Kenmore Dishwasher 665.15592791 (66515592791, 665 15592791) Parts
Genuine Whirlpool part
By: Whirlpool
Part Number: WP8268874
This lower spray arm assembly circulates wash water from the pump to clean dishes on the lower rack. The integrated shield helps direct water flow and protect the arm from debris, restoring consistent wash coverage.
- Distributes high-pressure water across the lower rack for effective cleaning
- Shield design helps prevent debris intrusion and improves spray pattern
- Common failure signs: poor lower-rack cleaning, noisy or restricted rotation, cracked or warped arm, clogged spray holes
- Also addresses leaking or splashing caused by a damaged or misaligned arm/shield
What's included: One lower spray arm with attached shield Install notes:
- Disconnect power and turn off water supply before servicing
- Remove lower rack; lift off old arm assembly per model design
- Clear any debris from pump outlet and sump before installing
- Ensure the new arm spins freely and is fully seated; test for smooth rotation
Do-It-Yourself Stories from Customers like You
Dishwasher was noisy not cleaning well and spray arms were loose Steve S. • Rochester , MN • September 10, 2016
Replaced upper and lower spray arms, plus nylon bearings.
Read more
More
$70.76
- Compare At:
-
$84.91
- You Save:
-
$14.15
Genuine Whirlpool part
By: Whirlpool
Part Number: WP9740674
This drain cover gasket seals the drain/pump cover at the bottom of the dishwasher tub to keep wash water contained. Replacing a cracked or flattened gasket helps stop leaks from the base and protects nearby components.
- Creates a watertight seal between the drain cover and sump opening
- Helps prevent leaks onto the floor or into the dishwasher base during cycles
- Common signs of failure: puddles beneath the unit, dampness in the base, or a visibly hardened/cracked gasket
- Good practice to replace when the drain cover is removed for service to ensure a proper reseal
What's included: 1 drain cover gasket Install notes:
- Disconnect power and shut off water supply before servicing
- Remove the lower rack (and spray arm if required) to access the drain cover per your model
- Clean mating surfaces; install the new gasket evenly without twists
- Reassemble and run a short cycle while checking for leaks
Do-It-Yourself Stories from Customers like You
Debris got into the impeller and broke it Thomas L. • Westport , MA • November 30, 2014
Replaced the drain & wash impeller kit.
Read more
More
$5.95
- Compare At:
-
$7.02
- You Save:
-
$1.07
Genuine Whirlpool part
By: Whirlpool
Part Number: WP676455
Color: Grey. 4oz bottle with brush used for touching up damage to your dishracks. For blue use W10840471. For white use WP676453. For tips use 676458.
Do-It-Yourself Stories from Customers like You
Rusty tips on tops of posts in top and bottom racks of kitchen aid dishwasher James O. • Bedford , OH • July 04, 2016
Used the vinyl touch up paint on the tops of posts and slid vinyl tips over 130 posts. The paint acts as an adhesive to keep the tips secure.
Read more
More
$24.95
- Compare At:
-
$29.69
- You Save:
-
$4.74
Genuine Whirlpool part
By: Whirlpool
Part Number: WP3373234
This dishwasher door spring bushing—also called a door spring bearing—sits at the spring's frame anchor to provide a pivot and reduce wear. Replacing a worn bushing restores door balance and helps prevent the door from dropping or slamming open.
- Provides the pivot/anchor surface for the door spring at the cabinet frame
- Maintains balanced door opening and closing force
- Reduces friction, wear, and squeaks at the spring connection
What's included: Includes 1 bushing. Install notes:
- Disconnect power at the breaker and shut off water supply.
- Remove the toe panel and mounting screws; slide the dishwasher out slightly to access the door springs.
- Support the door, release spring tension, replace the bushing at the frame anchor, and reattach the spring.
- Inspect both sides and replace worn components in pairs to keep door tension even.
Do-It-Yourself Stories from Customers like You
The dishwasher door spring broke. Rachael T. • Junction City , OR • November 07, 2022
I ordered the parts, deciding that if one spring had broken, the other one should probably be replaced at the same time. I followed the suggestion of ordering the door spring bearing given on the ordering page, and since I had not yet pulled out the dishwasher, did not know that it was not used in this older model. However, the order arrived quickly (4 days), and they are genuine Whirlpool, made in the USA, parts. The access to the sides of the dishwasher where the springs are attached...
Read more
More
$6.95
- Compare At:
-
$8.27
- You Save:
-
$1.32
Genuine Whirlpool part
By: Whirlpool
Part Number: WP676453
Color: White. 4oz bottle with brush used for touching up damage to your dishracks. For blue use W10840471. For grey use WP676455. For tips use 675679
Do-It-Yourself Stories from Customers like You
Tines on my dishwasher rack was rusting rust was showing on my dishes Jean M. • Lenoir , NC • January 10, 2015
Ordered dishwasher rack tine tips and bottle of vinyl touch up paint. I applied the paint to each tine and then placed the tips on the tines. I waited a few hours before using my dishwasher to allow the paint to dry and allow the tips to stick to the tines.
