Kenmore Dishwasher 665.14213K901 (66514213K901, 665 14213K901) Parts

The Impeller is an OEM part for Whirlpool brand dishwashers. Located within the dishwasher sump assembly, this plastic component utilizes rotating blades to circulate wash water throughout cycles.

Causes of a bad impeller can include cracking or damage from minerals over time, chunks of food debris jamming the blades, or normal wear on plastic.

Symptoms of a faulty impeller include: 

• Inadequate water circulation yielding poor cleaning 
• Food particles or utensils not fully rinsed
• Loud clicking or grinding noises mid-cycle
• Error codes relating to low water pressure

Replacing the impeller restores optimum water flow for Whirlpool dishwashers. Proper circulation using the OEM replacement ensures all portions of dishes and cycles receive sufficient water volume. Compatibility also includes Maytag, Jenn-Air, Amana, Magic Chef, and other brands.

Size: 1/4 inch hex head, 10-12 x 1/2 inch.

Pump housing only. For a complete pump and motor assembly, order WPW10247394.

This dishwasher door spring restores proper counterbalance so the door opens smoothly and doesn't drop. The premium version provides the factory-specified tension used on select models for consistent, controlled door movement.

• Counterbalances the door for smooth opening and closing
• Helps prevent the door from slamming open or feeling heavy
• Supports stable, mid-position hold when springs are intact and matched
• Common signs of failure: door drops quickly, is hard to lift, or won't stay in position

• Disconnect power and water; remove the toe kick/access panel to reach the springs
• Note which frame/hinge holes the old spring used and install the new spring in the same positions to match tension
• Use pliers to relieve tension safely; if your model uses two springs, replace both for balanced operation
• Wear gloves and eye protection; keep hands clear of moving hinges

This upper draw bar is a door-latch linkage piece used in dishwashers. It connects the handle/actuator to the latch mechanism so the door closes securely and the door switch engages, allowing the cycle to start reliably.

• Links the door handle/actuator to the latch for positive closure
• Helps ensure the door switch is engaged so the unit will run
• Restores proper latch alignment and handle feel
• Common symptoms: door won't latch or pops open, dishwasher won't start, must push/hold door to run, loose or floppy handle

• Disconnect power at the breaker; turn off water supply if working near the inlet
• Open the door and remove inner-door screws to access the latch linkage
• Note bar orientation; transfer any clips/bushings and reuse existing hardware
• Reassemble and check latch engagement before running a cycle

Size: 7 foot long.

This replacement screw secures appliance panels and components so they stay tight and aligned. Replace a missing, rusty, or stripped fastener to restore a solid hold and reduce vibration or rattling during operation. What it does:

• Fastens and secures panels, brackets, trim, or internal components as specified for your model
• Replaces missing, corroded, or stripped hardware to restore a proper fit
• Helps prevent vibration, rattling, and misalignment caused by loose fasteners
• Addresses issues like a loose panel/handle or a screw head that's rounded off

• 1 screw

• Disconnect power; if applicable, shut off gas and water before servicing
• Use the correct driver size; start by hand to avoid cross-threading
• Tighten snugly—do not overtighten into plastic or thin sheet metal
• Keep track of original screw locations and lengths during reassembly

This tub wheel mount secures the rack support roller to the dishwasher tub wall so racks roll smoothly. Replace a cracked or loose mount to restore smooth rack movement and prevent binding or sagging during loading and unloading.

• Secures the tub roller/wheel to the dishwasher's inner tub wall
• Provides a stable point so the rack glides smoothly on its track
• Helps keep the rack level and properly aligned
• Common symptoms: rack hard to slide, tilts or drops, scraping/grinding when moving the rack

• Disconnect power and water supply before servicing
• Pull the rack forward to access the mount on the tub sidewall
• Remove the retaining fastener or release locking tabs, then install the new mount in the same orientation
• Ensure the wheel engages the track and test rack travel for smooth operation

This adjustable leveling leg threads into the appliance base to set height and stabilize the cabinet. Replacing a worn or missing leg helps stop rocking and vibration and helps maintain proper alignment for reliable operation.

