• Replaces stripped, blocked, or wrong-size orifice spud
• Size- and position-specific—match the stamped size and location

• Disconnect electrical power and shut off the gas supply before servicing
• Allow the cooktop to cool; remove grates, caps, and burner head to access the orifice holder
• Use the proper orifice/nut driver; do not overtighten or alter/enlarge the opening
• After reassembly, restore gas and leak-test with an approved solution; verify a stable blue flame and adjust air shutters if applicable

Keep your dryer tumbling smoothly by restoring proper belt tension. This idler spring attaches to the idler arm and maintains tension on the drive belt so the drum turns reliably without slipping or squealing. What it does:

• Applies constant tension to the idler pulley to keep the drive belt tight around the drum and motor
• Helps resolve a drum that won't turn or tumbles intermittently
• Addresses belt issues such as slipping off, appearing loose, or premature breakage from low tension
• Can reduce squealing/chirping from the idler area caused by belt slip

• 1 idler spring

• Disconnect power; for gas dryers, also shut off the gas supply
• Access the idler assembly by removing the front or lower access panel per your model
• Relieve belt tension, unhook the old spring from the idler arm/frame, and install the new spring in the same orientation and holes
• Rotate the drum by hand to check smooth operation before reassembly

Restore visibility inside your appliance. This lamp assembly replaces a damaged or failed interior light so you can clearly see contents when the door opens, helping maintain safe, reliable illumination in the cabinet/drum.

• Provides interior illumination when the door opens or when the control calls for light
• Houses the bulb and makes the electrical connection
• Common symptoms: no interior light, flickering/intermittent light, or heat-damaged/burned socket or housing

• Disconnect power before servicing to avoid electrical shock
• Access the lamp from the interior or service panel per model
• Install a bulb with the correct type and wattage specified for your model
• Test light operation before reassembling panels

Agitator screw spacer positions and cushions the agitator screw on top-load washers to keep the agitator stable and reduce wear. It helps maintain correct agitator alignment for reliable wash performance. What it does:

• Centers the agitator and creates the correct spacing for the agitator screw
• Prevents metal-on-metal contact that can cause noise, wear, or loosening
• Helps stop the agitator from wobbling or shifting during the spin cycle
• Contributes to secure engagement between the agitator and the transmission

• Disconnect power to the washer before beginning service
• Remove the agitator per the manufacturer's service instructions to access the screw and spacer
• Install the spacer flat and seated, then reinstall the screw and agitator; follow the OEM service manual for proper fastening procedure
• Inspect the agitator and screw for wear or damage and replace as needed

This spring restores tension to the door lock mechanism so the latch returns to its proper position after operation. A worn or missing spring can cause a loose latch, difficulty locking, or a door that won't stay secured during a cycle.

• Returns the door lock latch to its resting position
• Helps ensure the door locks securely during operation
• Symptoms can include a floppy/loose latch, intermittent lock errors, or door not staying latched
• Also helps resolve issues where the door won't unlock smoothly

• Disconnect power before servicing
• Access the door lock assembly per your model's service procedure
• Note spring orientation during removal; install the new spring in the same positions
• Latch operation by gently opening/closing the door before reassembling

A replacement mounting screw used to fasten panels and components in compatible Frigidaire appliances. Replacing a missing or damaged screw restores secure fastening, reduces vibration/rattling, and helps keep parts aligned for reliable operation. What it does:

• Secures panels, trim, brackets or small components to prevent movement and rattling
• Replaces missing, stripped, or damaged fasteners that can cause loose or misaligned parts
• Helps maintain proper fit and finish of appliance panels and access covers
• Useful when a loose screw causes vibration noise or minor part movement

• Unplug the appliance or shut off power at the breaker before servicing electrical appliances
• Use the correct screwdriver or bit to match the screw head to avoid stripping
• Start threads by hand, then tighten until snug; avoid overtightening which can strip threads or crack plastic
• Keep small parts away from children and retain any removed hardware for reuse

This lid strike mounts to the washer lid and engages the lid lock/switch when the lid is closed. It signals the control that the lid is shut so the cycle can start and spin safely without interruption.

