1 Answer Hello Michael. Make sure the lid switch is good on the unit. Thanks. You can test this with a multi-meter TJMA-DMT3. Here is a link on how to use a multi-meter. http://forum.appliancepartspros.com/oven-repair-including-ranges-cooktops/4810-how-check-continuity-ohmmeter.html Read More...
Nelson March 14, 2017 Is there a replacement part for DP035-043 and/or what part can be substituted? Thanks,
1 Answer Hello Nelson. The part number you provided DP035-043 is not valid. We will need your model number to help you with this. Please call 1-877-477-7278 or post your model number with a new question on the parts page. http://www.appliancepartspros.com/modelnumber_locator.aspx Read More...
Scott March 03, 2017 for Model Number WCVH6800J2WW My pump went out on my washer machine is there a cross reference number or model I can use or does it have to be the DP040-018 and can I just order the pump motor and not the whole assembly?
1 Answer Scott, The drain pump assembly for the model number you supplied is WH23X10028 / WH23X10028 Drain Pump Assembly. It is a "complete" unit" individual parts are not listed and will require a pump assembly. The part is in stock and available at this time. Thanks, Read More...
Jeffrey February 19, 2017 for Model Number wsre5200d1ww I notice under wash machine some water. I suspect it is the water pump but not sure. I have the front cover off trying to locate the source. I still can't find it. Does the pump leak? It doesn't look it has any seams to do so. Thanks
1 Answer Hello Jeffrey, If your model number is actually WSRE5260D1WW, it is possible for the drain pump to leak but normally you will need to use a flashlight to see if you can locate water trails leading down from the source of the leak. You see, there is no such thing as pure water in a washing machine, so when it leaks out, the water will evaporate and mineral deposits or soap in the water will not evaporate. This will leave a light trail where the water once ran and is only visible by shining a flashlight on it from an angle. Following it up to the the high point will normally reveal the source of the leak. Read More...
Amy January 07, 2017 for Model Number WPGT 93630 EPL Which part replaces Hanning Drain Pump DP040-012?
Diego R. December 08, 2016 for Model Number WPSE4270A0WW The wáter pump not work. What is the part number? The current pump assembly seems to have a fan facing what would be the front of the washer. Thanks
Bill October 21, 2016 for Model Number WPRE6150K2WT Washer stopped mid cycle. Will not run any cycle. Ran thru error code clear and nothing. Removed front and there is no error. Red light flashes constantly as if there is no problem. Washer has not run is over an hour and pump is still very hot. Replaced motor and transmission sometime back. New Transmission was bad and had to diagnoses it again and re-replace it. Bad pump?
1 Answer Bill, If the unit will fill with water but not do anything you would want to check the lid switch on the unit to ensure that it is good. If this checks ok then would likely be a control board issue WH12X10525 with nothing operating at all. Read More...
Deborah September 30, 2016 for Model Number WBXR1060T3WW The current pump assembly seems to have a fan facing what would be the front of the washer. I do not see this on the replacement part but it does look like there is possibly an area with a fan enclosed. It says this pump assembly will work with my model, but will I also need to buy the fan? I can send a picture if you can provide an email address.
1 Answer Deborah, The original drain pump [WH23X81] for the model number you supplied [WBXR1060T3WW] has been "substituted" by the manufacturer. The correct drain pump is WH23X10030 / WH23X10030,it is a "direct factory replacement" part and will operate in your machine. The cooling fan on the motor assembly is no longer visible, but it is there. You shouldn't have any issues replacing the part, and the part will operate properly in your machine. Read More...
Scott September 29, 2016 for Model Number wjre5500g1ww Hello, The temperature setting is on Hot/Cold, the hoses are connected correctly, yet the water is cold on both cycles.
1 Answer Scott, The unit getting cold water only will be caused by a faulty control board. The part number needed for the board is WH12X10404. Read More...
Austyn L September 24, 2016 for Model Number Glwn5050m0ws Hello, for GE washing machine (model# glwn5050m0ws) I am wondering which pumps work for it? Is that model number for my washing machine and the pump has a different model number or what? Sorry, just a bit confused.