Thermador Dishwasher DWHD44EF Parts

The Float is an OEM part for Bosch dishwashers. This float senses water levels inside the dishwasher, signaling the inlet valve to refill when needed.

Causes of a float malfunctioning can be mineral deposits accumulating and weighing it down over time, or cracks in the plastic housing allowing water in.

Symptoms of a bad float include:

• The dishwasher not filling or filling slowly
• Error codes related to fill issues
• Improper water levels impacting wash results

This genuine OEM Bosch part is also compatible with Thermador, Gaggenau and select Kenmore models.

Includes door latch, strike plate and microswitch.

Detergent not dispensing during wash cycle? This actuator arm with spring releases the detergent cup at the right time. Moderate DIY repair.

This replacement screw secures appliance panels and internal brackets so components stay tight and aligned during everyday use. Replacing missing or stripped hardware restores a solid fit and helps minimize vibration and rattling.

• Fastens covers, panels, and brackets to their mounting points
• Helps maintain alignment of the attached component
• Reduces movement that can cause noise or wear
• Typical reasons to replace: missing screw, stripped head/threads, loose panel or bracket

• Disconnect power and, if applicable, shut off water before servicing
• Use the driver bit specified for your model; hand start threads to avoid cross-threading
• Tighten snugly without over-torquing to prevent stripping
• Replace screws one at a time to maintain alignment

Single Torx T20 screw secures dishwasher panels, brackets, and trim. Replace missing, stripped, or damaged fasteners to keep components tight.

This is a trim strip that attaches along the lower portion of the dishwasher door. It helps seal the door edge and provides a finished appearance to the front panel. Replace this piece if it is cracked, warped, or missing, which can lead to water leaks around the bottom of the door during wash cycles.

Black adapter connects dishwasher drain hose to another hose or fitting for secure wastewater routing. Replace when cracked, loose, or missing for leak-free.

Traps food debris and particles in your dishwasher sump. Replace when clogged with hard water deposits or buildup affects cleaning. Verify fit by model.

Seals the NTC temperature sensor port in your dishwasher to prevent leaks and ensure accurate temperature readings. Replace if leaking or worn. Verify fit with your model number before ordering.

Circular sealing gasket creating watertight joints between dishwasher components. Replace when flattened or cracked to prevent leaks. Confirm fit by model.

Seals the aqua sensor assembly to prevent water leaks and protect electronics. Replace if you notice leaks or sensor errors. Confirm fit with your model.

Spring-style hose clamp secures water hoses to prevent leaks at connections. Replace if worn, rusted, or if you notice dripping around hose fittings.

Right side door hinge plate for dishwashers. Secures the door hinge mechanism to the frame. Replace if cracked, broken, or damaged to restore proper fit.

Left side door hinge plate for your dishwasher. Replaces cracked, broken, or worn hinge plates that cause door misalignment or instability.

Replacement water level control cover for dishwashers. Snaps over the water level control assembly. Order a new cover if yours is broken, cracked, or missing.

This holder is a molded mounting bracket that secures internal components and helps maintain proper alignment for reliable operation. It replaces a worn or broken support to restore fit and function. What it does:

• Secures and supports the associated component to prevent movement or misalignment
• Restores proper positioning when a cracked or broken bracket causes rattling or loose parts
• Helps reduce vibration and intermittent contact that can cause noise or poor performance
• Fits where the original molded holder has failed or become distorted

• Disconnect power and shut off water before replacing the part
• Remove access panels as needed to reach the mounting location; retain screws or clips for reassembly
• Align the holder with existing bosses or screw holes and secure with the original fasteners
• If clips or adjacent parts are damaged, inspect and replace as necessary for a secure fit