Gk December 04, 2013 for Model Number WM2277HS I am getting the LE code on my Washer and just had a repair man come out and he changed out part number 4413EA1002B. It worked fine when he left but I am getting the LE code again. Now he says the main board needs to be replaced. Every thing I have read the hall sensor needs replaced. Can you tell me if the board has anything to do with the LE code. Washer seems to work just won't go into spin cycle. Any help would be appreciated.
1 Answer Hello GK. Most likely the RPS Sensor. However, can be the board or wiring harness, but would start with the sensor. Read More...
M. Smith October 20, 2013 for Model Number WM2277HW My LG washer's tub stopped spinning. In Trouble Shooting mode, the drum will move slightly and then shake a little. I measure each winding set of the stator, each combo was about 8.1ohms. Again, with the washer in T/S mode I measured 208V on 2 combos and 0 on the third. I ordered the 6871ER1003C Control Boards (incorrectly listed on this site), but I am getting the same result. Except for one difference. I am only getting 208V on on output combo from the new board.
1 Answer M. Smith, This issue sounds like it would be caused by a rotor position sensor 6501KW2002B which is the most common reason for the tub to not spin and to be jumpy in the test mode. Read More...
Tran P October 11, 2013 for Model Number wm2277hw My washer has code PE and no spins is it main control problem?
1 Answer Tran, The PE error code is for a pressure sensor error and the sensor switch assembly 6601ER1006E would need to be replaced. Read More...
Rbn April 19, 2013 for Model Number Lg WM2277HS I need a main circuit board and just wondering if part AP4440232 is the right one for WM2277HS
Ric March 11, 2013 for Model Number WM2277HW My LG washer is getting an LE error. The Tech came out and swapped the hall sensor and the stator assembly to no avail. He thinks it's the Main PCB. He didn't have a rotor to swap. On your website, I see two part numbers . 6871ER1003C and 6871ER1003F. Which one is correct. Is this part number on the board itself? When I put the washer in SPI cycle, the drum will not move and after 3 or 4 min I get the LE. When I put it in RINSE CYLE only. The drum will move in both direction sometimes but is a bit noisy and eventually display LE. When I power off the washer and move the drum by hand clockwise and counter I don't feel a lot of resistance. Please advise.
1 Answer Ric, The LE error code would not generally have anything to do with the control board. These are the things that would need to be checked. The connector 3 pin male white in the motor harness for being connected to the connector 3 pin female white of the stator assembly. The electric contact between the connectors in the motor harness and 4 pin female white connector in the main pwb assembly for being bad or unstable. The motor harness between the stator assembly and the main pwb assembly is cut (open circuit). The hall sensor has already been replaced so it will not be that. But the wiring needs to be checked. Read More...
Mark January 30, 2013 for Model Number LG WM2277HW I have a LG washing machine that has been giving us the LE code for about 1 month. But just the other day my wife tried to turn on the machine and it would not power up at all, no lights, nothing. What do you suggest?
1 Answer Hello Mark. Make sure the outlet is good for the unit and test for power to the control board. If there is power there, and the board does not work, you will need to order and replace the control board on the unit. You can test this with a multi-meter TJMA-DMT3. Here is a link on how to use a multi-meter. http://forum.appliancepartspros.com/oven-repair-including-ranges-cooktops/4810-how-check-continuity-ohmmeter.html Read More...
Henry November 23, 2012 for Model Number LG WM3431HW Good Day: I am searching for a main circuit board for our LG washer/dryer combo. The model number is WM3431HW and serial number is 00859002002140025860. Our assistance is appreciated. Thank you
Ang August 24, 2012 for Model Number WM2277HW Is Item Number: AP4440232 for sale a "New" Item, "Refurbished" or in "Used" condition? Thank you.
1 Answer Ang, all parts sold with AppliancePartsPros is new from the manufacturer. Thanks! Read More...
Md July 07, 2012 for Model Number LG washer WM2277HW LE error code: Replaced stator sensorand it worked for a few loads. LE is back again. Is Stator has issue or is the main board the problem? The machine would not spin. Turned drum by hand and I see sound and light on front panel.
1 Answer Hello M.D., This sounds like a communication problem between boards. The usual fix is to check the electrical connections by dis-connecting and re-connecting the connectors one at a time. The service manual says this: • The connector (3-pin, male, white) in the MOTOR HARNESS is not connected to the connector (3-pin, female, white) of STATOR ASSEMBLY. • The electric contact between the connectors (3-pin, male, white) in the MOTOR HARNESS and 4-pin, female, white connector in the MAIN PWB ASSEMBLY is bad or unstable. • The MOTOR HARNESS between the STATOR ASSEMBLY and MAIN PWB ASSEMBLY is cut (open circuited). • The hall sensor is out of order/defective. Let us know if we can assist you further. Read More...
1 Answer Chinh, according to your model number the main pcb is part number 6871ER1078T. Thanks! Read More...