Guy September 02, 2012 for Model Number bosch shu3322uc/u12 The regular wash button (between power scrub &rise &hold)is stuck in the on position....We use the on/off switch to start the washer...Is there a repair part for this button???? Gja
Lily August 29, 2012 for Model Number SHX68R56UC The unit turns on/off just fine. But once powered on the unit will go to the drain mode for a few seconds and then reset and start again with drain mode. My husband pulled it of the cabinet and noticed there is a red plastic piece that seems to stay down to low, so he powered the unit back on and held this red piece up and noticed the water drains and slightly fills up BUT the dishwasher will not power the water through its sprayers.
1 Answer Hello Lily, These are simple to repair after a few years of figuring them out. You need to remove the power from the unit and turn off the water. Remove the water inlet valve and set it aside. Using a wet vac or wicking the water out of the base with the corners of a towel not washed with fabric softener, (this will repel the water instead of wicking it out), dry all of the water out of the base. It needs to be dry to operate properly. When this is complete, install a new water inlet valve and your repair is complete as long as you have no water leaks at the new water inlet valve. Read More...
1 Answer Hello Mark. Check and see if the door latch 00419827 is broken. If so, you will need to replace the door latch for the unit. Read More...
David M T February 24, 2012 for Model Number SHU5315UC Dish washer is not draining. Drain hoses and trap all clear. Fault code 5 ( 1 aqua sensor + 4 filling fault). What do you recommend?
1 Answer David, Here are the basic checks " Water doesn't drain properly. > Kink in drain hose. Dishwasher filter(s) or sump clogged. Straighten or replace drain hose. Clean dishwasher filters or sump. Drain motor impeller clogged. Kitchen sink or sink air gap clogged. Drain motor ) failed. Timer or control module failed." You most likely have an issue in the drain pump motor or impeller and this could be the cause of your error codes. Thanks Read More...
Bob January 29, 2012 for Model Number friggidaire lll Our dishwasher was not on and all of a sudden we smelled something burning and discovered the heating element was on with out the dishwasher on any help would be nice.
1 Answer Hello Bob! You will need to replace the electronic board. Please provide your appliance model number to verify the correct part number needed. Thanks! Read More...
Diane S. December 16, 2011 for Model Number SHU5316UC/UC11 When I turn on the dishwasher, the led shows 13 min., I can hear water circulating, the clock goes down to 1 and then justs stay on showing 1 and continues to circulate water. I'm thinking the control module is bad as it is not cycling properly. What is your opinion?
1 Answer Hello Diane. Yes, based on the information you provided, it sounds like the module 00266746 is bad and will need to be replaced. Hope this helps. Read More...
Bruce August 28, 2011 for Model Number SHU5302UC On/off switch was sticking. Finally got it to turn on and half way through the cycle the display went blank. Cycle finished but dishwasher will not turn on any more and there is still no display. Is it the switch or the board causing the problem?
1 Answer Hi Bruce. The door switch part # 00165242 will control the power to the board when the switch is closed. It sounds like you have 2 - problems including the control board. Control module - Made by Bosch. Common program control module for Bosch dishwashers SHU53/68. NOTE The manufacturer has redesigned the cover and indicator lights. Lights may be covered by the plastic case. You may have to remove the square covers over the indicator lights if needed. The same case is used for 6 and 8 indicator light models. They also no longer use the red bulb indicator lights, small surface mounted lights are used instead. Part Number: 00266746. Thank you. Read More...
Jean R. July 29, 2011 for Model Number SHU9955UC / 14 My Bosch dishwasher was working fine, and I pushed the on/off button to add more dishes and the switch didn't respond as usual. It felt like it slid forward or a spring broke?? Now it won't turn on. I can't seem to find a part that is for my 8 year old Bosch dishwasher, which I love. It is so quiet. Thank you.
1 Answer Hello Jean. Based on the model number you provided, 00175338 is the correct on/off switch. Hope this helps. Read More...
Jerry March 26, 2011 for Model Number shu5316 Can't really read the model number very well. (Model and Serial number plate is located on washer door which is 2 inches from cabinets! Tried to read with a mirror.) However, looking at the "on/off switch" (part number AP2804248), it appears that this part fits many of the Series 5300 models. I suspect that it is the correct part.
1 Answer Hello Jerry. Without the exact model number we can not verify that this is the correct switch. However we do have a 45 day return policy if you decide to order and it is not the correct part. Hope this helps. Read More...
Jerry March 26, 2011 for Model Number Bosch SHU5300 The start button will not stay in when pushed. Therefore it will not run. It will run if I hold the button in. I think the "On / Off Switch" (Part Number: AP2804248) needs to be replaced. Your thoughts????
1 Answer Hello Jerry. Yes it does sound like you have a bad switch. I am unable to locate the model number that you have provided and can not verify the correct part information. If you could double check the number directly off of the machine we would be happy to provide you with the information that you are requesting. Thanks Read More...