Kenmore Range 790.92302010 (79092302010, 790 92302010) Parts

The Oven Light Socket is an OEM replacement part for Frigidaire electric ranges and wall ovens. It houses the bulb that illuminates the interior of the oven cavity.

Causes of a bad light socket can include a loose or broken connection due to regular use, scorched or burnt terminals from overheating, or damage from moisture.

Symptoms of a bad light socket include:

• The oven light not turning on when activated  
• Flickering or intermittent bulb operation
• Signs of corrosion or oxidation around the bulb base
• Excessive heat emission from the light area

This OEM Frigidaire replacement part is also compatible with ranges and wall ovens from Electrolux, Gibson, and Kelvinator. 

This broil heating element mounts at the top of the oven cavity to provide intense, direct heat for broiling and to assist with preheating. Replacing a failed element restores even broiling performance and helps the oven reach temperature properly.

• Provides high, top-down heat for broiling
• Common failure symptoms: no broil heat, uneven browning, trips breaker when broil is selected, visible hot spots or breaks in the element
• Helps with overall oven preheat and temperature recovery

• Disconnect power before service; the element is high-voltage
• Remove oven racks to access mounting screws
• Support wiring when transferring leads to the new element to prevent panel damage
• Avoid touching new element with bare hands; clean any oils from terminals

The Oven Seal is an OEM replacement part for Frigidaire ovens. This seal is installed around the oven door to create a tight barrier, preventing heat from escaping during operation. By maintaining the internal temperature, the seal ensures efficient cooking and baking while reducing energy consumption.

Over time, the oven seal can wear out or become damaged due to exposure to high temperatures, frequent use, or accidental mishandling. A compromised seal can lead to heat loss, uneven cooking, or longer preheating times.

Symptoms of a bad oven seal include:

• Heat escaping from the oven door
• Longer cooking times or unevenly cooked food
• The oven taking longer to preheat
• Visible cracks, tears, or flattening of the seal

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

The Control Board Overlay is an OEM part for Frigidaire ranges. This part provides the buttons and display that control the range's functions. The overlay covers and protects the control board, ensuring that the buttons and display remain intact and operational.

Causes of a bad control board overlay can include wear and tear from regular use, exposure to heat and moisture, or damage from accidental impacts. 

Symptoms of a bad control board overlay include:

• Buttons that are unresponsive or hard to press
• Fading or peeling of the overlay graphics
• Inaccurate or malfunctioning display
• Visible damage or cracks on the overlay

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

The Leveling Leg Assembly is an OEM part for Frigidaire ranges. This part provides stability by allowing users to adjust the height of the range, ensuring it is level and balanced on the floor.  

Causes of a bad leveling leg assembly can include wear from frequent adjustments, damage due to heavy loads, or breakage from accidental impacts.  

Symptoms of a bad leveling leg assembly include:

• The range being uneven or wobbling
• Difficulty in leveling the range using the legs
• Noise or movement when the range is in use
• Doors not aligning properly

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

The Switch Rocker is an OEM part for Frigidaire ranges. This switch is used to control various functions of the range, such as turning on heating elements or activating specific cooking modes. It provides a reliable and straightforward interface for managing the range's features.

You should replace the range switch rocker if it becomes faulty. Causes of a bad switch rocker can include wear and tear from frequent use, exposure to high temperatures, electrical malfunctions, or physical damage from impacts or mishandling. A defective switch rocker can result in unresponsive controls, making it challenging to operate the range effectively.

Symptoms of a bad Range Switch Rocker include:

• The switch not responding when pressed
• Inconsistent or flickering performance of the heating elements
• Physical damage or looseness in the switch
• Intermittent operation or complete failure to activate the desired function

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

The Vent Trim is an OEM part for Frigidaire ranges. This part frames and supports the oven's ventilation system, ensuring proper heat dispersal and maintaining the aesthetic integration of the range within the kitchen setup.  

Common causes for vent trim issues include physical impacts during cleaning or use, thermal deformation from continuous exposure to high temperatures, and general wear and tear over time.  

Symptoms of failing Vent Trim include:

• Loose or ill-fitting trim that may not stay in place
• Visible damage such as cracks or warping due to heat exposure
• Increased heat retention or abnormal heat outside the oven
• Aesthetic discrepancies that impact the overall look of the kitchen

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

The Anti-Tip Bracket Kit is an OEM part for Frigidaire ranges and ovens. This part secures the appliance to the floor or wall, preventing it from tipping over when the oven door is opened or when heavy cookware is placed on an open door or extended rack. The kit typically includes a metal bracket, screws, and installation instructions.

Over time, or during instances of moving or remodeling, the anti-tip bracket may become dislodged or may not be reinstalled correctly, which can compromise the safety of the appliance. 

Symptoms of a missing or improperly installed Anti-Tip Bracket include:

• The range or oven tilts forward when pressure is applied to an open door
• The appliance moves more easily than expected when nudged or cleaned
• Visible absence of a bracket at the lower back portion or floor area behind the appliance

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

This Door Trim Kit restores the finished look and proper fit around the door. It replaces damaged or missing trim that frames the door/panel, helping secure outer components and refresh the appliance's appearance.

