Poulan String Trimmer Parts

This is a replacement knob for a trimmer. The plastic bump knob, which is connected to a spring, is used to secure the spool. A bump knob on a trimmer may get stuck or seized and will need a replacement. Before replacing the bump knob, remove the wire from the spark plug to avoid the accidental starting of the engine. Pull off the trimmer head housing and then use a flat head screwdriver to detach the old knob. Rotate it and then remove the component. Make sure the spring is in place then align the knob before rotating and snapping it in place. Take note that pulling the knob off may take extreme force when pulling. Some knobs are screw-mounted and a counterclockwise turn is necessary to unscrew it. This genuine OEM replacement part is sold individually and is compatible with specific trimmer models from Poulan and Weed Eater.

This shock absorber is a genuine Husqvarna part, sold individually. This shock absorber can be used as a replacement part in a lawn mower. The purpose of the shock absorber in a lawn mower is to prevent excessive motion and vibration from the steering lever so that oversteering is avoided while the lawn mower is in operation.The shock absorber in a lawn mower might need to be replaced at some point within the typical lifespan of the appliance. If the shock absorber cannot function, it should be removed and replaced by this genuine OEM replacement part. Remember to always wear gloves when handling, repairing, and operating outdoor equipment. Always unplug the appliance before performing any kind of repair or replacement.This OEM part is a genuine replacement that is sold individually and sourced directly from the manufacturer. This shock absorber is compatible with the following outdoor appliance brands: Husqvarna, Poulan, Jonsered, and Craftsman.

This part is a replacement control knob. This is a genuine OEM part made by Husqvarna and has been sourced directly from the manufacturer. This part can be used to replace a broken, defective, or misplaced throttle control knob on lawn tractors.This control knob is specifically for the throttle and enables the user to easily adjust the throttle control lever. This knob may easily become detached and lost, necessitating replacement. It's important when working on or near an engine to make sure the equipment is powered off and completely cooled down before starting any repairs. For more accurate information on how and where to install this throttle control know, the appropriate owner's manual and equipment diagrams should be utilized.As an authentic replacement part, this control knob is suitable for use on several models of lawn tractors manufactured by Husqvarna, Poulan, and other brands. This is a genuine part made of high-quality, durable materials and is sold individually.

This is the outer cover for a string trimmer housing. It clips into the bottom of the reel and secures it in place behind the central button. It’s constructed from a rubberized black plastic. This plastic is designed to be as durable as possible, while also flexing slightly when it’s under pressure. The cover serves two primary functions. It holds the reel in place and also acts as a mounting point for the central button. While it’s quite durable, it may eventually wear out due to regular use. A few scratches aren’t going to put a cover out of commission, but look for areas where the plastic has been worn through all the way. Replacing the cover is easy. Simply squeeze the old cover and pop it off the assembly. Position the new cover over the reel, then snap it into place. This cover is used primarily on Husqvarna string trimmers but is also used on some Poulan and Craftsman models. This is an OEM part sourced directly from Husqvarna, and it is sold individually.

This gasket kit is a genuine Husqvarna part, sold individually. This gasket kit can be used as a replacement part in a string trimmer. The gasket kit comes with all of the necessary components required to facilitate a complete replacement or a new installation of a gasket within a string trimmer. The purpose of a gasket in a string trimmer is to seal off a certain internal area of the appliance so that oil or internal materials cannot leak out of the area of the gasket and debris cannot pass into the area of the gasket.The gasket kit might need to be ordered to conduct a replacement of a gasket that has suffered damage over general wear and tear from long-term use of the string trimmer or as a result of an accidental collision with a hard object that rendered the gasket beyond functionality. If this occurs, the gasket kit should be ordered as a genuine OEM replacement part before using the string trimmer again.This is a genuine OEM replacement directly from the manufacturer. It is sold individually. This gasket kit is compatible with the following outdoor appliance brands: Husqvarna, Craftsman, Poulan, and Poulan Pro.

