Jeff February 12, 2021 for Model Number wf328aaw/xaa I have a samsung front load.washer showing nd error. I replaced the drain pump and that didnt work. I just replaced the door latch and that didnt work..Everything functions mechanically and drain is not plugged. Machine starts and washes but stops on the rinse/spin cycle at 27 minutes left and just stays there. If I manually shut it off and on and move it to spin cycle sometimes it will take off and spin out. Can anyone help? Thanks
1 Answer Jeff, it would be recommended that the pressure hose is inspected for any partial blocks that may be causing the pressure to not reduce in the hose properly. If there is not a partial block, the pressure sensor DC97-03716C can be tested for voltage during operation from the main control MFS-WF318A-T0 (main control has been discontinued by the manufacturer and is no longer available). At the connection CN3, the black probe of a meter would go to the orange wire at pin 6 and the red probe would go to the purple wire at pin 7. There should be a 2.5VDC reading if the main control is sending voltage properly. From there, the red probe would get moved to the pink wire at pin 8 and there should be a 2.5VDC reading here if the sensor is sending a signal back properly. If the voltages are reading properly, the failure would be in the main control. Read More...
Jon August 28, 2020 for Model Number FFRE12L3S10 If I let the unit set for a while it will turn on and work correctly. As it continues to run it shuts down and you can’t get anything to light up or work. Thank the sleep time comes on at .5 and the system still won’t run. Unplug it let it set for a while and it will work again. Could this be a control board. Thank you
1 Answer Jon, Yes, the issue could be the PC board(We have no part number listed, for the model number you supplied). But you also want to check the power cord 5304536807 Power Cord and the connections to the PC board, first. Thanks, Read More...
Clifford Messer August 17, 2020 my window ac which is a Frigidaire when u set it on temp in a few minutes the temp runs its self all the way to 90 by its self and I set it back at 70 few minutes back it goes to 90 and some time it will not let me change it at all thanks for any advice
1 Answer Cliff, Only guessing because there is no model number listed here. But you most likely have either a stuck button on the keypad or a control board issue Read More...
Mike July 07, 2020 for Model Number FFRA06L2S12 The MODE button on keypad not working. Does your part AP4558681 fit my FFRA06L2S12 window AC? If not, is there a different part? Thanks!!
1 Answer Mike, That part is not available from the manufacturer as a replacement part. The remote control is available but not the main control assembly. Read More...
Steve March 20, 2020 for Model Number LRA157mt1 When I turned the unit off ,the compressor keeps running.
1 Answer Steve, This issue of the compressor continuing to run would most likely be caused by a faulty main control board 5304492070. Read More...
Myslinskijoe September 21, 2019 On off button doesn't work what color are wires to button for on and off
1 Answer Myslinskijoe, We will need to have the model number of your unit to be able to assist properly with your question. Please supply the model and resubmit your question. Read More...
Israel August 02, 2019 for Model Number Ffre1233s10 The buttons on the display board dont work do you have a replacement part and whats the part # thanks
1 Answer Israel, unfortunately, the manufacturer does not list the controls as a replaceable part. Read More...
Brandon July 18, 2019 for Model Number Frigidaire FFRE1233S1 The buttons on the unit don't work. The remote doesn't work either. It's stuck on and I had to unplug it to turn it off.
1 Answer Hello Brandon, The problem is a stuck relay on the main power control board. I'm sorry but Frigidaire has not listed a replacement part number for the part needed to complete this repair. Thank you for your patience and understanding in this matter. Read More...
Garett July 16, 2019 The control panel is not letting me adjust temp, turn on and off, or change fan speed, but it does put its self in sleep mode which is the only button that responds when pushed? I am also unable to locate the model information, but I am sure it's the 10,000 model
1 Answer Garett, as there are many types of models, the model number would be needed to be able to accurately provide information. For assistance in locating the model number, the link can be found on our repair help page at https://www.appliancepartspros.com/repair-help/ just under the search bar. Read More...
Anita May 11, 2019 for Model Number FFRE18L3Q22 I have a Frigidare window air conditioner. When I plug up, it comes on, goes & back on again, then temp starts flashing from 44 counting down. I push mode button to cool & temp sets to 70 degrees, it only runs on high cool, will never turn off. Runs cold a long time, then just blows air. Have to unplug to turn off. None of the buttons on panel work. Could this need a new control board?
1 Answer Anita, With the buttons not responding and the unit only working on high cool then this would most likely be the control board that is faulty. Read More...