Alta December 20, 2013 for Model Number GJXRP080DAWW My agitator coupling bolt got loose, the agitator coupling is attached to the agitator and the complete assembly (agitator with the coupling) is out of the machine. The agitator coupling threads are worn out, I would need to replace it. The problem I am facing is how to remove the agitator coupling from the agitator. I see in some of the video they ask to put the complete assembly on the ground and hit the agitator coupling from top, however in my assembly I dont have access to the agitator coupling from top. The top part of the agitator is screwed to the bottom with four screws/bolts from underneath. Can you please suggest a way to remove the agitator coupling? Thanks, Alta
1 Answer Hello Alta, Start the screw into the coupler through the hole in the agitator like you were going to install it. Instead of tightening it down, only start the screw into the screw hole and reach in with a long piece of wood such as a piece of an old broom handle and hit it with a hammer. This should pop the coupler from the agitator. Now remove the screw and the agitator should be loose enough to pull from the bottom of the agitator. Read More...
Broski December 13, 2013 for Model Number WH43X10034 The upper agitator seems to be loose, as it wiggles around very easily, even with the washer off. Is there a way to replace just that, or does the entire agitator assembly need to be replaced in order for it to work properly? The lower half rests nicely on top of the coupling bell and spins properly, it's just the upper part. Thank you for your help!
1 Answer Hello Broski. If it is to loose, you will need to order and replace the agitator in the unit. Read More...
Rae December 01, 2013 for Model Number LSC6244AQ0 My agitator seems broken. It turns fine at the bottom, but halfway up, its loose and doesn't turn properly when doing the wash. Is my solution just to purchase a new agitator? Or is there possibly more of a problem. Thanks for your help!
Kerry October 18, 2013 for Model Number wjre5550h1ww The video is not available on how to replaced the agitator for the GE hydrowave. Note I have the regular agitator #WH43X10034, not the flat agitator. How do I remove it? Is the tall agitator like mine bolted in? Thanks!
Larry October 03, 2013 for Model Number GE Hydrowave GTWN4250D0WS Like many others I have clothes caught under the agitator and need to take it off to free the draw strings of the pants. From reading other answer it looks like it might pull off (perhaps using a rope?) but didn't want to assume that if a bolt holds it in place. Unbolt or pull? Also, is there anything I can do to prevent this machine from eating things? Our old GE washer never did that! Thanks for your help!
Ron October 02, 2013 for Model Number Gtwn4250m1ws How does the AP3965155 agitator for a Gtwn4250m1ws washer come apart? It seems like theres a cap that is sealed & i can't get it off to tighten the bolt. Heeelp!
1 Answer Hello Ron. The cap does not come off. You run a rope under the agitator and jerk upward to remove the agitator from the unit. Read More...
Stephanie September 27, 2013 for Model Number WLSR3000G5WW Hi. I have this part on my washer that just doesn't want to come up. The came came off with a good hard tug but this piece is not wanting to come up. I have read some other posts where they say to put a rope under to help with leverage and pull up but nothing budged. Can you help? Thanks :)
1 Answer Stephanie, When you put the rope under the agitator and use leverage you will want to work your way around the agitator with the rope to get the agitator off. Also pull the agitator cap and just make sure that there is no bolt holding the agitator in place. Read More...
Justin L September 14, 2013 for Model Number GE Profile WPRB8050D1WW We are constantly getting lint on our clothes from the washing machine. Already tried the basic troubleshooting tips. Think we might have to clean the lint trap. Guessing it's somewhere in the agitator. How can I remove the agitator in this model to get to the lint trap? If there's a screw, then it is difficult to get to because underneath the fabric softener assembly is a hard round plastic cap that I can't get out from the center of the agitator assembly. Thank you for any help you can provide.
1 Answer Justin, You will want to take a rope or something similar and run it under the agitator. Working your way around, pull up on the agitator. You will need to use leverage and force to do this. Read More...
Gwen September 05, 2013 for Model Number GTWN3000M2WS I have a garment caught under the agitator and I need to know how to safely remove and replace the agitator
1 Answer Hello Gwen. Run a rope under the agitator and jerk upward to remove it from the unit. Read More...
B.O.B September 03, 2013 for Model Number WJSR4160GWW Does everything a washer is suppose to do, BUT dose not agitate. called a repair service and they said it could be one of two parts but wouldn't tell me the name of parts cause have to have it serviced by one of their service techs. PLEASE HELP...
1 Answer Hello Bob. It sounds like the coupling WH43X10032 will need to be replaced on the unit. Check it out and see if it is bad on the unit. Read More...