This piston kit is an important component for many brands of gas-powered leaf blowers. The piston is tasked with separating the combustion chamber of the engine from the crankcase and the connecting rod that drives the crankshaft. As a kit, this product comes with both the needle bearing and the rod pin needed to replace the piston components. If a leaf blower is no longer starting, it could be related to this component. If that's the case, it will need to be replaced.The piston kit can be used to replace a damaged piston. A wrench set and a screwdriver will be required to make the replacement. Start by placing the leaf blower on a solid surface and removing the spark plug wire. After disassembling the leaf blower to gain access to the engine, the engine will also need to be disassembled to put in the new piston kit components.This is an authentic OEM replacement part that is directly sourced from the manufacturer. It is sold as a single component. The piston kit is designed to fit leaf blowers manufactured by Poulan, Poulan Pro, Craftsman, and Weed Eater.

The air filter on lawn machines protects from dirt and debris. Lawn equipment typically creates a substantial amount of dust and dirt, and the air filter is needed to ensure that dirt does not get into the engine and the carburetor. The air filters are designed to trap dirt, which means that they will eventually need to be replaced. The longer they are used, the more clogged they will become. This can prevent enough air from getting into the carburetor, which could result in issues with the engine misfiring and starting properly. Owners should regularly check the condition of the air filters and replace them when they become too dirty. This is a genuine OEM part sold individually that will replace air filters on trimmers, leaf blowers, and pole pruners. The part is compatible with a range of brands including Craftsman, Weed Eater, Poulan, and Husqvarna.

This OEM lower leaf blower tube attaches to the upper blower tube to create a long tube used to project the air from the blower. The lower leaf blower tube is the part that is located farthest from the machine itself. The upper leaf blower tube is located closest to the machine.The lower leaf blower tube may need to be replaced if it is lost or if the plastic is broken for any reason. If broken, it cannot be repaired but must be replaced. Remember to wear gloves when operating or replacing parts on any lawn machine equipment.This is a genuine Husqvarna part sourced directly from the manufacturer. This lower leaf blower tube is compatible with leaf blowers manufactured by Husqvarna, Craftsman, Poulan, and Weed Eater. Please note that this is sold individually and only includes the lower tube; the upper tube must be purchased separately in the event that it's needed.

This part is a high speed restrictor nzle that is used on blowers. The restrictor style of nzle concentrates the air stream for increased power by acting as a funnel. This nzle is twisted onto the lower blower tube. Remember to wear gloves when operating or performing care and maintenance on any outdoor power equipment. Use caution when working with any outdoor power equipment.A new high speed restrictor nzle may be needed if the original is cracked, broken, or damaged in any way. If the nzle will not turn to lock into the lower blower tube, both parts should be inspected to determine which component needs to be replaced. This high speed restrictor nzle is a genuine Husqvarna part. It is sold individually. This specific high speed restrictor nzle is compatible with blowers that are manufactured by Craftsman, Husqvarna, Poulan, McCulloch, and Weed Eater.

This starter pawl is a genuine Husqvarna part, sold individually. This starter pawl can be used as a replacement part in a leaf blower. The purpose of the starter pawl in a leaf blower is to function within the mechanism of the pull-start system so that the spring expands and contracts the starter pawl in order to release and coil back the starter rope that powers on the small engine of the leaf blower.If the starter pawl is dented, cracked, chipped, warped, or eroded to the point of reduced efficacy, the starter pawl should be removed and replaced by this genuine OEM replacement part.This OEM part is a genuine replacement that is sold individually and sourced directly from the manufacturer. This starter pawl is compatible with the following outdoor appliance brands: Husqvarna, Craftsman, Weed Eater, Poulan, and Poulan Pro.

This carburetor boot adapter is designed for use specifically on gas trimmers. It is compatible with products from Husqvarna, Poulan, and Craftsman. The carburetor boot adapter plays an integral role in connecting the carburetor to the carburetor adapter. The purpose of the carburetor boot adapter is to ensure the proper running of the carburetor and its adapter. The replacement or repair process of the carburetor boot adapter is incredibly straightforward.Since the carburetor boot adapter is made out of rubber, over time and with exposure to the elements, it will naturally dry out and crack. If this part is warped, cracked or damaged, it needs to be replaced immediately for the unit to operate properly.This carburetor boot adapter is a genuine OEM part sourced directly from the manufacturer, and it is sold individually. It is manufactured by Husqvarna.

