Kenmore Range 790.78694400 (79078694400, 790 78694400) Parts

• Gas smell
• Gas igniter glows, but will not light
• Little to no heat when baking
• Won't start

My Tappan Range, which I paid a grand total of $65.00 for, and have been using since Katrina, (Katrina in 2005 is how we measure time in South Mississippi.) I live in an old house, and I am old, too. Last winter was the coldest I can remember, and my husband (older than I and far more hard-headed) used the oven like a heater. I read all user's manuals, because I use only used stuff, I can download the manuals or read them online, and it clearly stated in there NOT to use the oven as a... Read more

Before we replaced the board, my wife tried to replace just the element. We had one we had ordered several years ago when this same thing happened. When that didn't work we replaced the board and could see where the old board was damaged so we figured this was the solution. It would have been except the bottom element my wife used to replace the old element (which was fine but had been thrown out figuring the new one was new so why keep the old one) was 1" shorter in the back than the old... Read more

I have used this site before to fix my dishwasher, so I knew to check here first. I searched other's comments to troubleshoot my problem. Ordered the part and it arrived in only a couple of days. I should insert here that I am a 45 yo female, so if I could do this, anyone can. I watched the video and proceeded to replace the part. For my particular model, I didn't access the part from the back, but instead through the underside by removing the bottom drawer. Total from start to finish... Read more

• Oven is too hot
• Little to no heat when baking
• Won't start
• Oven not heating evenly

I replaced the probe which is a thermocouple. Naturally the connector was different from the one on the stove so I cut off the connector on the old probe and soldered it to the new probe. The cleaning of the wires and soldering them was the most time consuming activity of the repair. My wife just tried the stove and the oven temperature read exactly as the setting. Read more

We ordered a igniter and a new regulator. My husband installed the parts it works great now. Read more

• Won't start

Replaced igniter and orifice assembly, and replaced spark module. Used the video for help, but the video doesn't show the top cover piece that needs to be taken off first. Also the screws for the igniter set were stuck from old grease or something and had to be drilled out. Overall the project was well worth my time for the cost vs replacement decision. AppliancePartsPros.com makes it so easy to choose a part and guesstimate the probably of choosing the right one. Read more

The repair was a success. The switch and came looked different from the original. I called Appliance Parts Pro, they lady on the phone said that Frigidaire changed the switch and how to wire it up correctly. Problem solved. It all works as it should. Read more

It took a little longer then I was hoping but wasn’t terrible. If the burner is very old at all make sure to get the new screws. Both of mine snapped when trying to remove them. The new one works great. Read more

Had to pull double oven and range top out from wall which involved removing the upper kitchen cabinet. Took the sheet metal off the back and had the socket swapped out in a couple of minutes. My old oven works like a charm! Read more

Bought new burner tops for all four burners. Lights great now with nice blue flames and no yellow. Read more

Watched repair video's to learn where parts were located. Put replacement in and it worked great! Read more

I ordered one of these and used two extra screws I had lying around and now I have a nice level stove! Thanks AppliancePartsPros.com! Read more

Easy just pull clip and put back Read more

It took a little longer then I was hoping but wasn’t terrible. If the burner is very old at all make sure to get the new screws. Both of mine snapped when trying to remove them. The new one works great. Read more

Installed the new bracket as per instructions with template enclosed and it was perfect. Read more

I replaced the switch/wire harness that connects to the gas valves. Read more