Read more
More
$30.95
- Compare At:
-
$37.14
- You Save:
-
$6.19
Genuine Whirlpool part
By: Whirlpool
Part Number: 675679
Color: White. Includes 125 caps used to cover damaged tips on your dishracks. For blue order 12022. For grey order 676458. To attach these tine tips you will need to order the dishrack white touch-up paint WP676453.
Do-It-Yourself Stories from Customers like You
Tines on my dishwasher rack was rusting rust was showing on my dishes Jean M. • Lenoir , NC • January 10, 2015
Ordered dishwasher rack tine tips and bottle of vinyl touch up paint. I applied the paint to each tine and then placed the tips on the tines. I waited a few hours before using my dishwasher to allow the paint to dry and allow the tips to stick to the tines.
Read more
More
$26.95
- Compare At:
-
$32.07
- You Save:
-
$5.12
Genuine Whirlpool part
By: Whirlpool
Part Number: WP3369769
Dishwasher door panel insert. Reversible: white color on one side, black on the other.
Do-It-Yourself Stories from Customers like You
Rusted out front panels but dishwasher still working perfectly so kind of a waste to buy a new dishwasher Dennis Y. • Torrance , CA • October 13, 2014
Bought new top and lower front panels, removed/replaced rusted out panels & now dishwasher looks good as new! Only $34 from Appliance Parts Pros. Better than spending $500 on a new dishwasher.
Read more
More
$34.95
- Compare At:
-
$41.59
- You Save:
-
$6.64
Genuine Whirlpool part
By: Whirlpool
Part Number: 72032
Bottle with brush. Color: Black. Size: 0.6 fl.oz.
Do-It-Yourself Stories from Customers like You
Leaking diaphragm Herbert S. • Monroe Township , NJ • January 03, 2015
Replaced It With New One
Read more
More
$17.76
- Compare At:
-
$21.13
- You Save:
-
$3.37
Genuine Whirlpool part
By: Whirlpool
Part Number: WP3376397
Included with nut.
Do-It-Yourself Stories from Customers like You
Inadequate cleaning of dishes / detergent residue all over the interior Randy N. • Elkhart , IN • September 19, 2015
I cleaned all the jet nozzles with a toothpick and a pipe cleaner to remove the hard water deposits. I then replace the ring bearing under the bottom spray wand and the ring bearing under the upper spray wand. I also replaced the smaller radial ring bearing. Although none of them looked overly worn, it doesn't take much to cause the spray wands to spray inadequately.
Then, I replaced the float and washer assembly. Although it appeared to work properly when I lifted up on it and let it down, it...
Read more
More
$65.64
- Compare At:
-
$78.11
- You Save:
-
$12.47
Genuine Whirlpool part
By: Whirlpool
Part Number: WP489069
Size: 1/4 inch hex head, 10-12 x 1/2 inch.
Do-It-Yourself Stories from Customers like You
Broken handle foot pedal and missing parts Donald M. • Lake Arrowhead , CA • April 05, 2015
This trash compactor is in our vacation home. We never use it and now we are selling the house. When I looked to replace it I was amazed at how expensive a new compactor would cost. I found the serial number on the current compact entered it and your web site came up. Your schematics were excellent and made the repair very easy!
Read more
More
$5.95
- Compare At:
-
$7.02
- You Save:
-
$1.07
Genuine Whirlpool part
By: Whirlpool
Part Number: WP3374343
This dishwasher door spring restores proper counterbalance so the door opens smoothly and doesn't drop. The premium version provides the factory-specified tension used on select models for consistent, controlled door movement.
- Counterbalances the door for smooth opening and closing
- Helps prevent the door from slamming open or feeling heavy
- Supports stable, mid-position hold when springs are intact and matched
- Common signs of failure: door drops quickly, is hard to lift, or won't stay in position
What's included: 1 door spring Installation notes:
- Disconnect power and water; remove the toe kick/access panel to reach the springs
- Note which frame/hinge holes the old spring used and install the new spring in the same positions to match tension
- Use pliers to relieve tension safely; if your model uses two springs, replace both for balanced operation
- Wear gloves and eye protection; keep hands clear of moving hinges
Do-It-Yourself Stories from Customers like You
The dishwasher door spring broke. Rachael T. • Junction City , OR • November 07, 2022
I ordered the parts, deciding that if one spring had broken, the other one should probably be replaced at the same time. I followed the suggestion of ordering the door spring bearing given on the ordering page, and since I had not yet pulled out the dishwasher, did not know that it was not used in this older model. However, the order arrived quickly (4 days), and they are genuine Whirlpool, made in the USA, parts. The access to the sides of the dishwasher where the springs are attached...
Read more
More
$21.95
- Compare At:
-
$26.34
- You Save:
-
$4.39
Genuine Whirlpool part
By: Whirlpool
Part Number: WP302710
This inlet base seal is a gasket that fits between the inlet base and its mating surface. Replacing a worn seal helps maintain proper airflow through the inlet path and keeps spills and debris out of internal components.
