Robert September 23, 2013 for Model Number WM2487HWM LG Front Loader I keep getting a FE error code. Smaller loads seem to help but some times the water does not what to stop going into the machine. It is always on the rinse cycle. I alway rinse in cold water. Is this a fill valve issue? or a sensor issue? Part numbers would help. Thanks!!
1 Answer Hello Robert. It sounds like the unit is siphoning out the water in the unit. Check and make sure there is only 6" of drain hose in the drain pipe. Also, make sure the drain pipe is 36" off the floor in height. You will need to check and make sure the drain hose has an air gap going into the drain pipe. If it is air tight, it will siphon. Read More...
John August 22, 2013 for Model Number lg washer wm2075cw How do I access the water level pressure sensor to blow it out or replace it (Manufacturer Number 6601ER1006E)? I can tilt the machine on it's back and get to the connecting tube, but it appears that the front panel has to come off to actually get to the sensor.
1 Answer Hello John. You will need to remove the top panel on the washer to access and blow through the pressure hose on the unit. Remove the screws on the back of the top panel and slide back and lift off the unit. Read More...
Jt June 09, 2013 for Model Number wm2016cw Hello i have a LG washer that as a OE error code. Washer in rinse and spin cycle will fill and drain out the water and no water is in tub but it keeps on spinning and draining for about 10 mins and throws an OE error code. Checked drain hose clear, pump clear, pressure dome for pressure switch has been cleaned out, wires conneced. Should i change the pressure switch?
1 Answer Hello JT. Based on the error code, you need to check and see if the drain hose is stuck to far inside the drain pipe and causing the unit to siphon out the water. It sounds like the issue you are dealing with in this case with the water not filling the tub assembly. Read More...
Jose R May 23, 2013 for Model Number wm2487hrm I have... well it my wife's washer she gets the LE code which sensor is the correct one to change, Is the the assm or the roto sensor. Please help she driving me crazy LOL m
1 Answer Jose, The rotor position sensor 6501KW2002B is the part that needs to be changed for an LE error code. Read More...
Jarett March 11, 2013 for Model Number WM2487HWM During the wash cycle there isn't enough water in the drum. I know it is water efficient but there isn't enough to wash or rinse.
1 Answer Hello Jarett. The water level in the unit will be low. This is normal. If it were to low, the machine would shut off with an error code letting you know the water level is not correct. Read More...
Michelle C December 12, 2012 for Model Number WM2487HRM My machine is making a noise from the left side, as if it is a card in the spokes of a bicycle. It happens before a wash or spin cycle. It is loud. Does it have something to do with the water being pumped out of the machine? It happens throughout the wash cycle, not at just one point during the cycle.
1 Answer Hello Michelle. You need to check and see if something is stuck inside the pump. If not, replace the pump 4681EA2001T on the unit. Read More...
Spring November 16, 2012 for Model Number wm2487hrm Washer has power but wont start. Display lights up but immediately turns back off when I let go of start button.
1 Answer Hello Spring. Based on the information you provided, it sounds like the PCB 6871ER2019B is bad and will need to be replaced on the unit. Read More...
German October 17, 2012 for Model Number WM2277HW I Have a WM2277HW I replaced the drain pump the door switch because I was getting errors OE and Door error. My machine cycles all the way to rinse gets stock like for 5-10 mins. and then gives me an OE error. Last night I had to unplug the washer because the door would not open.Someone please help.
1 Answer German, The "OE" error code indicates a "drain" issue. If the control doesn't see the pump empty, or thinks there's water in the tub, the door will not unlock. Your next check needs to be the water level sensor 6601ER1006E and the air tube between the switch and the tub connection. Disconnect the hose from the switch and blow in the end of the hose, this usually clears any debris or clogs in the hose. Read More...
Rob August 11, 2012 for Model Number wm2487h*ma Is the part AP4440713 the water level sensor and where is it located in the machine?
1 Answer Hello Rob. 6601ER1006E is the water level sensor and is located under the top panel on the side of the frame. Read More...
Becky July 25, 2012 for Model Number WM1812CW What is this sensor commonly known for, what is its function?
1 Answer Hello Becky. 6601ER1006A is the pressure switch and is used to determine the level of the water in the unit. Read More...