Samsung Washer WF203ANWXAA Parts

With the video that was made from appliance pro.Help me out one hundred percent to understand what I was dealing with Read more

• Shakes and moves

My washing machine was making a loud thumping sound and bouncing around a bit. Research suggested that it could be bearings and/or the spider shaft assembly. After watching the instruction videos to replace the spider or bearings, I seen you need to replace both the shaft seal and tub gasket to get to the spider and bearings. So I ordered both and waited for them to arrive. Plan was to disassemble the washer, determine what was needed, order the additional parts needed, and reassemble after the... Read more

I followed Matt's awesome video from AppliancePartsPros.com to build up my "I can do this" reserves. But here's the story leading up to that point... We purchased our Samsung WF419 on a “Black Friday” special November 2009 expecting to get some good years out of the washer/dryer pair. We don’t run more than 2 or 3 loads a week in the washer, so ours has had relatively little use over the beginning of its anticipated and expected long life-cycle. When the “thumping” started on the spin cycle a... Read more

Replaced door lock switch. Read more

I followed Matt's awesome video from AppliancePartsPros.com to build up my "I can do this" reserves. But here's the story leading up to that point... We purchased our Samsung WF419 on a “Black Friday” special November 2009 expecting to get some good years out of the washer/dryer pair. We don’t run more than 2 or 3 loads a week in the washer, so ours has had relatively little use over the beginning of its anticipated and expected long life-cycle. When the “thumping” started on the spin cycle a... Read more

Normally, I hire someone to come fix washer or dryer problems as time is limited and if the cost is close or more than the machine, I buy a new one instead. But since we are on shelter-in-place, I figure I could repair it since I have more time on my hands and my brother assured me, it was not hard to do. I took the top panel, door off and then looked online to find a service manual, which allowed me to take the front panel off. My suspected drain hose was the failure mode: the rubber tube... Read more

• Won't start
• Lid or door will not open
• Lid or door won't close
• Will not agitate

The washing machine would allow you to program it, and all the lights on the control panel would light up, but pressing start did nothing. I tried putting the washer in diagnostic mode, but was unable to do so. The machine was not showing any fault code. I originally thought it was a problem with the 'Start' button and I thought that I'd buy a replacement part from the original seller of the washer. I was told by the 'live help chat person' that the problem was likely in the washer user... Read more

I found a youtube video about replacing the hot water valve in a Samsung washer. It looked pretty easy. I had been very satisfied with an earlier order from AppliancePartsPros.com, so I ordered this part on Sunday after 9PM, standard delivery, hoping to get the part by the end of the week. I was flabbergasted to receive the part TUESDAY MORNING! Wow! I followed the instructions in the youtube video exactly. It took around 15 minutes, because I was being very careful not to drop screws in... Read more

I took apart the washer to find both of the weight balancers had broken in 2 and were banging around. They had also caused the boot seal to rip. I removed the broken weight balancers and replaced them along with a new boot seal. There was one small spot with the seal wasn't fully attached to the outer drum so I had to take it back apart to fix that minor error on my part. Otherwise, it was a fairly easy fix. Read more

• Door latch failure

I removed the wire and rubber seal in order to get to the door lacth then I unscrewed the three screws popped out the latch put the screws and the rubber and wire back and tested the washer. The door now locks and I can wash again...YEPPPPY Read more

First indication something was wrong when the washing drum starting to violently bang against the inside of the washer while in spin cycle. Then, when I opened the washer door, a misty smoke came from the inside. With the video from Appliance Parts Pros, disassembly of the washer was no problem. First, I replaced the four shocks on the washer drum. But, after a test run, determined that it was spider arm assembly. Again, the series of instructions made getting to the part fairly easy. The... Read more

The error code implies a faulty fill valve. This was not the case for me. Replacing the main PCB assembly solved the problem. I have run two full loads since the repair with no problems. Read more

Ordered a new outer door seal and watched their video before replacing. Easy to follow the video and it took me less than 30 min to complete repair. A small amount of diluted dishwashing liquid on the new seal lip makes the install much easier. Read more

Needed to replace washer counter balance. Also order shock absorbers in case they needed to be replaced, fortunately they didn't need replacement and will be returned. I used Appliance Parts Pros many time and always found them to be very helpful and the repair videos are very helpful. Read more

I ordered new door gasket, front and rear clamp for gasket and installed them. Read more

I first check the schematics to find the heat sensor. On my model it's c on the control panel. I checked the continuity on the orange and white wires. It showed some continuity but not much. I then went to the heater element and found the orange and white wires going to the thermistor. Turns out the heater element and thermistor need repalced. Read more