Nora April 23, 2013 for Model Number wpse7003a0ww About 5 minutes into the wash cycle of my washer, a loud clicking noise starts and last for a few minutes. Then the washer stops and sits for 3-4 minutes. When it begins again it does not continue on the wash cycle, but starts to drain and then spin (so my clothes are only getting washed for that initial 5 minutes). During the spin I hear the loud clicking noise again. It then continues through the other cycles and I don't hear the clicking noise again. What could be causing this?
1 Answer Nora, This issue sounds like it would be an issue with the control board on the unit. The clicking noise would be the relays on the board WH12X10138. Read More...
John G. April 20, 2013 for Model Number wcse3100aww The start button is not working. We push it in and it is not turning on. Will part #ap3422790 / mfg. part #wh12x10225 be the right part?
1 Answer Hello John, You should first check the lid switch WH12X10141 and the lid switch magnet WH12X10276. These are trhe most common cause of the complaint you have listed. Read More...
Tim April 09, 2013 for Model Number Wbse3120b1ww My wash machine will go through the entire wash cycle and then stop after 10seconds on final spin cycle leaving the clothes still wet..what's up.
1 Answer Hello Tim. Check the pump and see if it is clogged. If not, you will need to order and replace the control assembly WH12X10225 on the unit. Read More...
Debbie March 20, 2013 for Model Number GE top loader My washer will complete wash cycle and then when it goes to spin out, it will stop. I can here the humming sound of the motor and I would lift the washer lid and close it back down and it would start, sometimes and other times it would not work, I would have to hit the start button to get it onto the spin cycle now nothing works. The humming is still there but none of my 2 options work any more.
1 Answer Hello Debbie. Check and see if the pump is draining on the unit. If not, then it sounds like the pump is the issue of the no spin. If it is not clogged, you will need to replace the pump on the unit. Read More...
T.H. December 07, 2012 for Model Number GE WASHER WBSE2090 Our GE washser model # wbse2090 is skipping the final spin cycle and I hear the motor running specially with heavy loads but it does not spin. Pump and Agitator coupling just got changed and did not solve the problem. To get it started on the spin cycle I move the timer to the final spin cycle and push the start button more than once, remove some of the cloths and put them back after it starts spining. Is it the lid switch or Clutch that need to be replaced. Thank you
1 Answer Hello T H This would not be a lid switch issue but a clutch issue. The clutch WH5X256 and belt would need to be replaced WH1X2026. Read More...
Jeff June 10, 2012 for Model Number whre5260e1ww The wash machine will fill and will not start wash cycle. Would this be the lid switch causing it not to start? Also sometime it will start washing and stop before it completes the cycle.
1 Answer Hi Jeff. Yes the lid switch senses the lid closed for safety. From the symptoms described then replace the lid switch. Lid Switch Kit - Item Number: WH12X10141. For the magnet assembly order WH12X10276. Thank You. Read More...
Sevastian August 15, 2011 for Model Number WHRE5550K2WW Will this be the correct lid switch for my washer? I also need the part# for the board and tranny.
1 Answer Hello Sevastian. Based on the model number you provided, WH12X10334 is the correct lid switch, and WH38X10017 is the mode shifter, and WH12X10439 is the control board. Hope this helps. Read More...
Kim June 03, 2011 for Model Number WJSE3110A0WW My GE Washer will not agitate or spin. The repair guy says the problem was the belt. It worked for two loads now it's doing the same thing! What could it be? The repair guy now says its the lift/lid switch, not sure which one of those but now he's not answering and I'm not sure he knows what he's doing, please help!
1 Answer Hello Kim! If the unit is not going into the spin mode it could well possibly the the lid switch WH12X10141. If the lid switch has become defective, it will not allow the unit to go into a spin mode as a safety feature. You can check the lid switch with a multimeter MA-DM1. Here is a link from our free repair forum you can refer to for help with using a multi meter. Hope this helps, thanks! http://forum.appliancepartspros.com/oven-repair-including-ranges-cooktops/4810-how-check-continuity-ohmmeter.html Read More...