Kenmore Dishwasher 665.15522000 (66515522000, 665 15522000) Parts

This replacement screw secures appliance panels and components so they stay tight and aligned. Replace a missing, rusty, or stripped fastener to restore a solid hold and reduce vibration or rattling during operation. What it does:

• Fastens and secures panels, brackets, trim, or internal components as specified for your model
• Replaces missing, corroded, or stripped hardware to restore a proper fit
• Helps prevent vibration, rattling, and misalignment caused by loose fasteners
• Addresses issues like a loose panel/handle or a screw head that's rounded off

• 1 screw

• Disconnect power; if applicable, shut off gas and water before servicing
• Use the correct driver size; start by hand to avoid cross-threading
• Tighten snugly—do not overtighten into plastic or thin sheet metal
• Keep track of original screw locations and lengths during reassembly

This tub wheel mount secures the rack support roller to the dishwasher tub wall so racks roll smoothly. Replace a cracked or loose mount to restore smooth rack movement and prevent binding or sagging during loading and unloading.

• Secures the tub roller/wheel to the dishwasher's inner tub wall
• Provides a stable point so the rack glides smoothly on its track
• Helps keep the rack level and properly aligned
• Common symptoms: rack hard to slide, tilts or drops, scraping/grinding when moving the rack

• Disconnect power and water supply before servicing
• Pull the rack forward to access the mount on the tub sidewall
• Remove the retaining fastener or release locking tabs, then install the new mount in the same orientation
• Ensure the wheel engages the track and test rack travel for smooth operation

This small check ball sits inside a check valve to allow one-way water flow. Replacing a worn or missing ball helps prevent backflow and supports reliable draining performance between cycles.

• Maintains one-way flow through the valve to stop water from returning after the pump stops
• Helps ensure complete, consistent draining
• A damaged, swollen, or missing ball can let water back up into the tub/sump
• Contribute to slow or intermittent draining and unusual gurgling/flow noises

• Disconnect power and shut off water before servicing
• Access the check valve assembly per your model's service information (commonly at the sump, pump outlet, or drain connection)
• Clean the valve seat/passage; remove debris that could prevent sealing
• Place the ball in the valve seat as shown in your model's parts diagram; reassemble and test for leaks and proper flow

Color: Almond

This adjustable leveling leg threads into the appliance base to set height and stabilize the cabinet. Replacing a worn or missing leg helps stop rocking and vibration and helps maintain proper alignment for reliable operation.

• Provides adjustable support at one corner of the appliance
• Helps level the unit for correct alignment with floor or cabinetry
• Reduces rocking, vibration, and rattling noises
• Replaces stripped, bent, cracked, or missing leg

• Disconnect power and, if applicable, shut off water before servicing
• Carefully support or brace the appliance to access the base safely
• Start the new leg by hand to avoid cross-threading; adjust height gradually
• Use a level to check side-to-side and front-to-back, then recheck after positioning

This vent screen covers the dishwasher door vent, allowing steam to escape while blocking food particles and debris. Replacing a damaged or missing screen helps maintain proper airflow and can reduce moisture and odors around the vent area.

• Screens the door vent to keep debris out of the vent duct and fan path
• Maintains airflow for venting steam during the dry cycle
• A clogged, cracked, or missing screen may lead to moisture at the vent, odors, or reduced drying performance
• Replace if warped, broken, or lost during service

• Disconnect power to the dishwasher at the breaker before servicing
• Open the door and remove inner-door screws to access the vent assembly
• Remove the old screen, seat the new screen fully and evenly, then reassemble without overtightening
• Run a short cycle and check the vent area for proper airflow and moisture

Comes with seal.

Color: White. Includes insulation. Other colors: For almond use WP3384157, for biscuit use WP3384157, for black use WP3379920.

Replacement 8-32-thread screw used to secure panels, brackets and small components in compatible household appliances. Restores missing or stripped fasteners so panels and parts stay firmly attached during normal use. What it does:

• Secures trim, panels, brackets and control housings to maintain proper assembly.
• Replaces missing or damaged screws that can cause rattling, loose panels or misaligned components.
• Fits locations that require an 8-32 threaded fastener; correct length and head style for your application.
• Helps restore stable, vibration-free operation when worn or stripped fasteners are replaced.

• Disconnect power and water before servicing; wear eye protection and gloves.
• Use the correct screwdriver or driver bit to avoid stripping the screw head.
• Do not overtighten—turn until snug and secure to avoid damaging threads or surrounding parts.
• If the original used a washer or nut, reuse or replace as needed and the screw length and head type match the original.

Screw: 8-16 x 3/8 inch.

Color: Black. Size: 12 oz. Acrylic appliance aerosol can spray paint.

Size: 8-18 x 1/2 inch.

This wet agent dispenser replaces the washer's liquid fabric softener dispenser to restore proper dispensing during the rinse cycle. It helps keep softener contained until the machine is ready to release it, improving rinse-time performance. What it does:

• Holds and releases liquid fabric softener (wet agent) into the rinse cycle
• Ensures softener is delivered at the correct time for even distribution
• Stops leaking or premature release when the dispenser housing is intact
• Commonly replaced when the dispenser cracks, clogs, or fails to dispense

• Disconnect power to the appliance before starting any repairs
• Access method varies by model; remove dispenser drawer or top panel per your model's service instructions
• Inspect surrounding seals and clips; replace if damaged to prevent leaks

Touch-up paint for repairing small chips, scratches and scuffs on painted appliance surfaces. Restores the appearance of localized damage so repaired areas better blend with the surrounding finish. What it does:

• Covers small chips and surface scratches to improve cosmetic appearance.
• Helps conceal finish wear on painted metal and plastic trim.
• Lets you spot-repair without replacing large panels or parts.
• Works for quick, visible fixes where full repainting isn't needed.

• Clean and dry the repair area thoroughly before applying; remove loose paint or rust.
• Test on an inconspicuous area first to confirm color match and compatibility.
• Apply sparingly in thin coats with a small brush or cotton swab; allow each coat to dry before adding more.
• Use in a well-ventilated area and keep out of reach of children; follow any handling instructions on the product label.

A pronged cup washer that secures and cushions mating parts on appliances, restoring proper fit and reducing wobble. Replaces worn or damaged cup-style washers to help maintain stable component alignment and reliable operation. What it does:

• Fits into a cup or socket to hold shafts, knobs, or trim pieces in place
• Pronged design grips the mounting surface to prevent rotation and slippage
• Helps reduce vibration and noise caused by loose or worn washers
• Commonly used when a knob, shaft, or trim feels loose or wobbly

• Disconnect power to the appliance before servicing to avoid shock or injury
• Remove the related knob or trim carefully to access the washer; note orientation for correct reassembly
• Press the washer fully into the cup or socket so the prongs engage the mounting surface
• Inspect the surrounding components for wear and replace any damaged parts

Size: 8-32 x 1/2 inch.