Lg Dishwasher D1607TB Parts

Secures and pivots the dishwasher door for smooth opening and proper alignment. Replace if your hinge is broken, cracked, or worn to restore stability.

Protective cover cap for dishwasher installation. Replaces cracked, broken, or missing caps. Ensures proper coverage and protection of components.

Base cover assembly for dishwashers. Installs at the bottom to protect internal components. Replace if cracked, damaged, or missing for proper coverage.

Seals dishwasher door to prevent leaks, contain heat and moisture. Replace if water escapes, steam leaks, or seal is cracked. Verify fit by model number.

The Upper Rack Assembly is an OEM part for LG dishwashers. This part provides a durable and efficient space for washing glasses, cups, and smaller dishes. This assembly maximizes the cleaning capacity of your dishwasher, allowing for the organized placement of items to ensure they are thoroughly cleaned and dried.  

Causes for issues with the upper rack assembly often involve prolonged exposure to water and detergent, leading to rust or corrosion, physical damage from loading or unloading, or wear and tear from regular use.

Symptoms of a malfunctioning Upper Rack Assembly include:

• Difficulty sliding the rack in or out
• Rust or corrosion that can lead to stains on dishes
• Broken or missing tines affecting the rack's ability to hold dishes securely

This OEM LG part is also compatible with some Kenmore models.

Dishwasher dishrack roller and axle assembly. Installs on upper or lower dish rack to allow smooth gliding. Replace if broken, cracked, or missing.

This dishwasher sensor assembly contains the thermistor that monitors wash-water temperature and sends readings to the control. Replacing a faulty sensor restores accurate heating and cycle timing for consistent cleaning and to prevent temperature-related interruptions. What it does:

• Measures wash-water temperature via an NTC thermistor
• Sends a resistance signal to the control to manage heater operation and cycle timing
• Helps maintain target temperatures for proper cleaning performance
• Common failure symptoms include no heat or overheating, long/short cycles, temperature-related errors, or poor cleaning/drying

• Disconnect power at the breaker and shut off water before servicing
• Access the sump area from the bottom; you may need to pull the dishwasher forward for clearance
• Expect some residual water—protect the area with towels
• Seat the sensor fully in the sump opening, reconnect the harness, and run a test cycle to check for leaks and proper heating

Seals the joint between sump and tub to prevent leaks. Replace if worn, cracked, or flattened to stop water escaping. Confirm fit with your model number.

Fixes dishwasher leaks and draining problems. This sump assembly collects and channels water to the drain pump. DIY repair typically takes 1-2 hours.

Mounts over the dishwasher's drying fan vent opening to shield the blower and direct airflow into the tub. Replace if cracked, damaged, or missing.

This replacement switch cam interfaces with a lever or knob to actuate a microswitch. It restores reliable on/off signaling and the positive feel/engagement of the related control or latch mechanism when the original cam wears or cracks.

• Translates lever or rotary motion into precise switch activation
• Ensures the switch travels fully to open and close as intended
• A worn or broken cam can cause intermittent operation or functions that won't start/stop as expected
• Helps bring back a defined "click" or detent at the control/lever

• Disconnect power to the appliance before servicing; turn off gas/water if applicable
• Access the switch or latch assembly; remove any knob, trim, or cover as needed
• Note the cam's orientation/indexing before removal; take photos for reference and transfer any springs/clips
• After reassembly, manually test the mechanism to ensure smooth switch actuation before restoring power

Fix dishwasher not draining or OE error codes with a new check valve. Prevents backflow and keeps water moving properly. Easy 30-minute DIY repair.

Connects internal water lines in your dishwasher. Replace if cracked, worn, or leaking to restore a secure seal and prevent water damage under the unit.

Creates a watertight seal to prevent leaks in your dishwasher. Replace when worn or cracked to stop water damage. Confirm fit with your model number.

Replace cracked or worn dishwasher leveling legs. This foot assembly installs at the base corners to restore proper height adjustment and stability.

This is a common fastening nut used to secure panels, trim, or components on compatible LG appliances. It provides a simple, reliable way to hold mating parts in place and restore proper fit and function. What it does

• Secures panels, brackets, or hardware to prevent movement or vibration
• Stops rattling or loose parts caused by a missing or worn nut
• Restores proper alignment when replacing damaged or stripped fasteners
• Works where a standard threaded nut is required for reassembly

• One common nut as pictured

• Disconnect power and water before servicing the appliance
• Use the properly sized wrench or socket to avoid rounding the nut
• Do not overtighten; tighten until snug and secure per OEM torque guidance
• Replace like-for-like—thread size and type match the original