• Provides a clean, finished edge around the door perimeter
• Helps retain/position the outer glass or panel on applicable designs
• Replaces cracked, warped, loose, or missing trim that may rattle or leave gaps
• Common symptoms: visible damage, looseness, gaps, or cosmetic wear around the door

• Disconnect power at the breaker or unplug the appliance before servicing
• Protect the work surface; wear cut-resistant gloves and handle glass carefully
• Note orientation and fastener locations; transfer any reusable clips/screws from the original assembly
• After reassembly, confirm smooth door operation and proper alignment/seal

The Screw is an OEM replacement part for Frigidaire appliances. This screw is used to securely fasten components, such as panels, brackets, or internal parts, ensuring the appliance remains stable and functions correctly. Its precise design ensures a snug fit and reliable performance in the designated area of the appliance.

Over time, screws can become stripped, corroded, or loosened due to vibrations, frequent use, or environmental factors. A damaged or missing screw may lead to instability, misaligned components, or operational issues with the appliance.

Symptoms of a bad or missing screw include:

• Loose or misaligned panels or components
• Rattling or unusual noises during operation
• Difficulty in securing parts during repairs or adjustments
• Parts becoming detached or unstable

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

This truss-head machine screw secures a switch to its mounting bracket or panel. Replacing a worn or missing screw restores a solid, aligned switch fit for reliable operation.

• Fastens the switch body to a bracket or chassis panel
• Helps keep the switch aligned for consistent actuation
• Replaces stripped, corroded, or missing mounting hardware
• Common symptoms: loose or wobbly switch, misalignment, rattling or vibration around the switch area

• Disconnect power to the appliance before servicing
• Start threads by hand to avoid cross-threading; tighten snugly without overtightening
• Verify thread size and length match the original hardware
• If multiple screws secure the switch, replace them in a consistent pattern to maintain alignment

This replacement handle restores a secure, comfortable grip for opening and closing your appliance door. It replaces a cracked, loose, or missing handle so operation feels normal again and the appliance maintains a clean, finished look.

• Provides a sturdy handhold to pull/push the door during everyday use
• Attaches to existing mounting points on the door
• Common symptoms: cracked or broken handle, looseness, missing handle, difficulty opening the door
• Helps return the appliance's appearance to like-new condition

• Disconnect power to the appliance before starting; allow hot surfaces to cool
• Wear cut-resistant gloves; support the door/handle while removing hardware
• Reuse existing screws/end caps as applicable; start all fasteners before tightening
• Tighten evenly without overtightening; verify smooth door operation after installation

The Screw is an OEM part for Frigidaire ranges and ovens. This part is designed to securely fasten various parts of the appliance, ensuring stability and durability. 

Over time, screws can become loose due to the expansion and contraction of materials with temperature changes. Regular use and the occasional necessary removal for repairs or cleaning can also wear down the threads, making them less effective.  

Symptoms of a bad Screw (Chrome) include:

• Loose or wobbly components that should be securely fastened.
• Difficulty in securing parts due to stripped or damaged screw threads.
• Visible corrosion or deterioration of the screw.

This OEM Frigidaire part can also be used on Electrolux, Frigidaire, Gibson, Kelvinator, Westinghouse, and Sears/Kenmore.

Size: 8-18 x 0.5 inch. Color: Chrome.

This control-panel switch restores reliable on/off control of a selected function on your range or wall oven. Replacing a worn or intermittent switch helps ensure the appliance responds consistently when you toggle that function.

• Directs power to the associated circuit when switched on or off
• Common symptoms: function won't turn on/off, intermittent operation, or the switch feels loose/sticks
• Helps restore positive, consistent control from the backguard/control panel

• Disconnect power at the breaker before servicing
• Access the switch from the control panel/backguard; retain screws/clips
• Label/photograph wire positions and transfer leads one at a time to the new switch
• Ensure firm terminal connections, reassemble, restore power, and test operation

Replacement glass panel that restores visibility and helps protect internal components for compatible Frigidaire appliances. Use this glass to replace cracked, chipped, or shattered panels and return your appliance to safe, usable condition. What it does:

• Replaces broken or damaged glass panels used on the appliance door, shelf, or panel area.
• Stops loose shards and visible cracks that can cause safety concerns or interfere with normal use.
• Restores clear visibility through the door or panel.
• Helps prevent further damage to internal components by replacing compromised glass.

• Disconnect power and unplug the appliance before beginning any repair.
• Handle with care and wear cut-resistant gloves and eye protection; glass edges may be sharp.
• May require partial disassembly for removal and installation—follow OEM instructions.

This factory screw secures panels, brackets, and other components in your cooking appliance. Replace a missing, stripped, or corroded fastener to restore a tight, rattle-free fit and keep parts properly aligned during use.

• Fastens components to maintain proper alignment and stability
• Helps prevent vibration, rattling, and loose parts during operation
• Replace if threads are stripped, the head is damaged, or the screw is missing
• Commonly used to mount internal or exterior parts in ranges and wall ovens

• Disconnect power and allow the appliance to cool; shut off gas supply if applicable
• Use the correct driver bit to avoid stripping the screw head
• Install in the original location and do not overtighten
• If the receiving threads are damaged, repair or replace the mating part before installation