• Engages the lid lock/switch to confirm the lid-closed status
• Allows cycles to start and spin once the lid is shut
• Typical failure symptoms: washer won't start or spin; lid won't lock; strike is broken or missing
• Restores reliable lid engagement and safety interlock operation

• Unplug the washer before servicing
• Open the lid and remove the damaged strike from the lid (retain any screws if present)
• Align and secure the new strike; ensure it lines up with the lid lock opening
• Close the lid to verify smooth engagement before restoring power

This LP conversion kit supplies the manufacturer-specified components to configure a compatible gas appliance for propane use. It helps restore proper flame characteristics and safe, efficient performance after switching from natural gas service. What it does:

• Provides the correct orifice sizing and regulator setup for LP operation
• Helps address yellow/sooty flames, weak heat, or delayed ignition after a fuel-type change
• Supports stable burner ignition and proper combustion
• Intended only for models the manufacturer designates as convertible

• One LP conversion kit

• Turn off gas and electrical power; allow the appliance to cool before starting
• Follow the model-specific instructions included with the kit to change orifices and set the regulator/cap
• After installation, leak-test all gas connections and verify flame appearance per the service/installation sheet

A replacement bracket screw used to fasten internal brackets and panels to the appliance frame, restoring secure mounting and reducing rattling or misalignment caused by stripped, corroded, or missing fasteners. What it does

• Secures mounting brackets, panels or trim to the appliance chassis.
• Restores proper alignment and prevents movement or vibration-related noise.
• Use when the original screw is stripped, rusted, broken, or missing.
• Square-drive head provides a reliable engagement for positive tightening.

• Disconnect power to the appliance before servicing to avoid electrical hazard.
• Use the correct square (Robertson) driver to avoid cam-out and head damage.
• Tighten until snug; avoid over-tightening which can strip threads or crack panels.
• If threads are damaged, replace with the matching screw size and type or repair threads before reuse.

The blower housing assembly encloses the blower wheel and channels air through the unit's coils. Replacing a cracked or warped housing helps restore smooth airflow and reduce blower noise caused by rubbing or misalignment.

• Directs and focuses airflow through the heat-exchange coils for proper operation
• Supports and aligns the blower wheel so it spins with correct clearance
• Helps minimize vibration and noise when the housing is intact
• Symptoms of a failed housing may include scraping or rattling noises, weak airflow, vibration, or visible cracks/broken mounts around the blower area

• Disconnect power before servicing; wear cut-resistant gloves and eye protection.
• Remove the front panel/cabinet to access the blower section; note screw and clip locations.
• Transfer the blower wheel, seals, and any reusable hardware from the old housing.
• Before reassembly, spin the blower wheel by hand to ensure free, rub-free rotation.

This heater baffle mounts near the heating element to deflect and distribute radiant heat. It helps protect nearby surfaces and wiring while promoting more even temperatures and reliable performance inside the appliance.

• Directs and diffuses heat from the element to reduce hot spots
• Acts as a heat shield to protect the liner and adjacent components from direct radiant heat
• Helps maintain proper clearance and airflow around the element
• Damage or a missing baffle can lead to uneven temperatures, localized discoloration/scorching, or a burning smell

• Disconnect power at the breaker or unplug the appliance; allow it to cool completely
• Access the heater area; remove the screws or clips securing the existing baffle and retain the hardware
• Position the new baffle in the same orientation; ensure it does not contact the heating element
• Restore power and test operation

This hinge secures the door to the cabinet and provides a smooth pivot. Replacing a bent or worn hinge restores proper alignment and reliable latching so the door opens easily and closes securely.

• Provides the pivot point for the door to open and close
• Supports door weight and keeps it aligned with the latch/strike
• Wear or damage can cause sagging, rubbing, or squeaking
• A misaligned door may not engage the door switch, preventing the cycle from starting

• Disconnect power before servicing; shut off gas supply
• Support the door before removing mounting screws to avoid strain or damage
• Note hinge orientation; transfer any spacers/shims and reuse existing hardware
• Align the hinge, snug screws, then tighten fully and test door operation

Evaporator insulator that surrounds the evaporator assembly to reduce heat transfer and help limit frost buildup. Replacing damaged insulation helps maintain consistent temperatures and prevents excess moisture inside the freezer or refrigerator. What it does:

• Insulates and protects the evaporator area — common signs: visible frost or ice buildup and inconsistent cooling.
• Helps reduce vibration-related noise from evaporator components — common sign: rattling or buzzing.
• Prevents cold-air leakage into cabinet walls to support efficient cooling — common sign: warm spots or extended run times.
• Restores proper airflow pathways around the evaporator to help the system cycle normally.

• Disconnect power to the appliance before beginning any repair.
• Access may require removal of interior panels or the evaporator cover; follow OEM service instructions.
• Handle the insulation gently to avoid tearing or compressing it; use only manufacturer-recommended adhesives or fasteners if needed.

This is a suspension spring for select washers. It supports and stabilizes the wash tub during spin and agitation to reduce vibration and noise, helping the machine run smoothly.

• Supports the tub within the cabinet to control movement
• Helps reduce excessive vibration, banging, or walking during spin
• Addresses symptoms like out-of-balance loads, noise, or shaking
• Loss of tension, stretching, or breakage can require replacement

• Unplug the washer and shut off water supply before repair
• Access typically requires removing the top or front panel; support the tub to relieve spring tension
• Wear gloves and eye protection; springs are under tension
• Replace any damaged or missing suspension components in pairs or as required.