Jay November 16, 2016 for Model Number BGHD2433KW1 How do I install this part as the dishwasher has 2 ears/socket holes and the sensor does not have those extra locking pieces?
1 Answer Jay, On the side of the sensor there are pieces that should stick out and the sensor will just push up into place and lock in. Read More...
Maryann November 02, 2016 for Model Number frigidaire dishwasher model fgbd2431kq Question, the heating element in my dishwasher is not getting hot and will not dry the dishes, It was tested and was told the part is good but the thermal sensor needs to be replaced. What part is a thermal sensor? Called frigidaire and they do not know. I was quoted a high amount to repair and I want to see if it is worth the money. Please advise and thank you.
Bill June 23, 2015 for Model Number FGHD2465NF1A Water is present in the bottom after a completed cycle. If I restart a cycle and then cancel it drains completely. Was told it may be a timer problem??? Help please. Thanks
1 Answer Hello Bill. Check and make sure the water is not flowing back into the unit. If not, then it sounds like the drain pump may be bad A00126401 and need to be replaced on the unit. Make sure the drain hose is not partially blocked on the unit also. Read More...
Frank December 06, 2014 for Model Number FGHD2433KW1 The drain pump runs on and off long after wash is done and each time the door is closed.
1 Answer Frank, With the drain pump running when the unit is not turned on, this would be caused by a faulty control board. The part number that would be needed is 5304514670. Read More...
John H November 05, 2014 for Model Number LGBD2432LW0A Dishwasher water is not getting hot. I have replaced element and thermostat with no change. What could be the problem?
1 Answer Hello John. Make sure you get the water hot at the sink first. Then if it still does not heat, you will need to replace the control board 807024601 on the unit. Read More...
Daw April 07, 2014 for Model Number FGHD2433KW1 Frigidaire Unit little used in three years. The water flows to the dishwasher. The drain pump works. The main circulation pump does not work. Have cleaned bottom screen and sump. No debris. Pump impeller turns freely. No error codes on panel. No motor hum. I noted the motor has two power connections and three other wire connections. The two wires are for power to the motor. The other are control inputs/interlocks to the motor? Are there any switches in line with the motor control interlock wiring that can keep the motor from running? What is this switch and how can I test?
1 Answer Daw, The switch that you would be referring to would be the hall sensor. The hall sensor can be checked for resistance but the manufacturer does not supply a resistance rating for the part. Read More...
Jay January 12, 2014 for Model Number Fghd2433KF1 Water not pumping out....doesn't appear to be a clog. Back flushed drain hose with air and it blew water and air back int to the sump. How do I know if its the motor or the pump that's bad?
1 Answer Hello Jay. If there is power to the pump, and it does not drain, and is not clogged, you will need to replace the pump A00126401 on the unit. You can test this with a multi-meter TJMA-DMT3. Here is a link on how to use a multi-meter. http://forum.appliancepartspros.com/oven-repair-including-ranges-cooktops/4810-how-check-continuity-ohmmeter.html Read More...
Stan S November 07, 2013 for Model Number FGBD2445NF Water is leaking from the sensor seal. It won't hold in position when I try to push it back in. The water has ruined the laminated floor floor under and in front of the unit. What can be done?
1 Answer Hello Stan. Try replacing the sensor and see if the leak stops. If not, the sump may be bad in the unit. Read More...
Allen August 13, 2013 for Model Number fghd2433kb1 uo code after attempt to run cycle. Run diagnostic code HS continues to flash.. Replaced vent with new still error code uo when trying to start cycle. diagnostic showing hs code also after new part
1 Answer Allen, Here's some information : " UO > Vent open > While in wash cycle, Main Control Board does not receive signal from vent assembly that vent plunger is closed. Plunger status is sensed with optical sensor in vent assembly. Check wiring between vent assembly and Main Control Board. If wiring correct, replace vent assembly. If error still exist, replace Main Control Board. hs > Hall sensor > The control has sensed an error with hall sensor in motor. Check wiring between motor and Main Control Board. If correct, replace motor. If error still exist, replace Main Control Board. You'll want to recheck the connections at the vent assembly, and check for loose or damaged insulation on the harness at the bottom of the door. Then you'll need to remove the filter screens etc. and check to make sure there are no debris or articles stuck in the impeller on the wash motor assembly. Read More...
Ron April 19, 2013 for Model Number fghd2433kf Water in dishwasher does not pump out. I replaced the pump, but water still does not pump out. When I hit wash cycle and reset, a low hum comes from new pump. Thank You
1 Answer Ron, You will want to check the sump to make sure that it is not clogged causing water to not get to the drain pump. Also check for clogged or kinked drain line which would also cause this issue. Read More...