Kenmore Refrigerator 596.77532702 (59677532702, 596 77532702) Parts

Evaporator shroud cover for refrigerators. Encloses the evaporator coil assembly. Replace if cracked, broken, or missing to restore proper airflow.

Cross-support brace that reinforces the crisper cover on 36-inch models. Replace if broken, missing, or cracked to prevent cover sagging and keep bins aligned.

Replace your refrigerator's door hinge bushing to restore smooth door movement and eliminate noise. Guides and cushions the hinge to reduce friction and wear.

Supports and guides the upper freezer shelf for smooth sliding. Replace if shelf binds, sags, or tips when loaded. Confirm fit with your model number.

Condensate drain pan collects water under your refrigerator. Replace if cracked, leaking, or damaged to prevent floor water pooling and spillage.

This support bracket holds your refrigerator's pantry drawer in the proper position for smooth operation. It prevents the drawer from sagging and ensures proper alignment with door seals. Replace if your pantry drawer won't slide smoothly or appears to hang unevenly.

This circular component guides and directs water or ice from the dispenser to the user's container. Located in the refrigerator door dispenser area, replacement is needed when dispensing becomes inaccurate, messy, or completely blocked.

This temperature control bar is the actuator used to adjust and regulate the appliance's internal temperature, restoring proper temperature response for the bar/beverage control system. It provides a direct replacement for the OEM control bar assembly. What it does:

• Transfers user temperature adjustments to the control mechanism so the appliance reaches the set temperature
• Restores correct temperature changes when the control knob or selector fails to respond
• Helps address symptoms like incorrect temperature readings, temperature not changing, or unstable cooling behavior
• Works with the existing control housing and selector components to re-establish normal operation

• One temperature control bar

• Disconnect power before servicing to avoid electric shock
• Handle the part and surrounding components carefully to avoid damaging clips or wiring
• You may need to remove interior panels or the control housing to access the part;
• Verify the part number on your existing component before installation

This seal strip replaces a worn or damaged door gasket edge to restore a proper seal and help the appliance maintain temperature and operate quietly. It's a direct-fit service part used where a continuous seal is required. What it does:

• Provides a flexible barrier along the door/frame to reduce air leaks and heat/cold loss
• Helps prevent moisture buildup and improves energy efficiency when sealing is restored
• Reduces rattling and vibration caused by a compressed or torn seal edge
• Commonly replaced when the strip is torn, missing, or no longer adheres properly

• One seal strip

• Disconnect power to the appliance before servicing to avoid electrical or burn hazards
• Clean and dry the mounting surface; remove old adhesive or residue for best adhesion
• Align the strip carefully and press firmly; allow any adhesive to cure per manufacturer instructions

This hinge shim adjusts the alignment and spacing of your refrigerator door for proper closure. It ensures the door seals correctly and maintains proper clearance during operation. Replace it if your refrigerator door doesn't close properly, has uneven gaps, or if the door sags and doesn't align with the cabinet.

This slide temperature control is the user-access interface that moves the thermostat connection to select dryer heat levels. It restores responsive, indexed temperature selection for standard slide-style dryer controls. What it does

• Moves the internal contact to select low/medium/high heat settings for the dryer
• Replaces worn or loose slider that causes inconsistent or stuck temperature selection
• Helps correct symptoms such as inability to change heat level, intermittent temperature changes, or a slider that feels loose or won't stay in position
• Works as the mechanical interface between the console knob/lever and the dryer's control assembly

• One slide temperature control (single slider assembly)

• High-level replacement for users comfortable removing control consoles; disconnect power before service
• Handle control panel clips and trim carefully to avoid cracking plastic bezels
• Verify proper seating and alignment of the slider on the control shaft before reassembly

This is a clear or translucent plastic bin that mounts on the inside of the refrigerator door, designed to store smaller items like deli meats, cheese, or snacks in the chiller section. It snaps or slides onto the door liner rails for easy removal and cleaning. Replace this bin if it is cracked, broken, or if the mounting tabs have snapped off and it no longer stays securely in place.

Replacement screw for securing brackets, panels, trim, and internal assemblies. Needed when fasteners are missing, stripped, or rusted to restore stability.

White refrigerator door handle that slides onto door-mounted screws. Replace your cracked, broken, or missing handle to restore door functionality.

Ice dispenser not working or making grinding noises? This auger motor drives the spiral shaft that moves ice from the bin to the dispenser chute.