This is a fuel cap that is used with several types of small engine lawn and garden equipment. The purpose of the fuel cap is to make sure that all gasoline in the fuel tank stays in place and there are no leaks present. The fuel cap can experience wear and tear over time or become cracked, broken, or damaged if it impacts other items. If fuel can be smelled through the cap, if the cap doesn't tighten, or if it is otherwise visibly damaged, the fuel cap should be replaced.Prior to replacement or even removing the fuel cap, the equipment should be placed in a well-ventilated area. It's also important to disconnect the spark plug wire to create a safe environment. Empty any fuel in the tank into an appropriate container before moving on. Once empty, you can replace the old cap with a new one.This is a genuine OEM replacement component that is directly sourced from the manufacturer. It is sold as a single fuel cap. The part is created to be compatible with string trimmers, hedge trimmers, and leaf blowers manufactured by Poulan, Poulan Pro, and Craftsman.

This is a replacement blade for use with hedge trimmers. The blade is the part of the tool that is used for cutting through the hedges. These blades have two different lengths of teeth to provide a better cut. The metal blades contact the cutting surface and can become covered in sap and debris. They need to be maintained to ensure sharpness and cutting ability. This includes proper cleaning and oiling. Even with good maintenance, the blade will eventually need to be replaced. It could start to corrode, or teeth or other elements of the blade could break. When there are issues with the blade, it will no longer cut properly. The cuts could be uneven, or it might have trouble cutting at all. When the blade is damaged or no longer working properly, it is time for a replacement. The authentic OEM replacement blade is sold individually and is to be used on hedge trimmers. The blade is compatible with certain models of hedge trimmer from Poulan, Craftsman, and Husqvarna. Buyers should always take the time to check their owner's manuals to ensure they are choosing the correct blade for their make and model.

A combustion engine will create a lot of pressure by igniting fuel and air with a spark. It features pistons beneath the valves and the cylinder block. Between these areas are the piston rings that have many purposes that include keeping gas compression between the piston and the wall of the cylinder, keeping a layer of lubrication on the inside of the engine, allowing adequate heat transfer, and supporting the piston inside the cylinder. This replacement piston ring is designed for use in a long list of edgers, trimmers, and blowers. It is compatible with Husqvarna, Poulan, and Craftsman machines. This is an OEM replacement part that will require a complex set of steps to install properly. It will require the use of torque wrenches, plug wrenches, pliers, screwdrivers, a mallet, and more to do the repair. It ships individually.

This is a genuine ignition module for Husqvarna engines on select outdoor lawn equipment. The ignition module includes the ignition coil and spark plug connector in a single piece. This module is used to transfer the electric charges from the flywheel magnets. This ignites the fuel-air mixture in the cylinder and creates the combustion that powers the engine. Over time, the ignition module can become worn or the spark plug connector can snap off or get damaged, causing a need for replacement. Without a properly functioning ignition module, the engine will not be able to start. This OEM ignition module is manufactured to exact standards for use in Poulan and Husqvarna string trimmers. It is a replacement for the original part and is sold as an individual unit. The spark plug and other parts and hardware will require an additional purchase. To replace this part, allow the engine to cool and disconnect the old ignition module from the spark plug. Then, detach the other side of the module and replace it with the new part. Reconnect the spark plug and the job is done. Be sure to allow the engine to cool and wear gloves when performing this repair.

This cable wire harness assembly is an OEM part sourced directly from the manufacturer, and it is sold individually. It is manufactured by Husqvarna. A cable wire harness assembly is designed for use with edgers, trimmers, or string trimmers. It is compatible with products from brands such as Husqvarna and Poulan.The cable wire harness assembly is a complete part assembly, and it includes both the throttle cable and the control wires. This item is used to run the motor as well as to adjust the engines out by linking the control handles. The replacement or repair process of the cable wire harness assembly is straight-foward, but the user replacing the part should always wear gloves during any assembly, replacement, or installation processes. The user should also refer to the owner's manual of their equipment and any guiding diagrams that clarify the placement location.