John March 05, 2017 for Model Number rpw302 Will this suspension rod work on my rca rpw302 3.0 cu ft washing machine. The old rod is about 24 1/2 inches long and where find buy repair manual book with this model in it please email.
1 Answer John, This rod and spring assembly will be approximately 26 1/2" long and will not work for this model. Unfortunately we do not have a service manual for this unit. Read More...
Peter November 04, 2016 for Model Number WHRE5550K1WW I see that for my model GE washer it has the Green "414 Washer suspension rod assembly" and the White "415 Washer suspension rod assembly". There are a total of 4 Washer suspension rod assemblies supporting the tub correct? Assuming all 4 (if there are 4) Washer suspension rod assemblies are defective would I need to purchase 2 Green (WH16X10141) and 2 White (WH16X10057) ? The parts list does not state total quanitity that are required per washer (that I can find).
1 Answer Peter, Yes to get the suspension rods then you would need 2 white and 2 green as there are 4 rods. Read More...
Jessica September 20, 2016 for Model Number Gtwn7450h1ww Does this rod and spring asm work for my washer? Ap5607528
1 Answer Jessica, The rod and spring assembly for your unit will be part number WH16X10174. Read More...
Kenny August 19, 2016 for Model Number gtwn8250d0ws Hello, I have a top load GE washer model gtwn8250d0ws. Recently the drum has dropped 2 to 3 inches. The washer still functions but moves more than normal and makes more noise. From what I have read I may need the support rods and Springs. But when I do a search for parts for my model, I get numerous different ones... yellow, green, black, white, etc. When I try to use the tool to check for compatibility I get the message that they aren't with a link right back to the same page. How do I know which ones I need. BTW, mine are white. Please let me know how to find the correct parts.
1 Answer Kenny, The part number for the rod and spring assembly on your unit will be WH16X10168. Read More...
Matt October 29, 2015 for Model Number WHRE5550K2WW Is this the right part for the front suspension rods on my GE washer WHRE5550K2WW? The washer makes a screeching sound during agitation cycle on anything but tiny loads, and I can see with front panel removed that the motor casing was scraping against the bottom of the machine. Is it OK to replace only the front 2 rods, or do all 4 need to be replaced at once for balance? From looking at other questions, I see you sometimes recommend the apron kit for this symptom, but I don't notice much sag in the apron. Any sure way to know whether it's the apron or the rods? Thanks much.
1 Answer Hello Matt. The apron is bad. You will need to order and replace the apron WH49X20925 on the unit. Read More...
Sinfulmonkey November 09, 2014 for Model Number WPRE6150K1WT I have a GE washer model number WPRE6150K1WT. I have a guy come and check my washer because it was making a really loud noise. He told me that I needed to replace the shocks. My question is what parts do I need to buy so that when I go to actually take this washer apart I'm not missing anything that I needed to put it back together correctly. Are there any rubber pieces or anything that are sold separately that I am gonna need ? Thank you in advance for your help. Sinfulmonkey
1 Answer Sinfulmonkey, The rod and spring assembly comes with all the parts needed and would not need anything extra to replace. Read More...
Mike September 09, 2014 for Model Number WPRE6100G0WT Are there any tricks to replacing the Suspension Rod Supports? Can you give me an outline of the steps to follow? Thanks much, Mike
1 Answer Hello Mike. There is no special tricks for changing the rod springs. You may want to have an extra pair of hands to help support and lift tub. You disconnect the power. Then remove the front and top panel. Lift the tub and remove the old rods. Install the new ones as you remove the old ones from the unit. Read More...
Solmimi February 09, 2014 for Model Number WJRR4170G0WW My GE washer has white shocks on the front and green on the back. Your diagram shows the opposite. ?? Also, my tub has gradually overtime "sagged" in the front, causing the metal frame tabs under the motor mount to drag on the bottom of the. Washer frame. I'm assuming it has to be the shocks, correct?
1 Answer SolMimi, With the tub of the washer sagging you will need to get the apron kit WH49X20925 which will correct the issue that you are experiencing. Read More...