Michael Miller March 06, 2017 for Model Number Fggf3054mf C Frigidaire oven Hi I'm getting an F 11 error as soon as I plug the range in and continuous beeps do I need to replace the electronic controller? My model number is fggf3054mf C
1 Answer Hello Michael. Yes, based on the error code you provided, you will need to replace the erc control board in the unit. Read More...
Joe G November 10, 2016 Regarding F11 err message when replacing the oven control unit, how does one handle replacing the touch screen. Do you use old one, if so how do u remove it
1 Answer Joe, It's best and easiest to replace the overkay(touch screen), it can be removed and transferred to the new control, but it usually doesn't "look" very good if you do. But, You can use a blow dryer and warm/heat the overlay, then carefully and slowly "roll" the overlay off the control. Apply it to the new control while it is still hot, press and squeegee out the air bubbles and wrinkles, install the control, restore power and test the range operation. Read More...
Greg October 18, 2015 for Model Number Frigidaire FGGF3054MFF The oven will not light. The touch pad works normal until you hit start and 3 quick beeps and the screen goes blank. No fault or error codes. None of the functions work.bake broil convect pizza quick preheat... Nothing all same result 3 quick beeps and blank.
1 Answer Greg, With the power shutting off as soon as you hit start, this would be a faulty control board part number 316560118. Read More...
David September 22, 2015 for Model Number FGGF3054MWE Power went off for @5 minutes. At first a code of Sf (i thought it was 5f ) was on clock. Frigidaire help line said 5f meant Electronic Oven Control failure. Now it shows ( Sd ) on clock. Frigidaire said that means ( Show Room demonstration). They said to unplug it for 5 minutes, plug it back in then it would reset itself. Still shows ( Sd ) Nothing that anyone has told me to do works. Tried all kinds of reset codes, still (Sd ). If I replaced the Electronic Oven Control Module would that fix the ( Sd ) problem ?
1 Answer Hello David. It sounds like you need to order and replace the controller 316560118 on the unit. Read More...
Ash May 30, 2015 i have error code f12 . toke the plug off and re plugged it again after 30 second but still the same problem , what could the problem be ? thanks
1 Answer Ash, To properly assist you we will need your model number to help you with this. Please post your model number with a new question on the parts page. http://www.appliancepartspros.com/modelnumber_locator.aspx Read More...
Pro Gun Joe January 17, 2015 for Model Number Frigidaire FGGF3054MFF Can I re-use the overlay if a get this part or is a new one needed ?
1 Answer Pro Gun Joe, The overlay is a part that can be reused but is recommended to replace. The reason for this is because the glue residue on the back of it may not adhere properly when installing on the new controller and it may slide down during use. Read More...
Nick October 19, 2014 for Model Number FGGF3054MFF I have an error code f11, does it mean I need to change the controller?
1 Answer Hello Nick. 1. Reset power supply to range - Disconnect power, wait 30 seconds and reapply power.2. Check/reseat ribbon harness connections.3. Replace the EOC. Read More...
Raffy February 02, 2014 for Model Number frigidaire FGGF3054MF After a power surge the clock did not light up anymore. Appears the controller has no power. Is there a fuse to the controller? Burner igniters work fine and have electricity so there is electricity to the gas range, just a dead controller. Do I need a surge preventer to the range? No indication of needing a surge preventer in the manual or anywhere at all. Perhaps there is a blown fuse?
1 Answer Hello Raffy. You can use an appliance surge protector TJ041000 on the unit. You will need to replace the control board if there is power to it, and it does not light up. You can test this with a multi-meter TJMA-DMT3. Here is a link on how to use a multi-meter. http://forum.appliancepartspros.com/oven-repair-including-ranges-cooktops/4810-how-check-continuity-ohmmeter.html Read More...
Quentin December 07, 2013 for Model Number FGGF3054MF Oven and broiler does not work after power outage Ignitor was changed but oven and broiler still not working. What controls the oven and broiler on the electronic board and what is the part number that needs replacing?
1 Answer Hello Quentin. If there is no power coming to the igniter, you need to order part number 316560118. You can test this with a multi-meter TJMA-DMT3. Here is a link on how to use a multi-meter. http://forum.appliancepartspros.com/oven-repair-including-ranges-cooktops/4810-how-check-continuity-ohmmeter.html Read More...