Cj July 23, 2016 for Model Number frigidair washer My washer comes on in any cycle for a few seconds then shuts off then repeat again.
1 Answer Hello CJ. We will need your model number to help you with this. Please call 1-877-477-7278 or post your model number with a new question on the parts page. http://www.appliancepartspros.com/modelnumber_locator.aspx Read More...
Pamela June 06, 2016 My Frigidaire stack unit ffle2022mwo is on the blink I make the selection the lid locks and it does nothing after that just some clicking noise. Usually you hear it warming up and the water starts going into the tub. We had a service repair man tell us it was the main board has gone out and it was going to be $484.00 to fix so does that sound right we would like to fix this and get the part through this site. He said this part was blinking? It went out all of sudden too no warning. Need your help please
1 Answer Hello Pamela. If he tested the board and it is bad, you will need to order and replace 5304500454 for the board on the unit. Read More...
1 Answer Eunide, You will need to check the door lock assembly to make sure that it is good. It may lock but may not active the spin switch. This is one of the most common causes. Also check to make sure that the tub spins freely by hand. If not then it could be a bearing issue. Read More...
Jim October 30, 2015 for Model Number FWFB9100ES0 Frigidaire stacked washer. First would not spin. Now lights come on and nothing happens. Cancel does not work and lights are on and will not start. Thanks
1 Answer Jim, If the unit is filling with water but not spinning or agitating then you will want to check the door lock assembly. This is the most likely cause but if the unit is not filling or anything then the control board would be the most likely cause for the failure. Read More...
Chris October 27, 2015 for Model Number LTF2940FE1 On all cycles, the washer will start humming, then the no spin light comes on an it stops. getting e23. have cleared drain pump of debris, replaced main control board, ohmed out drain pump (around 12ohm), ohmed out brown part of door switch (1350 ohm). not getting continuity on any of contacts on the door switch while engaged. Tried turning pump propeller by hand, will spin with resistance. Not sure what next.
1 Answer Chris, The E23 error code is a drain pump relay on the control board has failed. If you are still getting the error code after replacing the control board then it is possible that you received a bad control board but you will want to check the wiring between the main board and the pump assembly. Read More...
Lisa October 25, 2015 My front load washer beeps all through the wash cycle, why and what do I do to stop this?
1 Answer Hello Lisa. You need to look for a stuck button on the control panel and if there is not one, you will need to replace the control board on the unit. Read More...
David September 17, 2015 for Model Number GLTF2940ES3 Diagnostics indicated Control Board issues. Replaced the control board(those buttons and springs do present a challenge). After replacing the board, and aligning the pegs up on the dial shaft and replacing the dial, the cycle dial was 180 degrees off. Washer works just cycle dial is off. Has to be a simple fix or I crossed something.
1 Answer David, It is possible that you got the dial on wrong but there is nothing on the dial that will show what the cycle is supposed to be set for. As you turn the dial it would take you to the selected cycle then you push start. Read More...
1 Answer Hello Josh. 1. Disconnect the washer from electrical supply.2. Remove the top and the console.3. Release the ribbon by unlocking the ribbon connectorby lifting connector about 1/4 of an inch awayfrom the board. 4. Remove the (4) screws holding the control to theconsole and the (2) screws holding display to theconsole. 5. Lift the control and display off as one unit. Read More...
Josh August 28, 2015 for Model Number GLTF2940FS0 I put it on delicate it switched to a different cycle.
1 Answer Hello Josh. If the unit is changing cycles on its own, you will need to order and replace the control board in the unit. Read More...
Steve J. August 04, 2015 for Model Number GLTF2940ES0 After replacing a broken control panel plastic surround (Part # 13442700) the Washer door lock light will not light. Several attempts to run the self diagnostic tests (for better models with digital disply) have not been successful. After placing the control knob to the "TouchUp" position, the Pause/Cancel button does not turn off all LEDs. Holding the Options and Pause/Cancel buttons also had no effect on any LEDs. I've followed resetting tips such as unplugging the unit and waiting. How can I determine if the Door Lock switch or Control Board is faulty and needs to be replaced?
1 Answer Hello Steve, If the control will not go into diagnostics, the manufacturer considers the control 137006000 to be defective. Read More...