Justin July 28, 2014 for Model Number whdsr315d0ww My GE washer does not agitate or spin, but it drains just fine. The belt seems to be in good shape. When it is time for it to spin, I hear a noise from the top part of the washer where the timer/cycle dial is located. Any idea what might be wrong?
1 Answer Hello Justin, This can be the timer WH12X10254, the transmission WH38X10002, or the clutch, (which is made on the motor assembly WH20X10019). The timer is most likely since you hear a noise from the control panel during the failure. Read More...
Ron G May 26, 2014 for Model Number GTWN4250D1WS I have a ge washer model GTWN4250D1WS. The top portion of the agitator does seem to engage and pull cloths down into tube. I fixed this problem on my old machine by replaces the dog ears, but cant find where this can be done on the GE model. Only reference I can find is to replace either the agitator assembly or the coupling. Is there not a way to take the agitator apart and replace dog ears?
1 Answer Hello Ron. No, if the agitator is not working, it sounds like the coupling WH43X10032 will need to be checked out. These do not use dogs. Read More...
Bob N May 16, 2014 for Model Number WWRE5240D0WW Making noise during agitation and agitator was loose. Removed agitator, also does it have to have water in tub to work after agitator is removed?
1 Answer Bob, The agitator being loose would cause a noise to occur and for the unit to agitate the water level does have to be met. Read More...
Gilberto S. May 10, 2014 for Model Number Maytag model Mav 6458Aww serial24401887 E N this mashine is nat strike, O bat but if you took out the Water
1 Answer Hello Gilberto, If the drain pump WP35-6780 feels normal and you cannot see a wavy piece of metal above the pump pulley the issue will either be the thrust bearing 12002213 or the spin bearing W10219156. Read More...
Jack April 29, 2014 for Model Number Lat9316aae Does the agitator lift off or is there a screw or bolt?
1 Answer Hello Jack. There is a locking screw in the side of the agitator. You loosen the screw and lift the agitator out of the unit. Read More...
Jason March 26, 2014 for Model Number WH49X10042 & WH43X10034 Hi, I have a GE washer. The agitator stops turning and it looks not broken. The washer can still spin and drain. The belt and motor seem fine. Do you suggest to replace the agitator coupler, agitator assembly or both? Thank you. Jason
1 Answer Hello Jason, I would recommend to replace the agitator coupler WH49X10042. You should verify this is the correct part by the model number from your units' I.D. tag, since it was not listed in this post. I normally verify it for each customer but could not for this reason. Read More...
Rose February 22, 2014 for Model Number 11026842690 The agitator doesn't draw the clothes down to the bottom of the washer. The top of the agitator seems loose and when I put my hand on the top and push down it seems to agitate correctly... The machine it self seems to be working, don't think I need to replace the little teeth(that's what I call them), dogs.
1 Answer Hello Rose. Part# 285748 the agitator repair kit should get you up and running. Read More...
Sundari R. February 09, 2014 for Model Number GE washer modelWDSR2080DECC Agitator coupling bolt - can we order this part separately - what will be the part number Thank you
1 Answer Sundari, The bolt is no longer sold separately. You will need to purchase the Coupler kit part WH49X10042. Read More...
Vivian January 10, 2014 for Model Number WH43X10034 Hello, My agitator stopped turning, I took it out and the bottom of the agitator was broken, so i thought that was the problem. I received the new one and put it on correctly, now it turns but very little. Can you help me know what should i replace instead? Thank you.
1 Answer Hello Vivian. It sounds like the coupling WH49X10042 may be bad on the unit as well. Read More...
Dana D December 31, 2013 I have a whirlpool washer I have had it for nine years the problem is that the top part of the agitator is broken it will not push the clothes down. What do I need to do about this? Thanks Mr. Dana D. Walton
1 Answer Hello Dana. Depending on the model, it sounds like the cam kit for the unit will need to be replaced. Read More...