Larry September 13, 2026 for Model Number FGGF3054MWE My stove is stuck in probe mode. I hit the probe button but it wont shut off. I tried unplugging the unit and plugging it back in. after the clock sets, it goes right back to the probe mode Is this a controller issue?
1 Answer Larry, If the probe is not in place but it is showing the probe mode then the control would be the most likely cause for this. Read More...
Toni September 25, 2023 for Model Number FEB30T6FCE When baking in my lower over the upper element never shuts off causing the oven to overheat. We have already replaced the hear sensor but that didn't fix the problem.
1 Answer Toni, with the power supply turned off, the broil element 318255605 would need to be tested for continuity from each terminal to the mounting bracket. If there is continuity, the broil element would need to be replaced. If there is not continuity, the relay control 316443912 would be the most likely cause of failure. Read More...
Mike January 29, 2022 for Model Number FEF368CCSC RANGE WORKS FINE. NO DISPLAY. STARTED GETTING DIM THEN NOTHING.
1 Answer Mike, this would be a failure in the oven clock 5303935107. Unfortunately, the manufacturer has discontinued this part and it is no longer available. Read More...
Jason March 20, 2020 for Model Number FGGF3054MFF While cooking the range made a loud Pop which did trip the circuit breaker, at reset the range instantly made another audible Pop. I reset the breaker again but the display was dead, the ignitors no longer work either. There is not "visible damage" I can see to the controller. Is it a safe bet it's the controller unit or should I investigate further?
1 Answer Jason, I would unplug the unit and pull it out, remove the back panel and check to make sure there is not a bare wire that has shorted against metal somewhere on the back. If everything looks good, I would replace the control, part number is 316560118 Read More...
Mike October 01, 2018 for Model Number FGGF3054MF Hi - some of the buttons on my oven control keypad are not working when I press them others seem to work. (I.e. bake does not work while set clock works). Does the entire controller require replacement or is some other issue causing this?
1 Answer Mike,You will need the controller and the overlay based on your color of the model. Read More...
Ralph October 16, 2017 for Model Number FGGF3054MFD In the "frequently bought together" section it is showing two overlays. Do I need both or is the page showing suggestions?
1 Answer Hello Ralph. No, you just need to buy the one for your model 316419828. Thanks. Read More...
Jay August 14, 2017 Do you know whether this part comes with the adhesive that is necessary to adhere the overlay? Or does the overlay have the adhesive? Thank you!
1 Answer Hello Jay. The overlay will have the adhesive already on it. You peel off the paper cover and apply the overlay to the clock. Read More...
Kaisersosa July 29, 2017 for Model Number FGGF3058RF The broiler on our Frigidaire Stove (FGGF3058RF) comes on but when you hit cancel to shut it off it stays on. We found it you click bake or quick bake after using the boiler and then cancel that the stove will turn off, otherwise, the top boiler stays on. No error codes and the cancel button indicates everything is off but the boiler continues to burn. Is this a board issue or something else? Thank you!
1 Answer KaiserSosa, With this issue the most likely cause would be a faulty relay on the control board which the control board would need to be replaced. The controller part number would be 316560118. Read More...
Mary July 18, 2017 for Model Number FGGF3054MFJ Was using the self clean hear a loud pop like breakers popping. I got up and noticed all the lights on the board were out. I checked the breakers and reset them to make sure. I also reset the GFI plug. Still had nothing. Now I got a new board and still nothing. The surface burners work but the oven does not.
1 Answer Hello Mary, This can be a lost connection, the ignitor 316489403, or the gas valve 316031501. You should also check the convection element 316211603. Any of these can be responsible. Read More...
Robert March 13, 2017 for Model Number FGGF3058RFA Had power outages , stove is plugged in , but no display with normal power . Burner ignitor works. thank you Bob A.
1 Answer Hello Robert. You will need to test for power to the control board. If there is power there and the board does not work, you will need to replace the control board on the unit. You can test this with a multi-meter TJMA-DMT3. Here is a link on how to use a multi-meter. http://forum.appliancepartspros.com/oven-repair-including-ranges-cooktops/4810-how-check-continuity-ohmmeter.html Read More...