Kenmore Dishwasher 665.13243K901 (66513243K901, 665 13243K901) Parts

The Check Valve is an OEM part for Whirlpool dishwashers. This small but crucial component prevents backflow of water into the dishwasher, ensuring that dirty water is properly drained and does not contaminate clean dishes. It plays a vital role in maintaining the efficiency and hygiene of the dishwasher by directing water flow correctly during the wash and drain cycles.

Causes of a bad check valve can include blockages from food particles, mineral deposits from hard water, or wear and tear over time. These issues can impede the valve's function, leading to ineffective drainage and potential backflow problems.

Symptoms of a bad check valve include:

• Water not draining properly from the dishwasher
• Dirty water pooling at the bottom of the dishwasher
• Unpleasant odors from standing water
• Residue or food particles left on dishes after a wash cycle

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

The Air Inlet is an OEM part for Whirlpool dishwashers. This component allows fresh air to enter the dishwasher during the drying cycle, helping to reduce moisture and improve the efficiency of the drying process. By introducing outside air, the air inlet aids in removing humidity from inside the dishwasher, ensuring dishes come out dry and free from water spots.

Causes of a bad air inlet can include clogging from debris or mineral deposits, damage from regular wear and tear, or mechanical failures within the part itself. A faulty air inlet can lead to poor drying performance and increased moisture inside the dishwasher.

Symptoms of a bad air inlet include:

• Dishes remaining wet after the drying cycle
• Increased humidity inside the dishwasher after the cycle is complete
• Water spots on dishes and glassware
• Unusual noises during the drying cycle

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

The Dispenser Cap is an OEM part for Whirlpool dishwashers. It covers the detergent dispenser, ensuring that the detergent remains securely in place until it is dispensed during the wash cycle. This cap plays a vital role in the cleaning process by preventing detergent from spilling or dispersing too early, thereby optimizing the efficiency of the dishwasher.

Over time, the dispenser cap can become worn or damaged due to regular use, exposure to detergents, or accidental impacts. If the cap is compromised, it can lead to detergent leakage and ineffective cleaning.

Symptoms of a bad dispenser cap include:

• Detergent not dispensing properly
• Residual detergent left in the dispenser after the cycle
• Leaks or drips around the dispenser area
• Inefficient cleaning of dishes

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

The Dishwasher Heating Element is an OEM replacement part for Whirlpool dishwashers. It safely generates heat to sanitize dishes and raise water temperatures during hot drying cycles. A functioning heating element ensures thorough cleaning and reduces the risk of damage from moisture left behind.

Causes of a bad heating element usually relate to standard wear and deterioration of wiring insulation or coil materials after extended usage cycles. Surface scale can obstruct heat transfer if not periodically removed.

Symptoms of a bad heating element include:

• Dishes not getting fully dry
• Moisture remaining in low areas after cycles
• Inability to select high-temperature settings
• Cycles that don't reach the required sanitization temps

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore dishwashers.

The Lower Dishrack Wheel Assembly is an OEM part for Whirlpool dishwashers. This assembly attaches to the lower dishrack, allowing it to glide smoothly along the dishwasher tracks during loading and unloading. 

Over time, the lower dishrack wheel assembly can become faulty. Causes of a bad wheel assembly can include regular wear and tear, damage from heavy loads, or exposure to high temperatures and detergents. A malfunctioning wheel assembly can make it difficult to move the lower dishrack, affecting the convenience and functionality of the dishwasher.

Symptoms of a bad lower dishrack wheel assembly include:

• The lower dishrack not sliding smoothly or becoming stuck
• The dishrack being uneven or lopsided
• Noise or resistance when moving the lower dishrack
• The wheel appearing cracked, broken, or missing

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

The Upper Dishrack Rail is an OEM replacement part for Whirlpool dishwashers. It guides upper racks in and out for easy access to dishes. 

Causes of faulty rails can include worn rollers, broken clips, or stress cracks in modules after repeated cycles. 

Symptoms of a bad upper dishrack rail include:

• Difficulty inserting or removing the upper rack smoothly   
• Off-track movement that impacts washing coverage
• Detached ends or segments that compromise stability

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

The Filter Assembly is an OEM part for Whirlpool dishwashers. This component is responsible for trapping food particles and debris, preventing them from recirculating during the wash cycle and ensuring that dishes come out clean. 

Causes of a bad filter assembly can include accumulated debris, regular wear from repeated use, or damage from harsh cleaning agents. A compromised filter can reduce the dishwasher’s cleaning performance and lead to buildup inside the machine.

Symptoms of a bad filter assembly include:

• Dishes not being cleaned properly
• Unusual noises during the wash cycle
• Slow drainage or standing water in the dishwasher
• Visible damage or clogging of the filter

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

The Air Vent Gasket is an OEM part for Whirlpool dishwashers. It is designed to seal the air vent, preventing water from leaking out during the dishwasher's operation. This gasket plays a critical role in maintaining the efficiency and effectiveness of your dishwasher by ensuring a watertight seal around the air vent, which is essential for the proper function of the venting system.

Causes of a bad Air Vent Gasket can include wear and tear over time, leading to cracks or deterioration, improper installation, which may result in a poor seal, or damage from harsh cleaning chemicals.

Symptoms of a bad Air Vent Gasket include:

• Water leaking from around the dishwasher's door.
• Dishes not drying properly due to compromised venting.
• Visible signs of wear or damage on the gasket itself.

