Lg Dryer 91029 Parts

I consulted with the internet and your website and determined I had a bad roller wheel. I was going to buy just one but determined if you have to take the thing apart, just replace all of them. These lasted 10 years after all. Opened up You Tube for the method to take the dryer apart. After doing the washer last year, I felt pretty bold and just ripped into the project. Within 30 minutes I had the drum out and located the problem wheel ( rear right side). It was locked up due to hair build up... Read more

I replaced the warped cover guide and the lint filter. Now it works perfect! Sears was going to charge $100 just to diagnose the well known problem, not including parts and labor. It only requires 4 screws(i used the old ones). Easy fix. Read more

Checked and cleaned vent which was in need of cleaning, but not too bad (I do not consider this a primary causal detail, but can be a problem, so clean yours). Replaced Hi-Limit Thermostat (safety thermostat) after confirming the circuit was open with ohm meter. While I was in there, I completely cleaned the heater and ducting and internal workings of the dryer. Confirmed the heater coils were good via 20ohm, 20ohm, 40ohm readings (LG service manual has wrong readings). Two weeks later, same... Read more

Was going to order 4 new wheel & spindle sets, then saw you could get just the wheel for 1/3 the cost, so I ordered those. Then in the frequently ordered other items I saw the idler wheel assy. So I ordered one of those also. Glad I did, it was in worse shape than any of the wheels which still seemed to spin freely after I got all the hairs and crap off them. Anyways, went by the video step by step. Pretty straightforward. Have a good vacuum handy, I’m surprised that it used to dry at all... Read more

The original issue with the dryer is that a corner of the lint screen was sticking out of the lint screen guide, and it would not stay flush with the guide. As a result, many tank top straps, waistband strings, and blankets would get caught on this corner and twist, tear, or warp my clothes. When I did my research on the issue, I kept reading that it was an issue with the lint screen that came with the dryer. So I ordered the lint screen, guide, and cover that appliance part pros recommends to... Read more

Checked and cleaned vent which was in need of cleaning, but not too bad (I do not consider this a primary causal detail, but can be a problem, so clean yours). Replaced Hi-Limit Thermostat (safety thermostat) after confirming the circuit was open with ohm meter. While I was in there, I completely cleaned the heater and ducting and internal workings of the dryer. Confirmed the heater coils were good via 20ohm, 20ohm, 40ohm readings (LG service manual has wrong readings). Two weeks later, same... Read more

I first ordered a thermostat and ignitor and replaced and that did not work. I asked Appliance Parts Pros their opinion in the chat and they said it was the coils in the gas valve but you had to replace the entire valve as the coils are not sold individually. So i ordered the part and also replaced the thermistor and drum belt while i had the dryer apart anyway! And this fixed the problem! These guys are the absolute best and most helpful i have ever dealt with. This is the second time i... Read more

Ordered conversion kit from Appliance Parts Pros.com and installed it myself. Most difficult part of the repair, was the removal of the front casing of the dryer to access the location of venturi tube to be changed out. The instructions were helpful, but not specific enough for my dryer. Once the casing was off, the job was not too difficult - you will need a set of short screwdrivers to remove the burner flange and close the pressure adjustment screw, normal length screw drivers will come into... Read more

We called a repairman out who was rude, obnoxious and seemingly incompetent. After an hour of dissembling our dryer, he quickly slapped it back together and told us it would be $200 to fix. No other explanation. We sent him on his way and I found your site, found the ($5) part and watched the 5 min repair video. Ordered the part and had it in our hands in less than 48 hours. I had the dryer repaired in 20 min. Saved us a lot of money and made me feel pretty good about my own normally meager... Read more

The original issue with the dryer is that a corner of the lint screen was sticking out of the lint screen guide, and it would not stay flush with the guide. As a result, many tank top straps, waistband strings, and blankets would get caught on this corner and twist, tear, or warp my clothes. When I did my research on the issue, I kept reading that it was an issue with the lint screen that came with the dryer. So I ordered the lint screen, guide, and cover that appliance part pros recommends to... Read more

After unplugging the dryer from the wall socket, I used a screwdriver ( Phillips ) to remove the light cover fixture. This gave me access to the bulb which had burned out. I first use my fingers to remove the bulb but the base came lose from the glass bulb. I then used a needle nose pliers to remove the metal base of the bulb from the light fixture. Once the metal base was removed I used my fingers to replace the old bulb with a new one. It screws in easily. Now I replaced the light fixture... Read more

If your LG Front load washers sounds like a freight train, STOP USING IT. You're doing more damage and will need more parts to fix it. After the noise became unbearable, I began to explore and disassemble. I knew enough to know the bearings must be bad but had never done this repair before. ( I am however pretty mechanically inclined.) Watch this video before you start tearing your LG apart. APP did a great job explaining the steps of the repair. Do a search on this site or youtube.com with... Read more

Https://www.appliancefactoryparts.com/content/pdfs/125631-1.pdf has the details to disassemble the dryer to access the vent part that cost apx$28. 1.5 hrs and some patience along with a screw driver and players was alll it took to to remove the cover, control panel, front cover, drum, belt, gas line and manifold assembly, flame tube? And rear drum panel in order to replace worn part. Reassembled in 15minutes to clean and vacuumed dryer. Works great now. Read more

• Too hot
• Doesn't shut off
• Takes too long to dry

I replaced the dryer motor. I followed the repair video on the Appliance Parts Pro site, with a few modifications to the procedure. I loosened the control panel and flipped it forward to improve access to the wiring connectors. I also loosened the front panel and tipped it forward before disconnecting the door switch as there wasn't enough space to disconnect the switch otherwise. Removal of the blower assembly required the use of penetrating lubricant as the assembly was stuck on the motor... Read more

Chatted with 1 of your professionals and within a minute she had the part and it was on it's way. The job was VERY easy to fix and the part is working great! Read more

Watched appliance parts pros YouTube video of how to get access and how to replace the broken part. Read more