Kenmore Range 665.75849000 (66575849000, 665 75849000) Parts
Genuine Whirlpool part
By: Whirlpool
Part Number: 8184858
Trim kit frames your range oven door for a finished look. Replaces broken, cracked, or missing trim pieces damaged from regular use or heat exposure.
Do-It-Yourself Stories from Customers like You
Broken trim piece on door which caused outer door to fall off Patricia B. • Lake Ronkonkoma , NY • April 20, 2016
Kit arrived promptly. it took help of a friend and 45 minutes to install
Read more
More
$80.62
- Compare At:
-
$95.94
- You Save:
-
$15.32
Genuine Whirlpool part
By: Whirlpool
Part Number: WP3196164
The Screw is an OEM part for Whirlpool appliances that is responsible for securing various parts in place. The screw ensures a tight and secure fit, preventing any loose parts. A bad screw can occur due to wear and tear or accidental damage. If the screw becomes stripped, rusted, or lost, it can lead to instability or even malfunction of the affected parts.
Symptoms of a bad screw include:
- Loose or wobbly parts.
- Components not securely fastened.
- Difficulty in assembling or disassembling the appliance.
- Rattling or unusual noises during operation.
This OEM Whirlpool part can also be used on Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore/Sears brand appliances.
Do-It-Yourself Stories from Customers like You
Replaced broken oven door handle Peter R. • Baltimore , MD • January 25, 2015
Overall the fix wasn't too hard. The challenge was putting the oven door back together and holding it together while trying to tighten the screws. Enlisted my wife's help to hold the door and at first the handle screws wouldn't tighten. My cordless screwdriver's battery was under-charged. Once I switched batteries I was able to tighten the screws. Seemed like I needed to push too hard (my wife freaked "not so hard you will strip them!") however pushing hard was what was needed. Both screws...
Read more
More
$7.48
- Compare At:
-
$8.83
- You Save:
-
$1.35
Genuine Whirlpool part
By: Whirlpool
Part Number: WP8054129
The Spark Igniter is an OEM replacement part for Whirlpool gas ranges. Located inside the oven cavity it initiates combustion using high-voltage electricity. This is a broil igniter for the upper (broil) burner.
Causes of malfunction relate primarily to element degradation from extended heating cycles. Exposure to grease or other residue accumulation shortens the service life by insulating the hot surface.
Symptoms involve:
- Inability to ignite gas burners using the automatic igniter
- Safety issues arise requiring manual lighting with matches or lighters
- Difficulties baking or broiling without consistent flame generation
- Element replacement prevents further problems and safety hazards
This is a genuine Whirlpool OEM replacement this part is also compatible with Maytag, Jenn-Air and some Kenmore models.
This part fixes the following symptoms
-
Little to no heat when broiling
-
Gas igniter glows, but will not light
See more...
Do-It-Yourself Stories from Customers like You
The oven would light for a few seconds then turn off and at times would not light at all. Agnessa K. • Antelope , CA • March 14, 2014
Called a repairman and he told us we needed to change a bunch of parts and would cost over $400! Decided to do some research online and found suggestions to replace the spark igniter. Decided to give it a try. Took about 10min to replace and oven is now working perfectly, for a total of $30!
Read more
More
$89.95
- Compare At:
-
$107.04
- You Save:
-
$17.09
Genuine Whirlpool part
By: Whirlpool
Part Number: WPW10058460
Adjustable leveling leg installs on the front or rear corners of your range. Replace if broken, cracked, or worn to stabilize and level your appliance.
Do-It-Yourself Stories from Customers like You
Anti tilt bracket for stovetop oven Richard O. • Levittown , PA • October 11, 2019
Installed it according to video watched.
Read more
More
$9.63
- Compare At:
-
$11.56
- You Save:
-
$1.93
Genuine Whirlpool part
By: Whirlpool
Part Number: WP3400882
This machine screw is used across appliances to secure brackets, covers, and internal components. Replacing a missing or stripped fastener helps keep parts aligned and tight, reducing vibration and preventing loose or shifting assemblies.
- Provides machine-thread fastening for panels, brackets, and internal parts
- Helps eliminate rattling, vibration, and loose fits
- Restores proper attachment when the original screw is stripped, missing, or corroded
- Used wherever an 8-32 screw is specified in the service manual or parts list
What's included: One screw
- Disconnect power to the appliance; turn off gas/water if applicable
- Match the screw to the original location to confirm size and thread
- Start threads by hand to avoid cross-threading; use the correct driver
- Tighten snugly—do not overtighten to prevent stripping or cracking
Do-It-Yourself Stories from Customers like You
I had to change the burner switch Paul C. • Rochester , NY • November 09, 2014
Using the video on your site I was able to make the repair. It was a pretty straight forward repair. Thanks for having the diagram on your site for helping me find the right part.
