Jack July 20, 2016 for Model Number FFEF3015LSM Hello. The Broil, timer, clean, and bake lights are all on. The stove appears to work just fine. what's going on and how do I fix it?
Steve L June 29, 2016 for Model Number FEFL79DBK Hot surface light will not go out when stove top is cold and oven is cold.
1 Answer Hello Steve. You will need to test the switch and see which one is sending power to the light when turned off. Read More...
1 Answer Tom, To replace the indicator light, you will need to pull the unit out from installation. Unplug the unit and remove the cover over the back of the control panel. The indicator light will be located here and you would unclip from the lens and clip the new one on. Read More...
Dilip November 13, 2013 for Model Number KENMORE ELECTRIC STOVE MODEL #790-97453804 Indicator light stays on for both left coils, front and rear coils, even though the surfaces are cool. What do I need to replace? What might be the proble? Coils control knobs for both front and rear coils works fine. Only the indicator lights (yellow lights)stay on all the time.
1 Answer Hello Dilip. If there is power coming from the switch, replace the switches. You can test this with a multi-meter TJMA-DMT3. Here is a link on how to use a multi-meter. http://forum.appliancepartspros.com/oven-repair-including-ranges-cooktops/4810-how-check-continuity-ohmmeter.html Read More...
Duane S. October 31, 2013 for Model Number fef352dsa My oven light stays on all the time. I've checked the door for closure and the toogle switch on top.
1 Answer Hello Duane, You need to check the door switch 316445501 and the connections to it. If the switch is broken, it will require replacement. If the connections are shorted together, you will need to correct the electrical connections so they do not contact one another. Read More...
Mike October 23, 2013 for Model Number kenmore 790.9661 electric range Replaced the clock/timer now everything works, but the hot surface indicator lights any suggestions?...Thanks Mike
1 Answer Hello Mike. You will need to check the hot wire going to the P terminal of every switch. Somewhere the wire is unhooked or is bad. Read More...
Amy June 12, 2013 for Model Number 790.95662100 I have the part # to fix my hot surface indicator. How do I get to that area to replace/fix it? On the control panel or the top of the range needs to open up?
1 Answer Amy, If the indicator is on the control panel then you will need to remove the back cover of the controls. If the indicator then you would need to lift the main top by removing 3 screws under the top in the door opening. Read More...
Lisa H March 17, 2013 for Model Number GLGF386DCG Hi all,you were very helpful in assisting me with replacing my clock timer,worked like a charm. Fantastic site. Unfortunately, we jostled the red "Speed Bake" Indicator Light (Part AP2124115) inadvertently while replacing the control panel/timer and cannot seem to figure out how to get it back in place. The stove only has small hole where the red indicator light goes (to right and top of control panel when facing back of stove). The part (which includes the red plastic indicator and actual lightbulb behind it) appears to be supposed to clip onto something to hold in place, but there is nothing to clip it onto. We tried to remove the red light and insert from front and it falls thru when you try to attach back to the white box on the other side. If you try to insert from back to front, nothing is able to hold the light assembly into place. Any ideas that might help us? Thanks you very much--again your sight is really fablulous. Given the great advice you shared to fix original problem, I thought I'd check in before I resorted to "superglue" or "duct tape" and see if you had run across this issue before?
1 Answer Lisa, The red indicator is the light lens 5304462665 and should be pushed in from the front and the light would clip to it. If it is falling through then you will need a new light lens. Read More...
Gene May 21, 2012 Please tell me on Electrolux part # 316022500 Light/Lamp Indicator the placement of the yellow and white wiring. I thought the yellow wire goes on the bottom and the white wire goes on top of Indicator, but when connected as stated the light does not work. The oven works fine.
1 Answer Hello Gene. That is correct. If the light is not working, then the switch may need to be replaced on the unit and not the light. Read More...
Rob January 19, 2012 for Model Number 790-92320302 the hot surface light shorted out , now the oven won t work if I replace the indicator light will that fix the oven?
1 Answer Rob, Sorry, but no replacing the "hot surface" indicator light, will not solve the issue with the oven. You do need to remove the control panel rear cover panel and check for damaged wires in the control panel and make sure you have the proper power supply to the range. These are two separate, individual circuits, and the L1 circuit/wire is the common link at this point. Unless you have two issues as a coincidence. Good Luck and Thanks Read More...