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

This replacement panel restores your appliance's original look while shielding internal components. Install a new panel to replace a dented, cracked, or missing piece and keep the assembly secure, aligned, and protected.

• Covers and protects internal parts while restoring the exterior finish and fit
• Provides the designed mounting surface for trim/handles; helps maintain alignment
• Replace when the panel is dented, cracked, warped, rusted, or mounting tabs are broken
• Helps resolve loose or rattling panels and visible gaps or misalignment

• Disconnect power; turn off water or gas supply if applicable
• Wear gloves and protect finished surfaces; handle carefully to avoid bending or scratching
• Transfer and reuse original screws, clips, insulation, and trim as directed by your service manual
• Fit and alignment before fully tightening fasteners

The Insulation is an OEM part for Whirlpool dishwashers, specifically engineered to enhance the appliance's efficiency by reducing heat loss and minimizing noise. This insulation wraps around the dishwasher, acting as a barrier that keeps heat within the appliance during cycles and dampens the sound of its operation, making for a quieter kitchen environment.

Causes of a bad insulation part can include wear and tear over time, moisture damage leading to mold or mildew buildup, or physical damage from pests or mishandling during installation or repairs. 

Symptoms of inadequate insulation include:

• Noticeable increase in the dishwasher's noise level
• Exterior surfaces of the dishwasher feeling warmer than usual
• Longer wash cycles due to inefficient temperature maintenance

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

The Float Switch Kit is an OEM part for Whirlpool dishwashers. It includes the float and the switch mechanism that monitors and controls the water level inside the dishwasher. The float switch ensures that the dishwasher does not overfill by signaling the water inlet valve to shut off the water supply once the appropriate level is reached.

Causes of a bad float switch can include debris or mineral buildup, wear and tear over time, or electrical failures within the switch mechanism. A malfunctioning float switch can lead to water overfilling, which may cause leaks and inefficient washing performance.

Symptoms of a bad float switch kit include:

• Dishwasher overfilling with water
• Water leaks during operation
• Dishwasher not filling with enough water
• Error codes related to water levels

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

The Side Mounting Bracket Kit is an OEM part for Whirlpool dishwashers. It provides a secure and stable installation by mounting the dishwasher to the adjacent cabinetry or walls.

Causes of a bad Side Mounting Bracket Kit can include missing or damaged components, improper installation, or wear and tear over time.

Symptoms of a bad Side Mounting Bracket Kit include:

• The dishwasher rocking or shifting during operation
• Gaps or spaces between the dishwasher and surrounding cabinetry
• Potential safety hazards due to an improperly secured dishwasher

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

The Nut is an OEM part for Whirlpool dishwashers. This nut secures the float switch, a key component in regulating the water level within the dishwasher. The float switch ensures your dishwasher does not overfill by triggering the water to stop once it reaches a certain level. 

Over time and with regular use, the nut that holds the float switch in place can become loose or damaged. This could potentially allow water to seep through gaps, leading to leaks, or could cause the float switch to malfunction, affecting the dishwasher's ability to regulate water levels accurately.

Symptoms of a faulty Nut include:

• Water leaks from the base of the dishwasher 
• The dishwasher overfills or underfills 
• Unusual noises during operation 

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

The Hose Clamp is an OEM part for Whirlpool washing machines. This clamp secures the hose in place, ensuring a tight connection and preventing leaks during operation. It is essential for maintaining the integrity of the washing machine's water system, securing hoses that carry water to and from the washer.

Common causes of a bad hose clamp include rust, physical damage, or loosening from repeated tightening and loosening.

Symptoms of a bad hose clamp include:

• Water leaks around the hose connection points
• The hose slipping off the fitting
• Visible rust or wear on the clamp
• Difficulty in tightening the clamp to secure the hose

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and some Kenmore models.

The Lower Spray Arm Support is an OEM replacement part for Whirlpool built-in dishwashers. Attached underneath the wash arms enclosure, this bracket securely anchors the rotating lower spray arm inside the lower dishrack.

Causes of failure involve cracking or stripping of securing clips allowing excessive movement during high-pressure spray cycles. Mineral buildup over time can also obstruct smooth operation.

Symptoms consist of:

• Detached lower spray arm failing to thoroughly rinse lower rack dishes
• Abnormal noises and vibrations from mobility during operation
• Ineffective cleaning even on light soil levels
• The lower spray arm not rotating or spinning freely during wash cycles

This is a genuine Whirlpool OEM replacement this part is also compatible with Maytag, Jenn-Air and some Kenmore models.

To order seal use WP8268340.

The Door Latch Bracket is an OEM part for Whirlpool dishwashers. This bracket is crucial for securing the dishwasher door latch, ensuring that the door stays closed during operation. A properly functioning door latch bracket helps maintain a tight seal, preventing water leaks and enabling the dishwasher to run efficiently.

Causes of a bad door latch bracket can include regular wear and tear, damage from repeated door openings and closings, or physical impact that compromises its integrity. A malfunctioning bracket can lead to door alignment issues and ineffective sealing.

Symptoms of a bad door latch bracket include:

• The dishwasher door not latching or staying closed
• Water leaking from around the door during cycles
• The door appearing misaligned or loose
• Difficulty starting the dishwasher due to improper door closure

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

Handle not included. For black handle use WP8534984. For white handle use WP8534985. For bisque use 8534986