Jeff May 03, 2024 for Model Number 790.46352400 I have an 18+-year-old Kenmore slip-in range model number 790.46352400 that the oven stop heating up. We noticed it when we noticed the clock on the control board was not lit. Our electricity had not gone out so I checked the house circuit breaker box to discover the stove breakers had tripped. I reset the stove breakers and the control panel lit back up. The stove top elements are all working normally. So I know I am getting 220 v to the stove plus the house breaker did not trip again. Now everything works except the oven does not heat in broil or bake mode. I have check and replaced the temperature probe which is showing 1096 ohms and doing so all the way to the control panel plug. I checked both oven elements, the lower is showing 18.3 ohms and the upper is showing 20.2 ohms. I check the fan thermal cut off and verified it by putting a heat gun on it to 200 degrees F and the fan kicked on. Is there anything else I can check before replacing the control panel? Is there a procedure I can use to check the control panel out?
1 Answer Jeff, if there is not a broken wire, the failure is in the control 318185446 based on the information provided. Read More...
Brad March 21, 2024 for Model Number fes367asc My frigidaire model fes367asc oven will not shut off the heating element, over heating-door will lock at alarm will sound can not shut it off and door code comes on turned it off at the breaker let it cool down turned back on and door unlocked but lower heating element came on with door open and would not shut off and door latch locked with the door open turned it at the breaker again to shut it down clock came on -timer will come on cannot shut off the oven when powered up what do you think I need brad
1 Answer Brad, based on the information provided, it sounds like the bake element is grounded out. This can be tested by accessing the back of the appliance, unplugging the power cord and removing the wires to the bake element, and testing from terminal to the oven chassis for continuity. If there is continuity on either terminal of the element, the bake element 318255006 would need to be replaced. However, if there is not continuity on either terminal, the oven control 318185446 would be the cause of failure. Read More...
Curt June 02, 2020 for Model Number 79046572400 I have this Kenmore range that had no lights on the the display but burners worked, did research and it pointed to control being suspect. ordered control and installed and am having same problem, so I checked breaker and am getting 120 volts on each side of breaker getting 240 across checked power block and am getting 240 volts on one side and nothing on other and nothing across power block is not damaged. at outlet am getting 120 volt on one side and 108 volts on other and 248 volts across both. I am puzzled by this. As always I appreciate all your help.
1 Answer Hello, Curt. You need to check the thermal cut off thermostat p/n AP3211049 for continuity. According to the diagram it should have two violet wires coming to it. You can test it from the control board large disconnect plug between the two violet wires. This thermostat could be located under the cooktop or at the back of the oven, behind the rear panel. If there is no continuity - replace the thermostat. You may check the oven by placing a TEMPORARY jumper on the two terminals of the cut off thermostat. Good luck. Read More...
Don P December 16, 2018 for Model Number Fes367dsa My Fridgeadaire slide in range top burners work fine but control panel goes blank and at times clock will light up but flash.It will then go blank.Range is 15 years old.Will replacing control panel fix this.
1 Answer Don, it sounds like from your description, that the control is about to go out, you will need part number 318185446 There is probably a solder joint that is weak. Read More...
Ron November 12, 2014 for Model Number FEB24S5ASB Do you have a video for a wall oven installation of a controller where the controller has to be accessed from the front (for a FEB24S5ASB wall oven)?
1 Answer Ron, Unfortunately there are no videos for the model you are requesting. You can check at the following site which may have something youtube.com Read More...
Lisa July 21, 2014 for Model Number FEB27S5DSB Do you have a control panel and handle in black for this model?
1 Answer Lisa, the black control panel is part number 318274439 and the black handle is part number 318264500. Thanks. Read More...
Ward February 22, 2014 for Model Number FEB386WECG Do you have a control panel for wall oven serial # NF9111703 in black or stainless?
Boni S. February 09, 2014 for Model Number FEB386wech I have a wall oven that needs a new control panel. Serial #nf01012144 model #feb386wech. Do you carry this item?
1 Answer Boni, the black control panel is not available, however, stainless is available as part number 318041702. If you need the electric control behind the control panel it is part number 318010700. Unfortunately, this item has been discontinued with no further replacements or cross references available and our company is unaware of any other available sources. Sorry about that! Read More...
Bryan H January 21, 2014 for Model Number FES367ASG The burners work but the oven will not come on. Will a new controller panel fix this or is there another solution?
1 Answer Hello Bryan. If there is no power coming from the control board to the element, you will need to order and replace the board 318185446 on the unit. You can test this with a multi-meter TJMA-DMT3. Here is a link on how to use a multi-meter. http://forum.appliancepartspros.com/oven-repair-including-ranges-cooktops/4810-how-check-continuity-ohmmeter.html Read More...
Gay December 21, 2013 I have already ordered and received the part. My ovens control panel is in the front. Do you have a video that shows how to replace it?
1 Answer Gay, In order to properly assist we would need to have the model number.Please post your model number with a new question on the parts page. http://www.appliancepartspros.com/modelnumber_locator.aspx Read More...