Kenmore Dishwasher 665.13823K600 (66513823K600, 665 13823K600) Parts

Controls water level and prevents overfilling in your dishwasher. Replace if you notice leaking or overflow issues. Confirm fit using your model number.

Internal rear feed cap for dishwasher spray arm system. Replace if damaged, cracked, or water leaks from the rear feed area. Confirm fit with your model.

Fix a dishwasher that won't fill properly or overfills with this overflow switch lever. Restores water level detection. DIY-friendly repair.

This adjustable manifold is a direct-fit replacement that secures and positions the appliance's manifold assembly so related components line up and function correctly. It restores proper alignment and reliable operation when the original is bent or worn. What it does:

• Provides a mounting surface and adjustable position for the manifold assembly and attached components
• Helps maintain correct alignment so burners/valves operate smoothly
• Restores fit when the original manifold is damaged, bent, or loose
• Resolves symptoms such as uneven burner operation, ignition difficulty, or mechanical misalignment

• Turn off power and shut off gas supply before starting work
• Handle and align carefully to avoid bending; secure with the OEM fasteners
• Check seals and connections after installation; test operation per manufacturer instructions

Replacement outer door panel for your dishwasher. Installs on the front exterior of the door. Order when your panel is cracked, dented, or damaged.

Filters lint and debris from wash water before reaching the drain pump. Replace if cracked or clogged to restore proper draining. Confirm fit by model.

Color: Biscuit. Screw for lower toe panel. For black screw use WP302868, for white screw use WP3400836.

Color: White. Size: 1 qt. can. Acrylic appliance paint.

This is the exterior-facing panel that forms the visible front surface of the dishwasher door. It provides a finished appearance and helps protect the internal door components, including insulation and wiring. Replace this panel if it is dented, scratched, rusted, or if the finish has deteriorated significantly.

Flat washer for dishwasher fasteners. Distributes load and prevents loosening at mounting points. Replace when worn or missing to reduce vibration. Confirm fit with your model number.

The Thermostat Clip is an OEM part for Whirlpool dishwashers. It plays an important supporting role by securely fastening the thermostat sensor inside the wash chamber. 

Symptoms of a faulty Thermostat Clip can include:

• Fluctuating or inconsistent water temperatures between cycles 
• Inability to properly detect temperature for desired heat levels
• Longer cycle times needed for reaching required temperatures
• Strange sounds or condensation around thermostat connection

Causes could arise from typical wear and tear stresses weakening plastic retaining clips. Exposure to harsh detergents may also erode clip material integrity over time.

This OEM replacement part is compatible with KitchenAid, Jenn-Air, Kenmore, and select Hotpoint and Roper dishwasher models as well. 

Access panel covers the base of your dishwasher, concealing wiring and mechanisms. Replace if cracked, broken, or missing after installation.

Shield for dishwashers. Protects internal components from heat and water damage. Replace if cracked, broken, or missing to maintain proper coverage.

Protective cover that installs over your dishwasher's capacitor. Replace if cracked, broken, or missing to shield the capacitor from debris and contact.

This is the lower front panel that mounts beneath the dishwasher door, concealing the motor, wiring, and plumbing connections underneath the unit. It snaps or screws into place and gives the dishwasher a clean, finished look. Replace this panel if it is damaged, warped, or missing, which can leave internal components exposed to dust and debris.

This is a small plastic or rubber fitting that secures the power cord where it enters the dishwasher's junction box or base. It prevents the electrical wiring from being pulled, kinked, or damaged by absorbing tension on the cord. Replace this part if it is cracked or missing, which can leave wiring exposed and vulnerable to damage during installation or use.