Kenmore Dishwasher 665.13014K110 (66513014K110, 665 13014K110) Parts

This replacement screw secures panels, brackets, and other components in your appliance to keep them aligned and rattle-free. Replacing worn, stripped, or missing hardware restores a tight fit and helps maintain safe, quiet operation.

• Fastens panels, brackets, or internal parts to the cabinet/frame
• Helps maintain alignment to reduce vibration and rattling
• Replaces lost, stripped, or corroded screws
• Common symptoms: loose panels/trim, rattles, or a screw that won't tighten

• Disconnect power; shut off water or gas if applicable
• Match thread and length to the original; replace one at a time to keep alignment
• Start threads by hand to avoid cross-threading; use the correct driver
• Tighten snugly—do not overtighten, especially into plastic or thin sheet metal

Fix dishwasher not heating or melted terminals with this heater terminal nut. Secures the heating element wire connection to prevent arcing and leaks.

This cap is a small protective cover used on select appliances to close off an opening or fastener. Replacing a damaged or missing cap helps keep out debris and moisture while restoring a clean, finished appearance.

• Covers an exposed opening or fastener to protect internal components
• Helps keep out dust, moisture, and spills
• Restores a clean, finished look and prevents snags
• Replace if the original cap is cracked, missing, discolored, or won't stay seated

• Disconnect power and, if applicable, shut off water or gas before service
• Remove the old cap by pulling straight off or unthreading, as designed
• Align the new cap and press or thread into place without forcing
• Verify a secure fit before restoring power and connections

Replace worn or cracked door spring bushings that secure the tension springs on your dishwasher door hinge assembly. Essential for smooth door operation.

Dishwasher stopping mid-cycle or not starting? A cracked door switch bracket prevents proper door detection. DIY repair in 10-30 minutes with video help.

Fixes broken heating element brackets causing sagging or rattling noises in your dishwasher. Simple snap-on replacement restores proper element alignment.

Fix a dishwasher that stops mid-cycle with a blinking start light. This door interlock switch restores reliable operation. 20-minute DIY repair.

Dishwasher not heating or drying properly? This heater probe shield protects temperature sensors and nearby components from heat damage for accurate sensing.

Bottle with brush. Color: Black. Size: 0.6 fl.oz.

This factory-spec screw secures panels and components in your appliance. Replacing a missing or stripped fastener restores a tight, rattle-free fit so parts stay aligned and operate as designed.

• Fastens brackets, panels, and internal components to their mounting points
• Maintains alignment and reduces vibration during operation
• Replaces missing, worn, rusted, or stripped hardware
• Helpful when you notice rattling, loose panels, gaps, or parts shifting out of position

• Disconnect power; shut off water or gas supply if applicable
• Align the part being secured and remove any damaged hardware
• Hand-start threads to avoid cross-threading; tighten with the correct driver
• Do not overtighten; verify the assembly is secure and operates freely

Replacement mounting screw for dishwashers and ranges. Secures panels, brackets, and internal components when original hardware is stripped, missing, or corroded.

Fix dishwasher leaks at the bottom with a new sump and seal assembly. Replaces cracked sumps or worn seals causing water pooling under the unit.

Size: 1/4 inch hex head, 10-12 x 1/2 inch.

This hose clamp secures dishwasher hoses to fittings and ports to maintain a tight, leak-resistant seal. Replacing a worn clamp helps prevent drips and loose connections that can cause water under the unit.

• Secures drain or circulation hose to the pump, sump, or other dishwasher fittings
• Helps maintain a watertight seal at hose connection points
• Can help resolve water dripping from a hose joint or a loose hose
• Replace if corroded, deformed, cracked, or no longer holds tension

• Disconnect power and turn off the water supply before servicing
• Place a towel or shallow pan to catch residual water when removing hoses
• Fully seat the hose on the fitting, position the clamp over the barb/connection, and secure firmly
• After reassembly, run a brief fill/drain and check all connections for leaks

Replace your dishwasher's console door seal when you notice water leaks or gaps between the console and door. Verify fit with your model number.

Fix dishwasher leaks from the tub floor with this overfill protector housing. Guides the float and positions the switch actuator to restore protection.