Kenmore Refrigerator 596.76054703 (59676054703, 596 76054703) Parts

Pulled out storage bin Removed side track rail covers Popped off gear from holding clip Installed drive shaft Installed rail cover and storage bin Only took about 15 minutes Read more

Replaced the defrost thermostat and heater and the refrigerator was working again. Read more

I bought the listed condenser fan motor for my Maytag refrigerator. Access to the condenser fan is by removing sheet metal screws of bottom panel with 1/4 in. nut driver. Condenser fan is on left side of rear access area. Remove electrical connector by pressing-in connector release tab with thumb fingernail and pulling on connector. Remove three mounting screws with 5/16 nut driver. Work fan out to the right past the compressor. I used a pair of pliers, as a lever, behind the plastic fan blades... Read more

Touch up paint Read more

Replaced It With New One Read more

Took off the freezer door, took off the top hinge on the refrigerator door, replaced the handle, re-installed the top hinge and the freezer door. This is a two person job - one to remove the top hinge and replace the handle, while a second person holds the refrigerator door in place. Replacing the handle was easy. The most irritating part was figuring out what parts to order. The drawing of the refrigerator door (Drawing # 4) used to figure out what parts to order was not clear. I paid $8... Read more

I watched the video on how to replace the ice maker and the replaced it with zero problems. Excellent help in trouble shooting problem and installation video further assisted in ease of installation. Read more

I ordered parts and replaced them. Service was great and fast, plus original parts. Thanks Read more

• Freezer not defrosting

My unit has a bottom freezer that is a drawer. I had to remove the drawer, rack, glides, glide tracks, and ice maker to remove the rear panel. This was a little difficult but after researching a few videos on line I learned some tricks that made it easier. I used a hair dryer to melt the ice. This is best done with 2 people having one at the back to sponge the water into a bowl from the pan to avoid a water mess. Using a bolt meter I checked the heating element and found it had continuity. I... Read more

There are videos on You Tube,. After removing the bottom basket, you remove the entire drawer including the door together with it, by using a screwdriver to depress the white clip on each drawer slide which releases the slide from body of the freezer. Once you pull our the entire drawer, you will need to drill out a rivet to remove the old slide. You will need a rivet gun to attach the new slide. Read more

All I needed was a $5 piece to fix my fridge, but without it I couldn't even us it. I ordered the part after 4:00 pm and had the new part shipped from Kentucky to NJ and had it by 10:00 am the next morning! Amazing! Great company. Read more

Had to take the back cover off. It was very tight to remove the fan that sat in the drip pan but did get it off, was able to apply the same level of cursing and got the new pan installed, installing the drain tube was a breeze. Found the parts price very reasonable. Hoping the Whirlpool redesigned the pan so I won't have to do it ever again. I was surprised at how bad the quality of their original part was. Probably saved myself $150.00 on buying the part and doing it myself Read more

• Leaking

I have a Whirlpool Side-by-side Model ED22PWXBW01. A year ago, the ice cubes started freezing together in the rear of the ice bin for no apparent reason. Although the problem started off small, it gradually grew much worse, and finally I could see water dripping out of the ice mold and into the bin during the fill cycle. Re-levelling the refrig didn’t help, nor did adjusting the cube size / fill level. With guidance from the video, I removed the icemaker from the wall of the freezer. The... Read more

Ordered replacement valve and also roller assembly for right side (as the leveling leg would not turn). Parts were installed and are working well. Read more

I called Sears to schedule a service call for Sat. Morning. At 11:00 a.m. A service man called and said he was going to do the service call (the original tech was going to be delayed), so he had been scheduled instead. He had another call before he could get to me (an hour drive one way And he would get lunch and see me later. I asked him about how long it might take, he said they do not charge by the hour. He said he couldn't remember for sure, but it was between $200.00 and $250.00, but... Read more

First had to clean inside the empty freezer, that was the hard part. removed old gasket and cleaned inside the track in the door. had the new gasket well warmed and in the right shape. put new gasket in track. seating it firmly. It was very easy. I did watch a couple of online videos to get the general idea of what it detailed. While I was at it I cleaned the coils with the brush I also bought with the gasket, worked great. all in all if you get organized before hand and take your time,... Read more