Thomas May 11, 2016 for Model Number FFBD2406NW4A Normal wash light is on but the dish washer will not run.
1 Answer Hello Thomas. Check and make sure the door switches are good. If so, you will need to replace the control panel 154887201 on the unit. You can test this with a multi-meter TJMA-DMT3. Here is a link on how to use a multi-meter. http://forum.appliancepartspros.com/oven-repair-including-ranges-cooktops/4810-how-check-continuity-ohmmeter.html Read More...
Dave May 10, 2016 for Model Number Frigidaire modelFDB1050REB2 My dishwasher will start to fill then stop and then the clean light starts to blink.
1 Answer Hello Dave. Check all the door switches and make sure they are good. If so, you will need to replace the control board on the unit. Read More...
Martin March 23, 2016 for Model Number FDB1050RES0 Runs and drains constantly and doesn't switch to heat or dry.Its cleaning the dishes so I can live with towel drying them until I can buy a new dishwasher. How long is the normal run cycle? Doesn't make sense to pay $150 for a control board when a new dishwasher is $220.
1 Answer Martin, The average timer for a cycle will be 92 minutes. If the unit is operating except drying and heating then check the heating element and connections to make sure that they are good. If that checks ok then check the thermistor for the heater to make sure that it is good. If this checks ok then check the wiring between the control and heater. If the wiring checks ok then the control board would be the issue. Read More...
Dave January 05, 2016 for Model Number FDB1050REC2 I have a frigidaire dishwasher, my son opened the door mid cycle. And it has not run since. I have turn the breaker off and tried that but no luck. It has happened before and when I used the Code it worked out good. Only problem is I don't have the sequence. Any chanc e u have proper sequence?
1 Answer Hello Dave. Control board malfunction. To determine if the control board is malfunctioning, complete the rotary switch test as follows: 1. Power Dishwasher OFF then back ON ( the Washing, Drying and Clean LEDs will flash ON and OFF). 2. Press the Heat Dry, Delay Start and Start/Cancel keys at the same time until all 7 LEDs are flashing ON and OFF. 3. Open the door and all 7 LEDs will stay ON, but will stop flashing. 4. Shut the door and all 7 LEDs will go out. 5. Press the Start/Cancel key ( depending on the position of the Rotary Switch, a specific LED will come on.) 6. Rotary Switch position and corresponding LED indicators: Normal Wash LED above the Heat Dry button Pots and Pans LED under the 2 Light Wash LED under the 4 Upper Rack Washing LED Rinse Only Clean LED With each position of the Rotary Switch, push and pull the knob. If the led stays ON without flashing, go to the next position. If pushing and pulling the knob causes an LED to go out, replace the control. Read More...
Linda May 28, 2015 for Model Number fgid2474 Why does the lights on the dash turn off when I shut the door and the dishwasher is in use.
1 Answer Hello Linda. Look for loose or bad wiring on the unit. If none is found, then it sounds like the control panel may be bad and need to be replaced. Read More...
Js April 14, 2015 for Model Number FDB1050REC2 The dishwasher will not turn off when the wash cycle is finished. I've timed it several times and for the normal wash the dishwasher keeps running beyond the estimated 89 minute length, which includes drying time. It sounds like it may be the control panel but I wanted to make sure before I spent the money to buy the control panel. Thanks for your help.
1 Answer JS, The length of time that the dishwasher runs for could be caused by a water heating issue so you will want to check the water temp coming into the unit and check the heater circuit to make sure that the heater, thermostat have continuity and that the control is sending power to the heating element. If this checks ok then the control board would most likely be the issue. Read More...
Friar T. February 21, 2015 for Model Number FDB1050REM2 My unit will not run at all. When I push the Start/Cancel button (regardless of the cycle selected), the "Washing" light illuminates, but nothing else happens; it will just sit there indefinitely with the light on. If I press Start/Cancel again (to cancel the nonexistent cycle), the light turns off, but it does not attempt to drain either. I've reset the control board by opening the breaker; it has no effect. Running maintenance mode (pressing Heat Dry + Start/Cancel from the rinse-only cycle) has the same issue; the "Washing" indicator lights, then nothing happens. Is it safe to assume this is due to control board failure?
1 Answer Hello Friar, If the unit will not go into the diagnostic mode, the manufacturer considers the control to be bad. In light of this information, I would say that if the door switches are "making" properly, the control 154712101 will be the issue with your unit. Read More...
Edwin W. December 07, 2014 for Model Number FDB1050REQ4 The wash light is flashing, but no buttons will start the cycle. I cut off power at the circuit board for 30 minutes to allow the command module to reset & all three lights ( Wash Dry & Clean ) are now blinking. After pressing the start/cancel button now the machine starts to wash dishes. but later the Wash light starts blinking again and nothing happens. Now I could purchase a new module from you BUT I can't seem to get the old one out without breaking something.
1 Answer Edwin, The error code that is displaying now would be a membrane switch failure. Main Control Board has detected a stuck key or a key pressed for more than one minute. Check connection from keypad to Main Control Board. If correct, replace keypad. If error still exist, replace Main Control Board. (Note: washing, drying, and clean s may appear in display when error code is present). Read More...
Ron R. December 04, 2014 for Model Number FDB1050REM2 What is the running cycle time for this dishwasher?
1 Answer Hello Ron, The run time for this unit will have to be estimated since there are variables such as water temperature the unit fills with, the exact voltage the unit is supplied with, (for heater temperature), whether the heated dry is chosen, etc... The time chart is on the bottom of page 2 of the units' tech sheet. Approximate time for the pots and pans cycle would be about 105 minutes. Read More...
Adam August 18, 2014 for Model Number fdb1050res When I power cycled unit it works fine. End of cycle clean light stays on. Open the door and empty dishwasher and clean light stays on. Wont start a new cycle without turning the breaker off. Door latch does work because the cycle pauses when I open the door during a wash. Controller issue?? Oh and the heater stayed on one time.
1 Answer Hello Adam. Test for a bad thermostat. If good, then replace the control board on the unit. You can test this with a multi-meter TJMA-DMT3. Here is a link on how to use a multi-meter. http://forum.appliancepartspros.com/oven-repair-including-ranges-cooktops/4810-how-check-continuity-ohmmeter.html Read More...