• Provides adjustable support at one corner of the appliance
• Helps level the unit for correct alignment with floor or cabinetry
• Reduces rocking, vibration, and rattling noises
• Replaces stripped, bent, cracked, or missing leg

• Disconnect power and, if applicable, shut off water before servicing
• Carefully support or brace the appliance to access the base safely
• Start the new leg by hand to avoid cross-threading; adjust height gradually
• Use a level to check side-to-side and front-to-back, then recheck after positioning

This vent screen covers the dishwasher door vent, allowing steam to escape while blocking food particles and debris. Replacing a damaged or missing screen helps maintain proper airflow and can reduce moisture and odors around the vent area.

• Screens the door vent to keep debris out of the vent duct and fan path
• Maintains airflow for venting steam during the dry cycle
• A clogged, cracked, or missing screen may lead to moisture at the vent, odors, or reduced drying performance
• Replace if warped, broken, or lost during service

• Disconnect power to the dishwasher at the breaker before servicing
• Open the door and remove inner-door screws to access the vent assembly
• Remove the old screen, seat the new screen fully and evenly, then reassemble without overtightening
• Run a short cycle and check the vent area for proper airflow and moisture

Color: White. Includes insulation. Other colors: For almond use WP3384157, for biscuit use WP3384157, for black use WP3379920.

This replacement cam converts rotational motion into the precise movement needed by the appliance's linkage or latch assembly, restoring proper mechanical timing and part engagement. Use this cam to replace a worn, broken, or stripped cam and help return reliable operation. What it does

• Transfers motor or shaft rotation into controlled push/pull motion for linkages or latches
• Restores correct timing and movement when a plastic cam is cracked, worn, or slipping
• Helps resolve symptoms like intermittent or failed door/latch action, noisy operation, or improper cycle sequencing
• Works as a like-for-like mechanical replacement when the OEM cam has failed

• One replacement cam (single piece only)

• Disconnect power (and water supply if applicable) before beginning any repair
• Inspect mating shafts, linkages, and fasteners; replace any damaged hardware to prevent repeat failure

This grate captures heavy soils and debris at the bottom of the washer tub to help reduce re-deposition on clothing and keep the drain area clearer. Restores proper soil separation for more consistent wash results. What it does:

• Traps heavy dirt and debris so it doesn't recirculate onto clothes during the wash.
• Helps keep the drain/under-tub area clearer, reducing the chance of clogs.
• Supports proper water flow and soil separation for improved cleaning performance.
• Common symptoms indicating a failing or missing part: clothes still look soiled after a cycle, visible debris in the tub, or frequent drain blockages.

• One grate

• Disconnect power and shut off water before servicing the washer.
• Drain the tub and remove any agitator or tub components required for access.
• Use basic hand tools; avoid forcing parts or over-tightening plastic components.

Replacement 8-32-thread screw used to secure panels, brackets and small components in compatible household appliances. Restores missing or stripped fasteners so panels and parts stay firmly attached during normal use. What it does:

• Secures trim, panels, brackets and control housings to maintain proper assembly.
• Replaces missing or damaged screws that can cause rattling, loose panels or misaligned components.
• Fits locations that require an 8-32 threaded fastener; correct length and head style for your application.
• Helps restore stable, vibration-free operation when worn or stripped fasteners are replaced.

• Disconnect power and water before servicing; wear eye protection and gloves.
• Use the correct screwdriver or driver bit to avoid stripping the screw head.
• Do not overtighten—turn until snug and secure to avoid damaging threads or surrounding parts.
• If the original used a washer or nut, reuse or replace as needed and the screw length and head type match the original.

This tower protector is a small plastic cover that fits over the dishwasher's spray tower. It helps keep dishes and utensils from obstructing the tower's spray outlets so water can circulate properly for consistent cleaning.

• Shields the spray tower to prevent items from blocking water flow
• Helps maintain proper spray pressure and coverage to upper areas
• Replaces cracked, melted, or missing protectors that can lead to poor cleaning
• Common signs it's needed: protector is broken/loose, deformed, or repeatedly falls off; dishes aren't getting clean due to blocked spray

• Disconnect power and water before service
• Allow the dishwasher interior to cool
• Open the door, remove the lower rack, and snap the protector into place per the tower/rack design
• Verify it seats securely and does not interfere with the spray tower movement

Color: Black. Size: 12 oz. Acrylic appliance aerosol can spray paint.