Joan June 02, 2011 for Model Number SHU 4300 series The latch on the soap dispenser does not hold, thus detergent falls out while closing the door - any suggestions?
1 Answer Hello Joan. If the latch on the dispenser is not working, you will need to replace the dispenser assembly 00263088. Hope this helps. Read More...
Tim May 05, 2011 for Model Number SHU9915UC/U12 Sorry, that was indeed the wrong model number regarding the question about reinstalling the door guards. Are they essential, and if so, where exactly do they go? Thanks
1 Answer Hello Tim! The door guard is located on the bottom of the hinge. This part keeps the hinge from scratching the door when opening. Thanks. Read More...
Tim May 04, 2011 for Model Number fdg6h8ghs0 The "door guards" fell out when I took the outer door cover off (as anticipated)to replace the detergent dispenser, and I'm not sure exactly where they go. I put it back together without them. Do I need to install them, and where exactly do the go? Thanks
1 Answer Hello Tim. The model number you provided is not working. Can you check the model number? Thanks. Read More...
Mike D. April 20, 2011 I got the model number off the right side of the door as you open it. How do I go about getting the correct part? Thanks for the help.
Mike D. April 18, 2011 for Model Number Bosch SHU5315UC/U11 Hello, I just installed this assembly and ran a load with the front door cover off so I could assure that there were no water leaks. All around the assembly where the rubber casket is fine. No leaks. However I noticed that on the right side of the assembly, looking at it from the outside of the dishwasher, there appears to be a cover missing (2”x5/8” hole) or incomplete assembly. On the original the plastic on this side is fully molded with no hole. It is fully enclosed and no water can come through. With the new assemble water will make its way through to the interior of the door via slots on the inside facing side of the assembly. I also notice that when the soap dispenser opened; the path for the water to enter the interior of the dishwasher door was lessened. This was due to the soap door covering the slots that give the water a path to the interior of the dishwasher door. If you go to your website (http://www.appliancepartspros.com/part_details.aspx?part_id=2802340) and click on the middle view it is the left side I’m referring to. If you click on the far right view you can see the slots that I’m referring to that allow the water to have a path to the interior of the dishwasher door because the compartment that the slots access is not fully enclosed due this 2”x5/8 hole. Thanks in advance for your help
1 Answer Hi Mike! You can try part number 00488964. While the manufacturer has 00263088 as the correct one for the model number you've provided. Where did you locate the model number? You have 45 days to request a refund when you buy your parts from us. Hope this helps! Read More...
1 Answer Hello Mary! The correct dispenser assembly for your model SHU9955UC/12 is part number 00490467. Thanks! Read More...
Jim Co March 30, 2011 for Model Number SHU6802UC/U06 How hard is it to install the Dispenser Assembly in this model? Can I get an instruction sheet? Or can someone talk me through it, please? I understood this was a do-it-yourself help site. I have the part I ordered but no instructions to install. Seems an oversight, to me.
2 Answers Jim, It's not hard at all,To remove outer door: ??Remove six T-20 Torx inner door screws below fascia panel --three per side (1). ??Carefully pull bottom of outer door out from dishwasher until top door tabs clear, then pull door down until it releases from dishwasher (2). Take care to not scratch outer door.??Remove two plastic door guards (3). They occasionally fall out when the outer door is removed. To remove/install dispensers: ??Remove outer door, remove fascia panel & disconnect wire harness from fascia panel. ??Disconnect wire harness from above dispenser, then remove wires to wax motor & reed switch. ??Disconnect condensation tube (for older models with condensationtubes in doors). ??Bend retainer tabs, the push dispenser inward toward tank. Protect hand with towel as edges are sharp. ??Replace from inside of tank --position O-ring seal and bend tabs to secure. When replacing dispensers, lubricate O-rings with rinse-aid & support inner doors to avoid damage if O-rings stick. I'm sure you can do it, Good Luck. Read More...
Jim Co March 30, 2011 for Model Number SHU6802UC/U06 How hard is it to install the Dispenser Assembly in this model? Can I get an instruction sheet? Or can someone talk me through it, please? I understood this was a do-it-yourself help site. I have the part I ordered but no instructions to install. Seems an oversight, to me.
2 Answers Hello Jim! I have located a link on our free repair forum that explains how to install 00263088. Hope it helps! http://forum.appliancepartspros.com/dishwasher-repair/5658-how-replace-soap-dispenser-bosch-dishwaser.html Read More...
Scott March 30, 2011 for Model Number shu4302uc/u06 When the soap dispenser door is closed, is water supposed to get thru where the door was when it was open? That little vented area has water coming thru it while the soap dispenser door is closed. It then seems to leak where the soap dispensing unit is attached to what they call a repair kit. Which is a long bent plastic tube that pushes into the dispenser. It leaks at the point where they connect. I thought it may just be that rectangular o-ring, but I was told that the oring was not sold seperately. The repair kit is like $67.
1 Answer Hello Scott. You will need to replace the dispenser assembly. They do not sell just the o-rings. Hope this helps. Read More...
Guest March 13, 2011 for Model Number SHU9915UC/11 My dishwasher detergent door won't stay closed. Do I need to replace the whole assembly or just the door spring component?