Read more
More
$7.48
- Compare At:
-
$8.90
- You Save:
-
$1.42
Genuine Whirlpool part
By: Whirlpool
Part Number: WP3195097
This panel forms the floor of the oven, sitting above the bake element or burner to shield it from spills and provide a smooth, stable surface. Replace a warped or damaged panel to help maintain proper heating and easier cleanup. What it does:
- Forms the oven floor above the bake element or burner
- Shields the heat source from drips and debris to help prevent scorching and odors
- Supports designed airflow and heat distribution in the cavity
- Common replacement signs: warped or dented panel, rust or chipped finish, smoke/odors from spills beneath the panel, or uneven baking results
What's included:
Install notes:
- Disconnect power (and shut off gas supply for gas ranges) before servicing; allow the oven to cool completely
- Remove oven racks; release front fasteners or clips and lift the old panel out of the rear tabs (method varies by model)
- Seat the new panel into rear tabs, align the front edge, and secure as originally installed
- Verify the panel sits flat and clear of the bake element or burner before reassembling
Do-It-Yourself Stories from Customers like You
Oven burner occasionally failed to light usually in the middle of roasting a turkey or chicken oven then "locked down " Ulrich O. • Millburn , NJ • January 05, 2015
The problem is a finicky ignition system, Direct Spark Ignition. Apparently Whirlpool redesigned the igniter/burner assembly slightly to make it more reliable. The repair is very easy. Turn off power, but you don't need to turn off gas. Remove oven bottom and flame spreader, then remove burner/igniter assembly, one screw at front, one at back. Lift out burner assembly carefully to avoid stretching wire. Pull electric connector from pin on burner/igniter assembly. Vacuum to clean oven. ...
Read more
More
$103.31
- Compare At:
-
$122.94
- You Save:
-
$19.63
Genuine Whirlpool part
By: Whirlpool
Part Number: 8190618
Oven won't ignite or clicks but doesn't light? This bake burner with spark igniter fixes grounding issues and ignition failures. Easy DIY repair.
Do-It-Yourself Stories from Customers like You
Oven shuts off in the middle of baking Steven S. • Wenonah , NJ • May 11, 2015
Replaced igniter under oven floor panel.
Read more
More
$151.95
- Compare At:
-
$180.82
- You Save:
-
$28.87
Genuine Whirlpool part
By: Whirlpool
Part Number: WPY706189
Self-tapping screw used in range assembly. Features 8-18 thread size and 0.375 inch length. Also used in some washer models as cross-appliance hardware.
Do-It-Yourself Stories from Customers like You
Drum baffle broke off James H. • Etna , OH • March 21, 2017
I replaced all three baffles since the new one was a different design than then old one. i watched the video and the repair went well, except for hitting my hand with a hammer while removing the old baffles. went just like the video said it would
Read more
More
$7.48
- Compare At:
-
$8.90
- You Save:
-
$1.42
Genuine Whirlpool part
By: Whirlpool
Part Number: WP3196175
Size: 8-18 x 1/2 inch.
Do-It-Yourself Stories from Customers like You
Oven drawer wouldn’t slide properly. Nick B. • Hanover , MD • November 09, 2020
Whenever the drawer was opened, it would fall of the guide rails. This lead to the drawer being crooked several times. I took the drawer out and noticed one of the glides was missing. Ordered a new pair, popped it on and now the drawer slides properly.
Read more
More
$5.95
- Compare At:
-
$7.14
- You Save:
-
$1.19
Genuine Whirlpool part
By: Whirlpool
Part Number: WP3400832
Mounting screw for securing trim, hinges, drawer guides, and interior components. Replace if missing, stripped, or broken during repair or maintenance.
Do-It-Yourself Stories from Customers like You
The right front drawer support/guide was broken off Kenneth P. • Albany , OR • March 10, 2019
The replacement part was identical, arrived quickly as promised, and took only a couple of minutes to install. Excellent service. Very happy with the end result and the whole process.
Read more
More
$5.95
- Compare At:
-
$7.08
- You Save:
-
$1.13
Genuine Whirlpool part
By: Whirlpool
Part Number: WP179051
Replacement 10-32 machine screw for securing panels, brackets, and internal components. Ideal for replacing missing, stripped, or damaged hardware.