- Forms a tight, continuous seal at the inlet base-to-housing joint
- Helps preserve correct airflow through the inlet path
- Blocks liquids, grease, and crumbs from leaking into the appliance interior
- Replace if the seal is cracked, flattened, brittle, loose, or you see visible gaps
What's included: One inlet base seal.
- Disconnect power to the appliance before servicing
- Remove grates/cartridges, filters, or trim as needed to access the inlet base
- Clean and dry mating surfaces; install the new seal in the same orientation without stretching or twisting
- Reassemble and verify the seal sits evenly with no gaps
Do-It-Yourself Stories from Customers like You
Leaks from around the door and from the pump motor Samuel M. • Sudbury , MA • January 12, 2016
1. To fix the leaks from around the door, I replaced the upper and lower door seals. These were purchased in a separate transcation, so they are not the parts shown here. The upper door seal worked as intended, but the lower seal would not stay in place on the lower edge of the door during a wash. Therefore I cleaned the grease and detergent off the old seal, and installed using silicone sealer/adhesive. The plastic edge pieces for the lower seal were supplied with the kit, and they installed...
Read more
More
$6.63
- Compare At:
-
$7.89
- You Save:
-
$1.26
Genuine Whirlpool part
By: Whirlpool
Part Number: WP3379673
This felt door vent seal fits around the dishwasher's door vent to help contain steam and moisture within the inner door. Replacing a worn seal helps prevent minor leaks and condensation around the vent area during cycles.
- Creates a gasket between the vent assembly and inner door panel to keep steam directed through the intended vent path
- Reduces moisture escape that can cause drips or water spots on the outer door or nearby countertop
- Helps limit condensation or musty odors from trapped moisture inside the door panel
- Indicators of failure include visible wear or separation of the felt and moisture around the vent during operation
What's included: 1 felt door vent seal Install notes:
- Disconnect power and turn off water supply before servicing the dishwasher
- Remove the inner door panel to access the vent assembly
- Note the seal's orientation; clean mating surfaces; seat the new felt evenly around the vent with no gaps
- Reassemble and run a short test cycle to check for leaks at the vent area
Do-It-Yourself Stories from Customers like You
Water leak from the right side of the dishwasher door Delbert T. • Bloomfield , IA • August 28, 2015
Replaced the felt seal and door vent assembly by removing the inside panel of the door and cleaning off the old seal and replacing with the new one. The vent assembly simply snapped out and was easy to replace with the new one. No more leaks and Mother was happy. Removal of the screws required a torx screw driver and someone to hold the door open while the panel was replaced. Easy fix.
Read more
More
$7.63
- Compare At:
-
$9.08
- You Save:
-
$1.45
Genuine Whirlpool part
By: Whirlpool
Part Number: WPW10082896
Includes washers.
Do-It-Yourself Stories from Customers like You
Whirlpool dishwasher no drying cycle heat John W. • Crestwood , KY • April 02, 2017
Replacement heater element installed exactly as described in the AppliancePartsPros video.
Read more
More
$75.64
- Compare At:
-
$89.26
- You Save:
-
$13.62
Genuine Whirlpool part
By: Whirlpool
Part Number: WP3369000
This upper draw bar is a door-latch linkage piece used in dishwashers. It connects the handle/actuator to the latch mechanism so the door closes securely and the door switch engages, allowing the cycle to start reliably.
- Links the door handle/actuator to the latch for positive closure
- Helps ensure the door switch is engaged so the unit will run
- Restores proper latch alignment and handle feel
- Common symptoms: door won't latch or pops open, dishwasher won't start, must push/hold door to run, loose or floppy handle
What's included: 1 upper draw bar Installation notes:
- Disconnect power at the breaker; turn off water supply if working near the inlet
- Open the door and remove inner-door screws to access the latch linkage
- Note bar orientation; transfer any clips/bushings and reuse existing hardware
- Reassemble and check latch engagement before running a cycle
Do-It-Yourself Stories from Customers like You
Latch would not open consistently on detergent dispenser James G. • Waxhaw , NC • January 12, 2015
Appeared to be two problems: the latch was worn and one of the pins that slid in a guide on the actuator located in the inner panel had broke off. Detergent lid spring and pin appeared to be OK but decided to replace since I was aready working on it. I ordered all the inner panel mechanism from the control arm to the latch actuator on the inner panel. The repair was successful as the detergent dispenser now opens during its cycle.
Read more
More
Genuine Whirlpool part
By: Whirlpool
Part Number: WP3374077
Size: 7 foot long.
Do-It-Yourself Stories from Customers like You
Bought a used dishwasher in excellent shape that needed the drain pieces to get it going Johnny R. • San Antonio , TX • April 14, 2015
Bought the parts and connected same...a breeze in finding and receiving and eventually installing these parts.
Read more
More
$62.78
- Compare At:
-
$74.71
- You Save:
-
$11.93