William June 10, 2024 for Model Number RB2155SH/XAA My refrigerator and freezer will not restart after it reaches temperature, If I unplug it and plug it back in it will restart and cool fine until it reaches temperature again, The displayed temperature on the door does not change until you do a restart.
1 Answer William,Thanks for your question, and based on the information provided you will likely need to replace the main board. Read More...
Carl October 17, 2021 for Model Number RB1855SW Rb1855sw ice building. Thermal fuse is ok. Temp sensor is ok. Drain pan heater has contunuity. Is it now absolutly sure that it's control board problem? Thanks
1 Answer Hello Carl,due to the results of your checks then yes the next step is to replace the control board, DA41-00128D. Read More...
Bruce September 21, 2021 for Model Number RB1955SH The display on the front shows the temp I set but the temp inside both freezer and fridge is much higher, and the compressor not running. If I shut power off and back on the display shows the correct temp and the compressor starts running. Then when the temps get to where they are supposed to be, the compressor shuts off, the display remains the same and the insides heat up. Another person had this problem and you sent him a bulletin. I couldn’t find that bulletin online. Thanks for any help.
1 Answer Bruce, unfortunately, there is not a service bulletin specifying this model. However, the thermistors can be tested for resistance and they should measure 4690 Ohms at 80°F, 7032 Ohms at 60°F, and 8867 Ohms at 50°F. The thermal fuses for the defrost circuits would need to be tested for continuity as well. If one shows open, both would need to be replaced with the defrost thermostat DA47-10160H and the defrost sensors DA32-10105R would need to be replaced as well. If the thermistors and thermal fuses test good, the main control DA41-00128D would be the likely cause of failure. Read More...
Ronnie September 09, 2021 for Model Number rfg297-aawp my samsung rfrigerator is cool but my bottom freezer dont freeze
1 Answer Ronnie, You will want to pull the rear cover in the freezer compartment and check the frost pattern. If there is very little frost pattern then this will be a sealed system issue and will require service. If there is heavy frost pattern then you will need to check to see if the evaporator fan motor is running. If it is not then test to see if there is between 7 to 12 VDC getting to the fan motor. If there is not then the main board would be the issue and if there is then the fan will be the issue. If the fan is running and there is heavy frost then it will be a defrost issue. Read More...
Pat August 17, 2021 for Model Number SAMSUNG RF32FMQDBSR/AA I HAVE ERROR CODES 14E & 40E. THE TOP FRIDGE WORKING FINE . THE BOTTOM FREEZER WORKING.
1 Answer Pat,The 14 E appears to be an Icemaker error code. When power gets restored to these units they will run a self-diagnostic mode and display any errors. This ice maker error does not seem related to the FF section not cooling. However, the unit may not run until the error is cleared.The 40 E code on my Samsung refrigerator? What do you need to do first?1. Remove food from the freezer. 2. Remove the inner cover of the back wall. 3. Melt the accumulation of ice with a steamer and wipe everything dry.4. Replace the panel. 5. Press the upper right and left buttons on the dispenser & hold them for at least 10 seconds. Read More...
Eric Bremer September 15, 2019 for Model Number RB1844SW Fridge and freezer get down to temp and quits running. Temp gauge on front seems to read temp it quits running at. when unplugged and plugged back in the temp gauge on front reads actual temp and begins to cool back down. After say 6-8 hours it shuts off and have to unplug it and start over.
1 Answer Eric, You will want to check the thermistors on the unit to make sure that they are good. If they are then the issue will be in the main control board. Read More...
Dc In Seattle May 12, 2019 for Model Number RB1944SL The fridge and freezer will cool down to the setpoints. However once it reaches those and shut down the cooling cycle the temperature gauge stops responding to warming temperatures and just displays the temps when it shut down even though it is warming up. Since it thinks it is still cold enough the compressor doesn't come back on again. If I unplug and replug the unit, the display temps show the actual temp again and compressor starts and it starts to cool. I've checked the temps with a remote gauge and they roughly correlate once it resets and it does cool so I don't think it is the temp sensors, fans, capacitor, or compressor. The coils are clean and I gave it a defrost just in case. What should I do next?
Jon April 23, 2019 for Model Number RF25HMEDBSR/AA-0000 Samsung French door fridge evap coil and ice maker freeze up. Also the flex zone control keeps beeping and changing temps on its own. The only way I can stop it is by holding and locking the dispenser. What could be the problem?
1 Answer Jon,The first thing i would do is disconnect the unit from the wall outlet for at least five minutes so it is able to reset. If the problem still persists after the unit is powered back on then i would suspect the dispenser control.DA97-14424A Read More...
Robert Neal December 21, 2018 for Model Number RB2055BB Temperature indicators on door say freezer temp is 10 degrees and refrigerator temperature is 40 degrees, but neither compartment is cold. What should I replace?
1 Answer Robert,You would want to make sure the evaporator fans running and condenser fans running and compressor needs to be running. If fans are running and compressor trys tio run then you hear a click then the start relay is probably gonna be your issue. The overload and relay parts are DA34-10003D DA35-00099J Read More...
Kevin September 28, 2017 for Model Number RB1855SL Samsung fridge. Fridge on top, freezer on bottom. Fridge temp fluctuates from 3 C up to 7 C and beeps when this happens. It always goes back to 3. The circ fan in fridge does not run. I checked it and got about 156 ohms resistance and fan ran when I applied 120 vac, I checked thermistor and it seems to be ok, i.e. ohms in ballpark and they decrease as temp goes up. Wondering if it is the board or more accurately the fridge fan rely. Can I ust buy relay or need to buy board? Thanks
1 Answer Hello Kevin. If the relay on the board has failed, it is always recommended by the manufacturer to replace the board. They do not offer just the relays for purchase. Thank you. Read More...