Do-It-Yourself Stories from Customers like You
Bake element broken on jenn air model s125 downdraft slide in range Patricia D. • Raleigh , NC • May 02, 2015
Ordered Bake Element, Y04100019 (Whirlpool AP4283614) to replace a broken bake element on my 30-year old Jenn-Air Model S125 Downdraft Slide-in electric range. Received the element very quickly but it had been damaged in shipping. Called AppliancePartsPros to report this and they quickly shipped another element - very easy process.
To install the element, I turned off the power to the range, put on rubber gloves (just in case) and removed the two sheet metal crews at the rear of the oven -...
Read more
More
$7.48
- Compare At:
-
$8.90
- You Save:
-
$1.42
Genuine Whirlpool part
By: Whirlpool
Part Number: WPW10293048
Range oven won't ignite or heat? Gas valve controls gas flow to burners. Common fix when igniter sparks but no flame appears. 10-15 minute repair.
Do-It-Yourself Stories from Customers like You
Everything worked on stove except oven Felix G. • Beach Park , IL • March 07, 2016
I know absolutely nothing about fixing appliances, nothing. So I googled and found this site and narrowed it down to 1 of three parts (totaling about $550). I tried the first two and with no luck I almost gave up thinking I didn't know what I was doing and better off buying a new stove. For the last part I had to dissemble more and thought I was getting over my head, guess what? The oven worked!!! The part I needed was only $150 and saved money on labor and who knows what what else. Just to...
Read more
More
$316.95
- Compare At:
-
$377.17
- You Save:
-
$60.22
Genuine Whirlpool part
By: Whirlpool
Part Number: WP8053834
Replace cracked, shattered, or broken outer glass on your range oven door. This front glass panel installs between the door frame and trim pieces.
Do-It-Yourself Stories from Customers like You
Broken oven door glass and trim Heidi A. • Topeka , KS • December 05, 2014
Replaced glass and trim
Read more
More
$153.66
- Compare At:
-
$181.32
- You Save:
-
$27.66
Genuine Whirlpool part
By: Whirlpool
Part Number: W11233072
This factory screw secures appliance components to their mounting points. Replace missing, worn, or stripped hardware to restore a tight fit, proper alignment, and quieter operation across the affected assembly.
- Fastens panels, brackets, covers, or internal parts to the chassis or frame
- Helps maintain alignment and support, reducing rattle, vibration, or looseness
- Replaces missing or damaged screws that have backed out, broken, or stripped
- Restores secure mounting after service when original hardware is lost
What's included: 1 screw Install notes:
- Disconnect power; shut off water or gas supplies before servicing
- Use the correct driver; start threads by hand to avoid cross-threading
- Match length and thread to the original location; do not substitute with longer hardware
- Tighten snugly; do not overtighten into plastic or thin metal
Do-It-Yourself Stories from Customers like You
Bake element broken on jenn air model s125 downdraft slide in range Patricia D. • Raleigh , NC • May 02, 2015
Ordered Bake Element, Y04100019 (Whirlpool AP4283614) to replace a broken bake element on my 30-year old Jenn-Air Model S125 Downdraft Slide-in electric range. Received the element very quickly but it had been damaged in shipping. Called AppliancePartsPros to report this and they quickly shipped another element - very easy process.
To install the element, I turned off the power to the range, put on rubber gloves (just in case) and removed the two sheet metal crews at the rear of the oven -...
Read more
More
$21.46
- Compare At:
-
$25.54
- You Save:
-
$4.08
Genuine Whirlpool part
By: Whirlpool
Part Number: WP3196068
Broken indicator light lens? This red lens covers the control panel light opening, restoring visibility and protection. Easy DIY fix in under an hour.
Do-It-Yourself Stories from Customers like You
The instrument panel was deteriorated from someone using the wrong products Richard M. • Glen Burnie , MD • July 23, 2019
Replaced the panel with a new one, and put the new indicator lights on.
Read more
More
$8.56
- Compare At:
-
$10.10
- You Save:
-
$1.54
Genuine Whirlpool part
By: Whirlpool
Part Number: WP8053807
Replaces broken or worn oven door hinges on ranges. Installs inside the door frame to support proper opening and closing. Sold individually.
Do-It-Yourself Stories from Customers like You
The oven door would not close completely William R. • Emporia , KS • July 27, 2016
This oven was a Kenmore model #66595822003. I replaced both spring hinges. This oven was a white oven so it took the MFG# WP8053807 hinge (order two of them). They are the same hinge. No left or right. To get the door off the oven, open the door all the way open, I installed pins (preferably only 1/4" long) in the holes of both hinges. Then remove the spring steel retainers above old hinges in the oven frame. These holds hinges in place. Now close the door until hinge stops on pins. Lift up...
Read more
More
$77.76
- Compare At:
-
$91.76
- You Save:
-
$14.00